Jump to content

Recommended Posts

Posted
49 minutes ago, palmerit said:

A shot of the faring from underneath

Beautiful job on the stem to bottom-planks joint! The transom/knee/bottom should be fine once planked over, but it does confirm the worry I had earlier.

 

But those frames! I am so glad that the Model Shipways dory had frames secured to a building board. I do not envy you having to sand and bevel with them standing up like that.

 

Trevor

Posted

The kit has you add temporary supports to stiffen the frame on the build board while planking. 
 

Adding one of the garboard planks (after beveling the upper end). Will let the glue dry before adding the other garboard. 

IMG_6822.jpeg

IMG_6823.jpeg

Posted

Slow progress on the Dory - just haven’t had time to work on any models. Added a couple more planks. 
 

The Midwest Dory is twice the size of the Model Shipways Dory (about the same length as my Sherbourne). 

IMG_6831.jpeg

IMG_6832.jpeg

Posted
7 hours ago, palmerit said:

The Midwest Dory is twice the size of the Model Shipways Dory

They are different boats, modelled at different scales.

 

The Model Shipways one is a 15ft dory (dory sizes being measured as length of bottom, not overall) at 1:24. A 15ft dory is a two-man boat and towards the large end of banks dory sizes. In the 19th Century, they were used in halibutting, while the cod fisheries used smaller dories. I'm not sure but that may have changed before the end of the Canadian dory-schooner fishery in 1963.

 

The Midwest dory is modelled at 1:12 and looks to have a 13" bottom. If so, it represents a 13ft prototype, suited to the banks cod fishery or else fishing along the shore, but still a two-man boat. It also looks to have much stronger sheer than the Model Shipways one, so a different design within the same overall family.

 

 

But, either way, yours is coming along nicely, Palmerit!

 

 

Trevor

Posted
Posted

Thwarts (seats) dry fitted. They’ll be glued in place later, after painting the interior. Not sure if I’ll paint or stain the thwarts or just seal them. 

IMG_6867.jpeg

Posted

I started airbrushing the Dory. I found a couple sources for some colors and after playing around with some colors in my stash I decided on Vallejo Model Air 71.135 Chrome Yellow for the inside and most of the outside, Game Air 76.123 Angel Green for the gunwale, and I’m doing the garboard and bottom in Model Air 71.271 German Red Brown. 
 

I don’t know if it’s a combination of airbrushing and the model being basswood but it’s been hard to paint over pencil marks I had made. With my Sherbourne (offwhite Vallejo Air on pear wood) I didn’t have trouble covering the pencil marks I made). I ended up painting with a brush to get a thicker covering over the pencil marks and I will do more airbrush coats. 

 

https://goodmorninggloucester.com/2009/03/22/dory-buff-dory-paint/

 

 

 

IMG_6877.jpeg

IMG_6878.jpeg

Posted

Dories and "dory buff" paint are still very much a living tradition in Nova Scotia. Human memories fade, of course (though not as quickly as the pigments in 1920s marine paints 😀), but I've never heard of anyone doubting that all Lunenburg schooner's dories were buff with green trim. That's just the way to was and still is.

 

Trevor

Posted (edited)

I know that yellow is not quite Dory Buff color, it was the closest I had in my paint staff. The green was in the ballpark. I think I saw some photos of some Dorys with some reddish undercoat on the garboard and bottom and just went with it.

Edited by palmerit
Posted (edited)

I'll need to make and paint my oars and I've been researching paint/stain schemes. The Midwest kit instructions say "Thwarts, Oars, Mast, and Boom - Clear", which I assume just means putting a matte varnish on the oars. I might do the same. I have some stains I could try to use too. I also saw a model that had them painted the same yellow as the interior.

 

This great build (of the Model Shipways kit) just has the oars plain, I think stained and weathered: 

 

 

I just noticed that the Model Shipways Dory kit optionally recommends adding leathering (simulated with thin paper painted a leather color) that I might add to these oars. I had completely missed that that was in that Dory's instructions when I built it. I did add them to the oars when I did my Pram since they're a clear step in the instructions.

image.png.19e3455c59d371cd60aa513c7d0641b9.png

Edited by palmerit
Posted
25 minutes ago, palmerit said:

the Model Shipways Dory kit optionally recommends adding leathering

I don't think I have ever seen (full size) dory oars leathered. For one thing, there's not much need, when they are worked between (rather soft) thole pins, versus metal crutches. For another, in the days when dories were rowed in the ordinary course of a day's work, the oars were disposable items. (Even the dories did not have long working lives, when battered about on the decks of schooners.)

 

Each to their own, of course, but I didn't leather the oars of my dory model. I will leather the ones I put into my pram.

 

Trevor

Posted
31 minutes ago, Kenchington said:

in the days when dories were rowed in the ordinary course of a day's work, the oars were disposable items

That might also be why most of the photos - of models, of real Dorys - have plain wood oars.

Posted

Testing out some stain colors (on scrap basswood) for the thwarts (seats). Leaning toward colonial maple (far left) I think. Might try some other stains I ordered. Saw that Dory oars are often made from white spruce. Don’t know if the thwarts would be the same. 

IMG_6949.jpeg

Posted (edited)

I picked up a couple more stain colors (these are the small 8oz), gunstock and ipswich pine. 
 

 

 

IMG_6953.jpeg

IMG_6954.jpeg

Edited by palmerit

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...