Flying Cloud 1851 by hof00 - Mamoli - 1/96 - American clipper

[hof00]

Hi All,

Lower Channel update....

 

I began by pinning the Fore Lower Channels to the Hull, easy enough.

I then decided to make s Mock-Up, (Prototype), the Channels to fit the Chainplates. (I had already drawn this out....)

As per my Drawing, the Chainplates were too short, esp. the Backstay Chainplates.

Regarding the Backstay Chainplate with respect to the Lower Channels, the slot that I would have to cut in the Lower Channel to accept the Chainplate would leave about 1.5mm thickness where the Channel meets the Hull, far too thin.

 

The kit utilizes a 2.0mm thick strip mounted on the Lower Rub Rail to simulate the Lower Channels.

 

I now have to choose the way forward:

• Not really keen to construct/replace the Chainplates
• Lower Channels are not designed for this kit
• Not 100% accurate to leave Lower Channels off
• Photo, (On Box), looks just fine without Lower Channels
• Pushing ahead with Lower Channels risks breakages
• KISS - Keep It Simple Stupid

Finally, what am I building this for? It is something that I enjoy, not a gift or presentation.

My decision to omit the Lower Channels may upset some who are following this thread but that's just the way it is, constraints of the kit, engineering/design do not allow for modification.

 

So, in conclusion, this model will be "Devoid" of Lower Channels

I have tried and prototyped to install these items; I have to admit a small defeat....

 

With this attempt out of the way, I can concentrate on mounting/positioning Chainplates with only Upper Channels.

 

In saying all of the Above, I will most probably install a 1.0mm strip on the lower Rub Rail where the Channel would have been, this will assist in Marking and positioning individual Chainplates and will be more in keeping to the kit design.

 

Onward!! Many more challenges ahead.... 🙂

 

Cheers....HOF.

 

Photos:

 

 

 

 

[uscharin]

On 11/29/2025 at 2:03 AM, hof00 said:

took the plunge and purchased a X Y Table and Clamping Vise

 

I like that table.  Maybe it's time for me to go shopping.

 

Your ship is looking great!  She has a very "authentic" and natural look.

 

Ron

[rwiederrich]

Sorry to hear the lower channels didn't work out for you...though I do see them used in your mock-up.   I'm still not clear on how they are trouble for you....but to each his own.  Each modeler is guided by the level of authenticity they are able to tackle.  Personally, I draw the line at being a purist, by being captive to only using wood for the construction of my models.  I use whatever suites me.  Knowing full well that a good coat of paint will disguise whatever sacrilegious material I employed.

 

Your model is stellar and you have constructed her skillfully.

 

Rob

[hof00]

6 hours ago, uscharin said:

 

I like that table.  Maybe it's time for me to go shopping.

 

Your ship is looking great!  She has a very "authentic" and natural look.

 

Ron

Thanks Ron,

I'm trying my best, my first at 1/96.... Tolerances are much "Tighter." 🙂

Yup, the "Table" has already proved its worth, edge drilling 1.5mm Lower Channels, even though they will not be used.

 

Cheers and Regards,

 

Harry.

[hof00]

4 hours ago, rwiederrich said:

Sorry to hear the lower channels didn't work out for you...though I do see them used in your mock-up.   I'm still not clear on how they are trouble for you....but to each his own.  Each modeler is guided by the level of authenticity they are able to tackle.  Personally, I draw the line at being a purist, by being captive to only using wood for the construction of my models.  I use whatever suites me.  Knowing full well that a good coat of paint will disguise whatever sacrilegious material I employed.

 

Your model is stellar and you have constructed her skillfully.

 

Rob

Hi Rob,

Thank you very kindly for your comments, much appreciated.

I'll go with what I am comfortable with and with what "Prototyping" shows me.

Even though not 100% I am hopeful the finished result will be acceptable. 🙂

 

Cheers and Regards,

 

Harry.

[Ian_Grant]

I too like that X-Y table. Hmmm, one would look good on my drill press.......must start grooming the Admiral to the idea.......😏

[tmj]

Fantastic job! 

[hof00]

Hi All,

Small update, no photos as yet.

I have been struggling with the Chainplates for some time.

I have decided to put the kit supplied parts in the "Too much trouble" basket and manufacture my own.

This has the possibility of Lower Channels "Back in play" and this is what I am working towards.... (I am pleased that I kept these....)

 

I have had many E-Mails with Daniel from Dusek Models to ascertain if he had replacements for Flying Cloud. (As it happens, he does, and they are an improvement in the form of Laser cut Aluminum.)

I am still keeping my options open here, Daniel will review the Shipping cost in a couple of weeks but mentioned to me that the Shipping would probably be around 60.00 Euro.

Hats' off to Daniel thus far for his efforts and Customer Service!!

 

Tomorrow will be more "Experimenting" with Chainplates, and I'll post photos of development ideas in a few days.

 

BTW All the best for everyone in 2026!!

 

Cheers....HOF.

 

[Rick310]

Really think you should add the lower channels as this is historically correct, even if it means remaking the chain plates.  If you don’t, I think you will always regret not adding them when you had the chance.

Beautiful model!!

Rick