Jump to content

Suggestions to add depth to wood deck planking


Recommended Posts

That's an awfully nice looking deck, and personally one I would be very happy with as is. That's probably not helpful though. 

 

Have you applied any finish to it so far? If so, I expect that would have to be removed/ sanded out first. Do experiments off model of course, but you might find tung oil would make the colors and the seams a little darker and richer. 

Edited by whitejamest

Current build: HMS Speedy, Vanguard Models 1:64

 

Past Projects: 18th Century Longboat, Model Shipways, 1:48

                         22 Foot Yawl, Vanguard Models, 1:64

Link to comment
Share on other sites

Your choices will depend on your goals and focus. 

From an academic and historical focus and in the realm of wooden sail ,  weathering and "pop" are factors to be avoided.

Glue a series of three or more short strakes of your planking material to a flat piece of scrap as test subjects.

After giving the deck a light scrapping using something like a sharp high quality single edge razor blade and a light 91% alcohol swab,

a coat of 1/2 strength clear shellac (or if you "really" want it darker- garnet shellac).  When dry, a Scotch Brite rub down and a tack rag. 

0000 steel wool works the surface as desired, but the steel fibers that are shed are prone to oxidation and staining the wood and they very difficult to completely remove to avoid this..

Stop here or follow with a rub on coat of full strength.

Make that all of the glue on parts ( hatch comings, bitts, deck houses, etc. are either in place, or their bonding surfaces are masked after scrapping and before the shellac.

 

If you intend to continue with a follow on ship model,  you might read this post Looking for the Correct Sequence and Terminology for Deck Plank Butt Shift

It is a discussion and not a definitive "answer to it" but it servers as a gateway to the deeper aspects hovering over all this.

Edited by Jaager

NRG member 50 years

 

Current:  

NMS

HMS Ajax 1767 - 74-gun 3rd rate - 1:192 POF exploration - works but too intense -no margin for error

HMS Centurion 1732 - 60-gun 4th rate - POF Navall Timber framing

HMS Beagle 1831 refiit  10-gun brig with a small mizzen - POF Navall (ish) Timber framing

The U.S. Ex. Ex. 1838-1842
Flying Fish 1838  pilot schooner - POF framed - ready for stern timbers
Porpose II  1836  brigantine/brig - POF framed - ready for hawse and stern timbers
Vincennes  1825  Sloop-of-War  - POF timbers assembled, need shaping
Peacock  1828  Sloop-of -War  - POF timbers ready for assembly
Sea Gull  1838  pilot schooner - POF timbers ready for assembly
Relief  1835 packet hull USN ship - POF timbers ready for assembly

Other

Portsmouth  1843  Sloop-of-War  - POF timbers ready for assembly
Le Commerce de Marseilles  1788   118 cannons - POF framed

La Renommee 1744 Frigate - POF framed - ready for hawse and stern timbers

 

Link to comment
Share on other sites

Thanks for the input everyone!

 

I definitely did not want a weathered look, but was hoping to darken the seams to get the look of caulking. This is my first wooden ship model, and _after_ I installed the deck planking I found a tip about rubbing the sides of the planks with pencil lead before gluing them down.

 

There is one light coat of wipe-on poly which does produce a very slight amber tint, but the lighting was poor in this photo and it is no where near as yellow as this pic makes it appear.

 

I was thinking a dark wash of some sort might darken the seams a bit.

Link to comment
Share on other sites

I'm not sure you can do the caulking at this point.  Most of us use a #2 pencil or an old black felt tip pen on one edge of the plank.  Many lay in construction paper or even thinner paper.  Or... we don't it at all.  

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...