KenW

Greetings Fellow Modelers
 
Thanks to all for your fine comments, for the "likes" and to those watching quietly.
 
 
More Fish Hold Stuff
 
Continuing on with the fish hold, the next step was to build the back walls of the bunker partitioning.  In the drawing below, the hold is defined by the yellow cross-hatching and the back wall partitioning by the green lines.  The back walls are individual bunker partitions, but for this model I've simplified it as a single one-piece wall.  The blue dots are the vertical posts used to segment the hold into individual bunkers/pens.
 

 
 
To begin, I created a paper template of the area to be walled.
 

 
 
Planking was glued directly to the paper template.
 

 

 
 
Styrene channel was glued on at each post base location. The proper depth channel needed for this is not manufactured, but I found an “H” column that was close enough once modified.
 

 

 
 
The back wall pieces were then glued on.  A corner torn from a Post-it note makes a hands-free right-angle square.
 

 
 
At this point, I became aware of two errors that needed to be addressed.  First, the height of the perimeter partition walls, and the bulkhead end walls were too short.  This would allow a view through an open hatch to see above the walls.  It would be an extreme angle view to be certain, but a deck mock-up proved to me it was possible.  The second error is that the forward bulkhead end wall was placed 12 scale inches forward of where it should be. That's a problem because it interferes with the proper placement of the mast, which is unacceptable.  So, a second end wall was installed 12” aft of the first one.
 
In the image below the new (taller) end wall is on the right.  One would now expect that the two forward bunkers are 12” narrower than the other bunkers, but they are not.  The post spacing is correct from the aft bulkhead forward and only the forward wall was misplaced.  Indeed, I caught this error because the forward bunkers appeared to me a tad wider than the others.
 
Extra work caused by working carelessly.
 

 
 
Next, the four-sided posts for the bunker partitioning were made.  They are a five-piece styrene construction.
 

 
 
 
A construction jig is assembled. The styrene is modified “H” columns and strips from Evergreen.  Solvent cement keeps the posts from being inadvertently glued to the jig.
 

 
 
A channel is placed into the jig.
 

 
 
A flat strip is cemented on top of that. Two of these channel/flat piece assemblies are made for each post.
 

 
 
The center rectangular strip is added to one of the above assemblies.
 

 
 
Then both assemblies are cemented together.
 

 

 
 
The posts are glued onto the post bases.
 

 
 
One of the back walls is heightened, a channel extension is glued on, and a partition is installed.
 

 
 
The partitions are cut from blanks of edge-glued wood strips. A paper template of the partition is placed on the blank and the shape is cut free. They are stained with chalk and alcohol. I use alcohol to liquefy and apply the chalk because it penetrates the wood and evaporates off quickly leaving no time for the thin wood strips to warp.
 

 
 
I used “super thin” CA to glue these partitions in.  With the partition already in place, a drop of the CA at the top of the post races down the channel and glues most of the plank ends.  I have an extension tip on my bottle to help control the flow and I use the watery glue infrequently and cautiously.  I feel there should be a “skull and crossbones” on the bottle.  If you must use it, keep a can of fresh acetone at the ready.  A mishap will glue your fingers together instantly with the possibility of a trip to urgent care.  Am I exaggerating?  Not really.
 

 
 
The partitions are all in.  I'm considering partially filling a few of the bunkers with ice.  What do you folks think and what would make a convincing 1:48 ice?  It would have to be a non-soluble material.
 

 

 
 
I've installed 8 surface mount LEDs (one over each bunker) to light up the hold.  That seems like a lot, but they are small and their output will be adjustable.  Two wood strips holding four diodes each are assembled.  These LEDs are SMD 805 warm white and are attached to the strips with a clear (when dry) version of Gallery Glass.  For scale, the grid on the mat 1/2” (12.7mm)
 

 
 
Both strips attached over the bunkers.
 

 
 
Thanks for stopping by.
 
Be safe and stay well,
 
Gary
 
 

The preliminary design for the stern carvings are now complete, I’m going to review them and make any adjustments necessary and proceed with the prototype sets. Looks like I need to get moving on the model so I have something to attach these beauties to.
 
JJ

I’m back in the states, making  a pit stop home to laser cut a few things, I should be back at it in a week or so. Will post some updates as I begin my planking journey. 
For now here are some photos of the Everest base camp trek, which took me above 18,500’ and through 32 miles of rough Himalayan terrain but the views were simply spectacular!
 
JJ
 

Yupp....I have always done this on every ship model that I have made showing the scuppers.  Works like a charm.

To scupper or not to scupper.
 
Most contemporary models do not show the scuppers.   In fact the contemporary model of Speedwell doesnt show the scuppers. I didnt add the scuppers on my Winnie build which was typical.  But I am going to show them on my speedwell.   Nothing fancy.   These arent too crazy to do.   Not like the hawse holes will be.  But you do have to be careful.  You need to carefully measure them inboard and outboard so they look like they line up.  You can actually use the deck planking templates because I have marked the inboard locations for all of the scuppers.
 
When I drill my scuppers I dont even try to drill them all the way through.   That adds unnecessary difficulty.   I drill shallow holes only about 1/16" deep or slightly more.   Inboard, I start with a small pilot hole with a small drill bit.   Then in this case, I used a #47 drill bit afterwards to make them larger.   Finally I used a round file to smooth out the hole’s insides.   I lightly sanded the inboard bulwarks over the scuppers with some 400 grit sandpaper to smooth out any fraying.  This will require some paint touch-up later when they are all done.  The scupper holes were made flush with the deck level or just a hair above.
 
I prefer to use a soft pencil to darken the inside of the holes.  I made sure to cover the entire inside surface of the scuppers including the back of the hole.   Then I touch up the red bulwark paint.  On this model I drilled the scuppers before I added the waterway.  I just wanted to try something new.  It worked out really well for me.  No chipping or fraying of the water way at all.  You can do it whichever way is more comfortable for you.
 
The picture below shows the holes drilled and darkened with the pencil.   They are nice and dark.  I touched up the red paint as well on the bulwarks afterwards.  You can see the waterway strip also prepared in advance and ready to be glued into position.
 

The waterway is a 3/64" x 3/64" strip of cedar.  I sanded one of the four corners of the strip down its entire length.  I used an Emory board or sanding stick.   Basically I made it triangular in profile.  Then I held it in position so I could mark the positions for the scuppers along its length.  I really tried to get these exactly where they should be located.  I used a round mini file to make the half round openings along the length of the waterway where the scuppers were marked out.  Once in position this really looked good.   I used the same soft pencil to darken the round notches I made along the waterway as well.   Below you can see how the scuppers inboard turned out.  I made the waterway in two pieces for the gun deck rather than use one long strip that spanned across the whole length.
 

I also prepared the waterway for the poop deck, port and starboard.   This was easy...no scuppers, LOL.   Just make the strip triangular.  Dont worry about trying to make it concave or anything fancy.   
 
Here is a photo.
 

Finally to the outboard side.  No difference here really.   I used those outboard templates we used way back when....remember those.   If you have to shift the template fore and aft a bit to line them up with the inboard scuppers you made on the opposite side of the deck/hull its no big deal.   But this template will give you a really good start and can be rested atop the wales.
 

 
I drilled with a small drill bit first and again made the holes larger using the #47 bit.   I cleaned them up a bit and darkened them with a soft pencil.  Once again...no need to drill all the way through and hope you meet the same scupper hole you drilled on the inboard side.  Fake it ...till you make it .....I always say.   I drilled part way through once again.   Make sure you really darken them inside the holes nicely and completely.
 

Dont add the waterway on the fcastle deck yet.   I think it best to drill the hawse holes first.   I will be doing that next me thinks.
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

Yes it is.  That smaller tower was built during WW2.  It was for radar and communications as well as other reasons.   It was then used after the war for using the foghorn and other things.  They removed most of the WW2 features but kept that one.  There was a pill box with guns on that bluff as well.  But that was also removed and they kept it alongside the gift shop for display.   They had a small barracks there as well and command center.   These other buildings are still around mostly and used by the parks dept.   
 
Chuck

Hull Planking, cont. .
It seems like forever since my last post. I had some personal matters to attend to amongst a few other things. Anyway, I'm looking forward to getting things back up to speed.
 
I'm working on a tricky part of the hull planking, those cutouts around the gun ports and sweep port lids. I really had to take my time here in order to avoid re-dos. The reveal around the gun ports is somewhere between 1/64"-1/32". A pillar file comes in really handy. It only cuts on one edge thus allowing for clean corner cuts. https://contenti.com/grobet-extra-narrow-pillar-files I use either a "0" and "2" cut.
 
I haven't done any sanding on the planking and as you can see it's a bit of a mess. The red color is Winsor & Newton "Crimson". In the past I would add a bit of Burnt Umber in order to darken the color. The two colors would often separate which I found to be a pain, so I decided to keep it simple this time around.

Mike

Enjoy your vacation and rest up.
Cheers.

Enjoy your vacation and rest up.
Cheers.

Thank you guys...we leave tomorrow.
 
Yes I am headed out to the north and south fork of Long Island.   Gonna check out some maritime stuff including some museums that have small boat collections.  Still researching that block island Cowhorn.  There is supposed to be a nice one in the museum there.  I will be online using my phone though....me always needs some MSW time....lol.
 
Planking has started...today.
 
The facstle is completed.  Nothing to really add except that I followed the planking scheme provided on the plans.   You can see that here.  You guys may of course change it.  I cut these from a 3/64" sheet following the plans rather than use strips.  There is quite a pronounced curve to these and they are small enough so it wasnt a chore.  I basically traced the plan sheet.  Tweaked and sanded to suit.  I used a #4H pencil to simulate the caulking between the planks.
 
Progress below.  One plank at a time.  The outermost planks are the hardest but not terrible.
 



 

Thank you Jim...
 
I have completed all of the hatches, gratings and partners to be placed on deck.  You have seen how the gratings were made.  The two hatches are pretty similar.  The only difference is they have cover boards rather than gratings within in the coamings.
 
 The photo below shows the laser cut coamings assembled.  There is no need to remove the laser char from the lap joints at the corners.  In fact it probably isnt a good idea at all.  They are precision cut so you end up with a perfectly squared up coaming the correct size.  You can and should sand both sides of the sheet before removing these laser cut parts to clean the char from those sides.  Just glue them up using the same right angle jig provided earlier.   Then sand the char off the top of the completed coaming being careful to keep the round-up consistent. 
 
You can see the smaller hatch completed.  The larger one shows the three cover boards also laser cut waiting to be glued into position.  But this you will also note the ledge created on the inside of the coaming that the cover boards will sit into.  These are laser cut for you and can be glued on the port and starboard insides of the coaming.
 

This photo shows the three coverboards in the coaming.  They are pretty thick, but only so they are flush with the center of the coaming to allow for the round-up.   The round-up along the sides of the coverboards should be sanded flush to the top edge of the coamings along the P & S sides.  I know some folks like to show one or two coverboards off the coaming.  You can do this if you want to.  But then you should sand that roundup into the bottom of the coverboards as well.   But I will show them all in place like the contemporary model.
 

To finish off the hatches...round off the corners using the right angle jig like you did for the gratings.   Trim them down to the top of the deck planking.   The bolts were added using black fishing line in the same way.   The iron ring for handles were made just like those on the lower platforms.  Exactly the same.
 

Also shown in the photo above are the mast and capstan partners.   These are completely laser cut for you.  They have etched lines to show the separate sections.   All you have to do is sand them clean and round off the corners as described earlier for the capstan partners only.  Soften the top edges as well.  Add the fishing line bolts and the eye bolts on the main mast partners.  Now some of these can be glued onto the model.  They are all ready to go so you can start planking the decks.
 
BUT there are a some like the main mast partners and capstan partners that need some extra work.   I will describe that next.   For example the elm pump tubes below the main mast partners and the capstan drum as well.
 
More to follow...but here is a photo with the all of the hatches, coamings and partners simply test positioned on the model.  They are not glued into position yet.   I did however glue the smaller grating and coaming on the forecastle deck in permanently....those are all finished up.  Its getting there!!!
 

That would be so nice but it probably would put the builder at risk of being abused.
 
Anyway....those gratings
 
You will basically get all of the laser cut parts in this chapter.  There are only four hatches with gratings.  They are not very large.   Here are all of the elements needed.  You will get two layers for the jig.   The two layers are glued together to form the jig.
 
You also get a right angle jig which is 3/64" thick.  The thickness is very important.
 
Lets get started.
 

Start with the coamings.   They are laser cut and 1/8" thick.
 
The fore and aft sides are already shaped with the round-up of the deck....or camber as usually described but is an inaccurate term.
 
Use the right angle jig to glue two sides together...dont worry about the laser char just yet.   Then glue the remaining two sides together using the same jig to make a nice right angle.
 

Glue the two right angles together to form the coaming.  Sand the sides clean which are left a bit longer as you can see in order to remove the char and leave a nice bright smooth surface.   Also sand the top sides to clean the char.  You can see the cleaned coaming below.
 
Then you can start working on the grating.  Again just like my other smaller scale grating kits.
 
Insert the laser cut grating strips in the slotted jig.  NO GLUE of course!!!   This is just for alignment.
 
Then start adding the cross battens.  These are glued in position.  They may be too tight as you want a press fit.  So just run the small strips 1/16" x 1/16" through your fingers with some fine sandpaper.  Not much.  Just enough so the battens fit into the slots. see below.  There are seven batten strips and seven laser cut grating strips for three of the hatches.  The fourth is made the same way but is much smaller on the fcastle.
 

When all the strips are glued in position,  remove the grating from the jig.  Snip off the edges as shown below.  Then sand all four edges clean.  Try and not distort the perfect square shape.  In the photo two sides have the ends snipped off.   The smaller hatchway will have fewer battens and more to snip away.  Also sand the top surface clean and smooth.  Once again try and maintain the proper shape with the round-up.  You will know when its all done when the char is cleaned from the laser cut grating strip squares.

The photo below shows the top of the grating and sides all clean and nice and smooth.  It makes a nice grating.  The holes are 1/16" or 2" on the real ship and perfectly in scale.

You should but dont have to sand the bottom side as well.   Here is a look.  The battens are clearly less thick than the grating strips and these are pretty close to actual construction methods.  Or at least the impression of it.
 

And almost done...you will see how nice and tight the grating fits in the coaming.   Dont over sand the edges and you should test the grating in the coaming as you sand the edges.   In fact, the coaming normally has ledges on the port and starboard sides inside the coaming.  These create a ledge that the grating sits on so it doesnt fall through.  You can add those if you like.  But in my case the gratings fit so snug that they were not required.  I simply glued the gratings into the coamings making sure the top of the coaming was flush with the grating.  I sanded it smooth with some 400 grit paper.

The four corners of the coaming are very sharp at this point.  You dont want that.  They should be rounded off.  But they are only rounded off down to the deck level.   That is when you take that same right angle jig and use it.
 
The jig is the same thickness as the planking.   So you can place the coaming into the corner and use a sharp #11 blade to slice away the corner.  Slice it down to the top of the jig only.   You can make a stop cut at the jig level before slicing off the corner.  Then just round off the corner.
 
 
Dont slice off too much.   Just a little bit to round off each corner.
 
To finish it off I drilled three holes with a #76 bit.  I used 20lb black fishing line to simulate the bolts on the top of the coamings.  Three on each side.   They cut flush with the top of the coamings with a sharp blade.
 
All done!!!
 
 
 

Thanks guys...There are a lot of things I could work on next but I am eager to get the decks planked.   So next up I will make all the coaming and gratings down the center line so I can plank around them.   Once that is done I will add the waterway and start on the fun bits.   It should come together rather quickly once I plank the decks.  A quick look at sheet 5 still being tweaked which has all of those details.   
 
 

What a difference some paint makes.   Bulwarks are painted however as usual, I will be applying many more thin coats over the next few weeks as I progress.   
 
Before and after...
 

 

Bulwark planking has finally been completed.  It really wasnt too bad.   You just have to keep plugging away and while making careful cuts between those ports.   All the cracks, gaps and dents were filled and sanded in preparation for painting.
 
The second layer of spirketting was added as well to finish off the bulwarks below the ports.  The top edge was softened or even rounded off.  I dont like to leave a hard edge here.  I used a 1/32" strip the same shape and size as the first layer.  I took the shapes from the plans because this wide 1/2" strip needs to be tapered like the first layer and shaped before you glue it on.  Every model will have slight differences so it will take some time to get it right.     Then the top of the sills were very carefully sanded and the cracks filled there as well.   I was careful not to sand into the top of the spirketting which would ruin the nice continuous run along its top edge.  You can see how bad port sills look now but the surfaces are now smooth and once painted will look really nice.  
 

Before I paint however I needed to add the 4 fixed blocks on the inside of the bulwarks.  On Winnie, I had used laser cut fixed blocks the same thickness as the planking.   You would glue them to the framing before planking and then plank around them.  I went a different way this time.  I just planked the entire interior bulwarks and then just drilled the fixed blocks through from the outboard side.   Then I sanded them clean and reamed them a bit with a round file.  To finish off these simulated fixed blocks I took a very small "V" gauge chisel and made a small simulated sheave slot between the two holes.   Since the bulwarks will be painted this seemed like the better way to go.  You can see the two fixed blocks below at the bow on the starboard side.  I used a sharpened pencil to color the sheave to simulate a more appropriate color.   
 
I have also hi-lighted in this photo how I planked the bow inboard.   I first glued a 1/4" x 3/64" strip down the inboard side below the bowsprit hole.   See the red arrow.  This allows me to push the planking strakes up against it which for me makes the process easier and neater.  There were two more strakes to add on each side of this to plank the bow inboard.   The cracks were filled and it was all sanded smooth for painting.
 

 
Here is a photo showing the aft portion of the bulwarks planked and ready for painting as well.  Note the two fixed blocks here as well. 
 

The one last thing you might notice is that I did in fact add the margin plank all along the bulwarks.  This is 1/4" wide and 3/64" thick.   It finishes it off neatly.   You dont have to add this yet but I find it easier to paint the bulwarks when I have a nice right angle to paint down to.   Hopefully I wont bugger it up and get red paint all over the margin planks.  But if you find it easier to paint the bulwarks first without making a mess then fell free to do it that way.
 
At the bow,  the margin planks on each side were cut from a 3/64" thick sheet of yellow cedar.   I used the plans and planking template provided.  I cut it out and used that paper template as a starting point.   After seeing what I needed to adjust for a tight fit, I transferred this shape to the wood sheet and cut it out with a sharp #11 blade.  If you look at the photo again you can see my first attempt which I discarded.  It didnt fit as nicely as I wanted.   So I made more adjustments and cut another.   You would be best served to buy a few extra 3/64" thick sheets of Yellow cedar for stuff like this.   Every model will be slightly different and you will want to go through this exercise as well for a good fit.   
 

 
I am ready now for painting....the bulwarks will be carefully painted red over the weekend.  Depending on my honey-do list.
 
 

Greetings Fellow Modelers
 
After a busy month with little time for modeling, I've finally begun work on the fish hold of this dragger.
 
 
But first, please allow me a quick diversion.
 
The path of the recent solar eclipse tracked over Maine on a day when there was barely a cloud in the sky.  My wife and I traveled several hours north on country roads to get close to the center of totality.  A total solar eclipse is such an astronomical coincidence that it's hard for me to get my head around it. That from a moving 100-mile diameter shadow on earth, two spheres appear to be the exact same size because one being 400 times larger is 400 times farther away, and that they line up precisely with the smaller sphere blocking all the direct light of the larger while leaving the entirety of its corona visible.  Perhaps I'm a simpleton, but I find this extraordinary.  To be honest, I thought this was going to be an interesting but ho-hum visual event, but when it went dark and I took off the glasses to see where the sun had gone, I was mesmerized.
 
I had a DSLR mounted on a tripod with 200mm of lens.  I promised myself beforehand to enjoy the experience and not spend the few minutes of totality tinkering with camera settings.  So, I preset the camera and hoped for the best - manual focus, aperture priority, exposure bracketing, cable release and crossed fingers.  I pushed the cable release quite a few times without ever looking at the results.  Later, I found most were completely blown out and a few were just terribly overexposed.  But I'm not disappointed.
 

 

 
 
The lens flare image below is my favorite.  A lousy eclipse photo, but an interesting image just the same – kind of surreal.
 

 
 
 
Fish Hold
 
My decision to display the boat with the hatches open and maybe a bunker plate or two, requires that the entirety of the hold be modeled as I can't predict what will be visible through each opening and view angle. Mainly that view will be small fragments of individual bunkers and planked partitions, so this modeling will be on the quick and crude side.
 
Before I started in on that, I first washed the hull exterior with India ink/alcohol to give it a little age. About 2 parts ink out of a hundred. I've yet to decide on how the hull will be painted/weathered, but this small amount of coloring doesn't narrow my options, and the alcohol tends to remove shiny sanding spots and helps to unify the overall look – at least to my eye.
 

 
 
I then penciled on the water line. I placed the hull back onto the base and used a squared scrap of construction lumber with a pencil glued to it.
 

 
 
The fish hold uses up almost 17' (5.1m) of hull length. The area is partitioned off into 20 individual bunkers/pens as shown below in the top-view drawing. The pens with green dots hold the ice/fish and the red dot areas do not. The blue dots are the stationary posts that hold the wood slats which make up the partitioning. The four pens in the center over the keel functions as a walkway but can also be partitioned to hold ice/fish.
 

 
 
Shown below is the lower half-section at station #7. The open space against the side of the hull is the area identified by red dots. This area is empty and begins at the lowest bilge ceiling strake. This drawing detail is actually from the “transverse section” plan sheet of a completely different boat by the same designer a few years prior to the Pelican, but it is labeled as the “type plan” for the Pelican.  Consequently, the dimensioning is incorrect for my boat, but the structural construction is the same – presumably.
 

 
 
The bases for the posts are 6” square timbers and on the model the six center bases are mounted on wood strips that span the entire length of the fish hold. The six bases away from the center are beveled to reflect the changing shape of the hull as it narrows toward the bow. The drawing below shows the bevel for the posts in the area near station 6A.
 

 
And for the posts in the area near station 4A. Note that the bevel has changed due to the base sitting higher up in the hull. This is necessary because the interior space is narrower yet the distance between posts must be maintained.
 

 
I print out spacing guides to locate the center line for the wood strips the post bases will sit on.
 

 
I mark the center line for the inner and outer strips on each station bulkhead.
 

 

 
 
The strips are placed, and the outer post bases are beveled and glue on.
 

 
 
As per the plans, there are three planks below the lowest bilge ceiling strake and below that is concrete. Although they are not yet glued down, the image below shows those three planks in position. The six inner post bases have been added as well as some styrene sheet material to act as a support floor for the “concrete”.  Also, note how the post bases (top of photo) incrementally sit higher from left to right as the hull narrows.
 

 
It would have been easier to place the two lowest bilge ceiling strakes as one piece and mount the post bases on top of that. But, I didn't and decided instead to piece it together around the posts for reasons that in retrospect make absolutely no sense. But that's water under the bridge and in the end it won't show anyway.
 

 

 
 
I smeared on some Hydrocal to form the floor of the main fish pens.
 

 
 
Colored up the bulkhead planking with chalk/alcohol (burnt sienna, raw umber and black).
 

 
 
Made up the grating to place over the keel and gurry trough.
 

 
 
I'll be placing some dim-ish lighting in the hold, so a gloppy PVA mixed with black acrylic paint is slathered onto the hull to prevent light leaks. All of this mess will be hidden by the wood plank partitioning.
 

 

 
Next – posts, partitioning and completing the hold.
 
Thanks for taking a look.  Stay well.
 
Gary

Just a small update...
 
I was eager to get started with the planking of the bulwarks.   There is no trick for this.  Its just a grind of cutting and shaping planks to fit between the ports.   Its a slow process and you must be very neat and keep the cuts around the ports straight etc.
 
The planking is all 3/64" thick.   Just as I did with the Winnie, the two strakes below the the ports (the spirketting) were added first.  The spirketting is normally thicker than the planks above it and stands proud.  I have always accomplished this by planking the spirketting in two layers.  It still amazes me how few kit mfgs even show this feature.  You dont have to do it this way if you dont want to.  You could just use 1/16" or even 5/64" thick planking and do it one layer.   Its up to you.  I will add the second layer of spirketting once the entire side has been planked.  I will use a .025" thick second layer.  
 
Having said this...some notes are in order.   The top of the spirketting is lined up perfectly flush with the bottom of the gun ports and sweep ports.   This is great if you happened to get lucky and they all line up perfectly.   I dont care who is making the model, this is pretty impossible to do.   Even the most skilled builders will need to tweak the bottom sills of each port so they line up perfectly with the top edge of spirketting.  This will become very apparent after you run your planking strip down the inboard bulwarks.   I was very lucky in that most of the ports only needed some minor tweaking.   Some were just a hair too high.  Less than 1/64".   So I used a sharp chisel to  make the ports sits flush along the top of the spirketting.  you can see that in the photo below.  The ports will need a lot of paint touch up which was expected.  Whatever you do,  do not notch out your spirketting to accommodate a port.  Try and keep the top edge of the spirketting a nice continuous run without notching it.  Should one of your ports sit too low...I recommend instead that you add a sliver of wood on top of the port sill to raise it up in line with the spirketting.
 
I hope that makes sense.
 
See below...notice how I did not use any pencil to simulate the seams between each strake.   In fact, just the opposite.   I am painting the bulwarks red so this allowed me to take a small shortcut.  You may want to consider it as well.  I dont want any seams to show at all.  In fact I didnt even have to use two individual strakes for the spirketting.   If you look towards the fcastle bulwark planking you can see the area I havent planked yet.  I used one wide strip of 3/64" thick cedar instead of using two narrower strakes as is typical.  I believe it was around 1/2" wide.  Probably slightly wider on the aft portion.   
 
Then because we know the sweep ports are 3/16" high,  a 3/16" strip was used next and cut between the ports and sweeps.   I was careful to be very neat with these cuts.
 
Finally the remaining planking above the sweep ports would normally consist of two more strakes.   Because I am painting the bulwarks, I once again used ONE wider strip of 3/64" thick cedar so I could quickly fill in those areas in one pass.  It should paint up very nicely.  This reduced the number of neatly cut ends to all those strakes between the ports.   There are fewer seams to keep neat as well.   The photo almost looks like a solid hull because there are few seams showing between strakes.  
 
Now if you are NOT going to paint the bulwarks red....this means you will have to use individual narrow strakes.  It will take many more cuts and trial fittings...repeat and repeat again.  That is your choice.  I will take more pics after the second layer of spirketting is added and after the bulwarks are painted red.  The bow area will be planked with narrower strakes just as they should be.  It will be easier to bend those.   But once the bulwarks are painted red nobody will be able to tell how many strakes you actually used.   So you must make a decision ...to paint or not to paint.  Essentially you can plank what's remaining of the bulwarks with just three rows cedar strips.   The wood package comes with your typical 3/16", 7/32", 1/4" and 9/32" wide planking strips that are narrow, so you will need to buy some 3/64" sheets should you want to plank your bulwarks like I have done here.  Then you can cut some 1/2" wide strips instead.   But only if you will be painting the bulwarks red.
 
 
 
 

Small update, I’ve added the upper laser cut planking panels to the model, these will be the ones used in on the final model, with a few slight modifications that I’ve overlooked but corrected on my model. To begin I placed a board across the beam to ensure the proper height of the panels and I clamped them as I went along, once I was happy with their location I ran a batten underneath both of them to ensure that the planking that will follow below will have a smooth joint and continuity with the laser cut panels, once the panels were tweaked to fit right I then glued them into place using CA.

you can see below that I made some adjustments to the aft panel so the forward one would line up with the gun ports.
You’ll also notice the grey primer, I find this necessary with MDF as it’s super porous and soaked up three coats of solvent based primer. The primer also will not swell the MDF and allows it to be sanded smooth in preparation for whichever red you choose for  your port framing.

The batten ensured that I could set them right back where they belong without losing the correct position. I kept the front one clamped in its location while I glued the stern one, this ensured that there was no lateral movement of the aft panel.

The same process was repeated for the front panel.
 
I also begin the lower wales, you’ll notice the same process where I used a batten I reference to the marks on the bulkheads “W1”. The batten goes on the lower side of the line, once the batten passes the eyeball test then it’s time to start the wales, now the wales on this model are over 1/8” thick so unfortunately they will have to be done in two pieces, the first layer I’m cutting them at .080” with a significant taper in the front to fit the rabbet and allow for another layer to go over it and fit in the rabbet as well.

I’m not really concerned with the length or butt joints of the first layer of planks as they will be covered up, just get a smooth run with tight joints.
Unfortunately I can not proceed any further until I complete the counters, I have a laser cut lower counter that I will be testing soon and from there I will plank the upper counter using the laser cut lower as a guide.


 
I will be off for a month in the Himalayas, hiking to Everest base camp and beyond, so I won’t have any updates until about June, possibly one more before I go but will see.
 
Thanks for looking in.
JJ

I have reached another small milestone.  All of the below deck fittings and cabins are completed.  The gun deck is fully framed as well.   Next up I will start planking the inboard bulwarks.   That should make a huge difference.  
 
I hope to see many of you this weekend at the New London show.   It should be a very enjoyable weekend.   I am looking forward to it.
 







 
 
 
 
 
 
 
 
Chuck

Thanks guys….
 
Yes I have mailed a few.  It depends on the country.  Some countries wont allow first class mail or the cheapest option and only allow priority mail.   It weighs about 9 pounds give or take.
 
I just shipped one to Italy for $99 US shipping.
 
I sent others which were around $85
 
So far the most expensive was $149 but I charge $99 usually so I take the hit if its more.
 
So probably around $99
 
 

Thank You...
 
The cabins on the aft lower platform are completed.   No detailed explanation since they are built exactly like the others.   Each partition wall is built up with two layers glued together.   Then they are detailed with hinges and door handles as required along with any upright timbers 1/8" x 1/8" strips.   Their heights and widths are adjusted to fit under the deck beams etc.   Finally they are assembled and glued into position.
 
Here is the tiny powder and filling rooms completed.  These walls are slightly thicker than the other cabins as was normally the case.  An extra laser cut sheet of parts shows how all the cabins are prepared for you.   They are all numbered and shown on the plans.  I built them in the order that they are numbered.
 

All of the cabins completed.
 


Next up is to complete the remaining deck beams carlings and ledges.
 
 

Thank you for saying...
 
I am trying to set aside time regularly to make a little progress.
 
Continuing with the center line fittings below deck, the WELL was next up.   This is a relatively simple structure.  The four sides are laser cut and etched.  You need to do just a few things before you glue up the four sides.  
 
First...make sure the fore and aft sides sit nicely on the keel.  Once you adjust them as needed,  you can cut the four upright columns to length.   How do you determine the length of these.  The two aft columns are shorter.  These are simply cut to fit under the next deck beam.  No  big deal.   The two columns on the fore side of the well are different and taller.   These two columns are cut so the tops are flush with the TOP of the gun deck beams or carlings.
You will have an opportunity to sand these shorter so dont over sand them initially.

Assembling the well is straight forward after you glue the columns to the port starboard sides of the well ahead of time as shown above.   You can also use some scrap tiny strips of wood to make the toggle handles for the access door.  Then just glue them on.   They are clearly shown on the plans.
 

With the four sides glued up and square...test it on your model.   After any minor tweaks you can glue it position permanently.
 

 
Then the next few gun deck beams, carlings and ledges were taken care of.   Eventually you will get to the beams where the capstan step needs to be built along the center line.  So you will need to stop and assemble the capstan step.   I glued those appropriate deck beams in position so I had a reference point to test fit the step periodically.  The step is also laser cut for you and has a recessed circle in the center.   This will accept the heel of the capstan drum...eventually.
 
The step is bolted to two columns that are set on top of  keel.   These two columns are 1/8" x 1/8" strips just like the other support columns under the beams.   Hopefully you havent forgotten to add any up until now.   They are all shown on the plans.  
 
You must cut the two columns to fit under their respective gun deck beams.   Now you have to determine where along those beams the capstan step will be placed.   You can use the plans of course but it is doubtful it will match your model perfectly.  Mine didnt.   So just understand that the capstan step is slightly higher the lower aft platform and it is level.   Because you know this you can mark the columns for the height of the capstan step with the columns "snug" fit temporarily in position.
 
When I was comfortable that I had the proper height worked out, I was ready to glue it in position.  But first I had to add the simulated bolts on the capstan step.   I used 25 lb black fishing line to simulate these.  And yes the photo shows the step upside down so you can see the hole for the drum.   But rest assured it will be glued in position right-side up!!
 

The capstan step in position...and the carlings added afterwards.
 

And some other views...of the gun deck up to this point with the ledges completed.
 

 


Almost to the other side of the gun deck.  But next up are all of the cabins on the aft lower platform.   Onward and upward as they say!!
 
 
 

I’ve faired most of the hull except for below the wales, the reason is that I want to plank the upper sides and make sure they are stable and epoxied before I turn the model on its side to fair the lower sides, so I’ve faired below the wales a decent amount. The bow and the counters are faired as well.
 
The upper planking where all the moldings and friezes go is laser cut basswood, it has etched reference marks for the QG’s, moldings, fenders and chesstrees. The one you see on the model now is only a test piece and  not the final design. 
 
The lower counter will be a laser cut piece of basswood that will also double as a fairing guide for the counter structure, you can see I used a paper template, I had to make about 6 of them before it finally fit right. So the wood one is coming soon. 


Now for the resin printed QG’s, this was an ambitious project but I thought why not give it a shot and so far I’m quite happy with how they fit. I wanted to attempt this because as I was designing laser files for a two deck QG out of wood, I just felt there were too many ways for it to go wrong if one isn’t careful and spoil the model, thankfully this is going to work and save a lot of trouble.

Now once you fit the QG’s and everything lines up then they need to come off and be finished. You will have to paint them, add the roof tiles, friezes, scraped moldings, windows and a few other decorations and when complete they should be indistinguishable from built up wooden ones. I’ll go into more detail later about how to install them but they will require a little finesse, but not much. 



I have some boxwood on order and will start producing the laser files and testing  for the windows. Also I’m going to begin adding the upper and lower wales, this will be important to get the planking right.
 
Thanks for looking in.
 
JJ

I completed the first ‘set’ of frames that include a gunport.  The frames are for the central port and include the two frames shown in my previous post plus a spacer that is the width of the gunport.  A lot of sanding was done, and of course a lot more will be done when the hull is assembled and the sides are faired.  So far so good.

By the way - does anyone know if the original boat was painted?  The photo in my first post looks like the wales are black.  But if that so - and what about the rest?
I’m trying to decide if I want a model completed in uncolored boxwood or paint it to show how the boat really looked.  Thanks.