Jump to content

Recommended Posts

Hi there folks

Does any one know what kind of wood is best for the outer skin of planking if I want a slightly exaggerated (raised) surface grain. I intend painting my model (Lynx) black above the water but don't want it too smooth.  The Lynx was hiding in the Chesapeake waterways when she was captured and I doubt she was done up like a show boat.

Perhaps there might be ways of raising the grain a little after sanding???

 

Thanking you all in anticipation

Don

Link to comment
Share on other sites

Don,

This is purely a guess, because I haven’t tried it, but it seems to me that one of the characteristics of a weathered hull is that the seams crack and the individual planks start to show.  It may be possible to simulate this, after painting the base colour on the hull, by using some slightly textured paint (paint with some dust in it?) and touching in each plank separately.  That may provide the necessary delineation and texture.

Any treatment of the planking prior to painting seems more likely to merge the planks rather than to delineate them.

John

 

Past Builds:
Diorama, Washington & Philadelphia - 1776.  1:144 scale scratch build

Sir Edward Hawke - Schooner, 1776.  1:72 scale scratch build from H Hahn plans

Matthew - 1497.  1:25 scale scratch build from Colin Mudie plans

Mediterranean Cog - 1343.  1:40 scale scratch build from Xavier Pastor plans

Nonsuch - 1650.  1:32 scale Aeropiccola kit

Caustic - gunboat, 1776 . 1:36 scale scratch build

Member of the Nautical Research Guild

Link to comment
Share on other sites

Try using wood stain conditioner; on certain woods it does a good job of evenly raising the grain.

Ken

Current build: Maersk Detroit"
Future builds:  Mamoli HMS Victory 1:90
Completed builds: US Brig Niagara, Dirty Dozen, USS Constitution, 18th Century Armed Longboat
https://modelshipworld.com/index.php?/topic/11935-uss-constitution-by-xken-model-shipways-scale-1768/

 

Link to comment
Share on other sites

This comes from instructions for wood dyes:

Dissolved in alcohol - the dye does not penetrate as deeply- but it has no effect on the wood surface.

Dissolved in water - the dye penetrates deeply - but raises the grain.

Pre-treatment with 10% PVA in water, dry then sand the surface - the next water exposure with the dye will not further raise the grain.

 

Based on this,  wet your surface with 10% PVA in water and let it dry.  If it raises the grain too much, try a light sanding with 320 or 400 grit.

 

NRG member 50 years

 

Current:  

NMS

HMS Ajax 1767 - 74-gun 3rd rate - 1:192 POF exploration - works but too intense -no margin for error

HMS Centurion 1732 - 60-gun 4th rate - POF Navall Timber framing

HMS Beagle 1831 refiit  10-gun brig with a small mizzen - POF Navall (ish) Timber framing

The U.S. Ex. Ex. 1838-1842
Flying Fish 1838  pilot schooner - POF framed - ready for stern timbers
Porpose II  1836  brigantine/brig - POF framed - ready for hawse and stern timbers
Vincennes  1825  Sloop-of-War  - POF timbers assembled, need shaping
Peacock  1828  Sloop-of -War  - POF timbers ready for assembly
Sea Gull  1838  pilot schooner - POF timbers ready for assembly
Relief  1835 packet hull USN ship - POF timbers ready for assembly

Other

Portsmouth  1843  Sloop-of-War  - POF timbers ready for assembly
Le Commerce de Marseilles  1788   118 cannons - POF framed

La Renommee 1744 Frigate - POF framed - ready for hawse and stern timbers

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...