Slowhand Posted March 30, 2017 #1 Posted March 30, 2017 Just about ready to apply a finish to my mahogany planked hull. Current candidates teak oil, tung oil or wipe on matte poly urethane varnish. Wipe on poly not commonly available in U.K. Shops, although can get a tin on Amazon. Bit loathe to spend £14 to use as a test coat. Do you think a poly urethane varnish diluted with white spirits would give a good approximation for the real stuff. Should say the strakes have lightened quite a bit since the photo. As an ex chemist not too bothered about the odours although the dockyard failed a recent safety inspection by the Rear Admiral. mtaylor, Canute and Seventynet 3 Quote Slowhand, Current build - Polacca scratch build from Amati plan previous builds San Martin - Occre H.MS Resolution - Corel Half Moon - Corel Dragon keel boat - Billings
Seventynet Posted March 30, 2017 #2 Posted March 30, 2017 Beautiful job on the hull Slowhand! Can you send me a link or a reference to the wipe on matte poly urethane that you mentioned? I have looked in vain many times in the past for a wipe on poly that's actually matte and not just satin. Thanks, Ian Canute and mtaylor 2 Quote Builds in progress - Speedwell - by Syren Ship Model Company Builds completed - Hayling Hoy - by David Antscherl - Naval Cutter Cheerful - by Syren Ship Model Company - Cape Cod Catboat - by Bluejacket - Gokstad - by Dusek - Ship's Boat - by Dusek - Brazzera - by MarisStella
Slowhand Posted March 30, 2017 Author #3 Posted March 30, 2017 Ian, This is all I could find but it's not a wipe on. Because I've already stained the strakes with coloured Danish need to be sure that any further coats don't make them gloss whilst hull is matte or even satin.http://www.homedepot.com/p/Varathane-1-qt-Matte-Soft-Touch-Polyurethane-266233/203331997 Sent from my iPad mtaylor, Canute and Seventynet 3 Quote Slowhand, Current build - Polacca scratch build from Amati plan previous builds San Martin - Occre H.MS Resolution - Corel Half Moon - Corel Dragon keel boat - Billings
Seventynet Posted March 30, 2017 #4 Posted March 30, 2017 Thanks for looking that up. Good luck with your fine build. Ian mtaylor and Canute 2 Quote Builds in progress - Speedwell - by Syren Ship Model Company Builds completed - Hayling Hoy - by David Antscherl - Naval Cutter Cheerful - by Syren Ship Model Company - Cape Cod Catboat - by Bluejacket - Gokstad - by Dusek - Ship's Boat - by Dusek - Brazzera - by MarisStella
Seventynet Posted March 30, 2017 #5 Posted March 30, 2017 So 50:50 mineral oil to oil based satin WOP will give you matte? I can't promise I won't do something idiotic but I have oil and water based stuff figured out. 👌 I prefer oil based and have used both. Thanks Spyglass. ian Canute and mtaylor 2 Quote Builds in progress - Speedwell - by Syren Ship Model Company Builds completed - Hayling Hoy - by David Antscherl - Naval Cutter Cheerful - by Syren Ship Model Company - Cape Cod Catboat - by Bluejacket - Gokstad - by Dusek - Ship's Boat - by Dusek - Brazzera - by MarisStella
Landlocked123 Posted March 31, 2017 #6 Posted March 31, 2017 I'm no chemist or finishing expert, but I would think if you tried to mix oil based anything with water the only thing you would get is a mess. John ps Or you can go traditional and use pure beeswax dissolved in turpentine. Chop up the beeswax, cover in the turps and let it dissolve over a couple of days. Adjust the the mixture until you get a thick paste. Wipe on a thin coat and then buff off. Repeat as desired. J. Seventynet, Canute and mtaylor 3 Quote Member: Connecticut Marine Model Society Nautical Research Guild Model Ship World "So we beat on, boats against the current, bourne back ceaselessly into the past" F. Scott Fitzgerald - The Great Gatsby "If at first you don’t succeed.......skydiving is probably not for you”
tkay11 Posted March 31, 2017 #7 Posted March 31, 2017 I've made my own with a third each of linseed oil, mineral spirits and matt polyurethane varnish. Woodworker sites give this mix and say different people use different ratios for their own preferences. Tony Canute, Seventynet and mtaylor 3 Quote === First build: Caldercraft HM Cutter Sherbourne 1763 FINISHED 2nd build: Triton cross-section COMPLETED 3rd build: La Chaloupe Armée / 42ft Armed Longboat of 1834 by tkay11 – scale 1:36, plans by M. Delacroix COMPLETED 4th build: Allège d’Arles 1833 (Ancre) POB by tkay11 – scale 1:100, plans by F. Fissore COMPLETED Working on La Jacinthe 1:96 POB (ANCRE publications)
Slowhand Posted March 31, 2017 Author #8 Posted March 31, 2017 Thanks Spyglass, will try some home made wipe on poly as you suggest. mtaylor and Canute 2 Quote Slowhand, Current build - Polacca scratch build from Amati plan previous builds San Martin - Occre H.MS Resolution - Corel Half Moon - Corel Dragon keel boat - Billings
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.