Jump to content
MORE HANDBOOKS ARE ON THEIR WAY! We will let you know when they get here. ×
Model Machines LLC – Byrnes Model Machines - machines to be back in production soon. ×

Herby63

Members
 View Profile  See their activity

  • Posts

    134

  • Joined

  • Last visited

 Content Type 

Everything posted by Herby63

  1. Herby63
    I took a second chance on soldering the handrails to the front plate as this has to be done on the aft bridge as well. SUCCES this time. In stead of applying the soldering paste to the pins of the handrail, I put the smallest amount on the points on the plate. First I soldered the ends , straightening the brass plate against a steel pin and then, one by one, the other points. (the knife is only for reference) Next I bent and soldered the brackets to the bottom plate. The 2 outside ones are at a 45° angle. Finaly I glued both plates to the Merit bridge, using both yellow (thick) and pink (thin) Zap CA-glue. Until next update, enjoy modelling.
  2. Herby63
    I pimped the merit brackets for the mast stays pith some Pontos parts (Nrs 157 en 158) and attached them to the fore and aft bridges. Then I soldered the brackets (Pontos parts 513 and 514)together and attached them to the sides of the bridges with CA-glue. Until next update, enjoy modelling.
  3. Herby63
    Time for a little update. I drilled out the porthols and glued the messing parts. Then I soldered the doors from the back and glued them with PVA-glue to the bridges (single doors to the front bridge and double doors to the aft bridge). Until next update, enjoy modelling.
  4. Herby63
    Fore bridge: I tried soldering the parts shown in the bottom left corner of the previous picture. The brackets on part 138 went OK. The handrail to part 139 however did not want to stick. I had to clamp down this piece as it was bent due to the etching process. The contact points were so small and the heat could not be applied in such a way that the very small amount of soldering paste woul melt. So i glued the handrails with PVA-glue. The rails to the sides of the bridge I glued too, in order not to mix them up (error in Pontos instructions, numbers are switched). This was not a good Idea. The handrails are easily knocked off when handeling the part. More about that in a future update. Till next update, enjoy modelling.
  5. Herby63
    Fore and aft bridge: I started removing all details that will be replaced by Pontos parts. I also filled some portholes that turned out oblong due to the casting techniques used. Till next update, enjoy modelling.
  6. Herby63
    Steps 20/21: boat decks. I removed the protruding datails of the Merit parts as I did ont the main deck. Then I soldered rigging brachets and boat supports to the baseplates, and finaly used 5 minutes epoxy to glue the brass plates to the plastic base. After curing, I cut the excess glue off. Till next update, enjoy modelling.
  7. Herby63
    Browsing through the manuals I came across the following part for the midsection of the main deck. Pontos parts 29, 352 and 2x 353 are soldered together with a little soldering paste and heat applied from the back. Till next update, enjoy modelling.
  8. Herby63
    Ladder rungs, casemate lids and anchors attached to the sides. Till next update, enjoy modelling.
  9. Herby63
    The Pontos handholds were glued in with PVA-glue nd the Pontos shutters for the 4 rounded casemates were bent, soldered and glued with SloZap. Till next update, enjoy modelling.
  10. Herby63
    I allmost forgot to put Pontos part 364 to the front of part B8. The handholds were removed from the casemate sides , Pontos templates applied, and 0,4 mm holes drilled usong the Tamiya electric handy drill. Till next update, enjoy modelling.
  11. Herby63
    So here come the 2 Pontos reels for the middle deck. I then collected and cleaned up the midship bulckheads for step 16. and finished the day by preparing the casemate sides by filling the recesses for the hinges of the shutters wirt Vallejo putty, leaving them to dry overnight. Till next update, enjoy modelling.
  12. Herby63
    Step 15: deckfurniture of the middle deck. All Merit parts are replaced by Pontos Photo-etch, bent and soldered together. Only the reels remain to be assembled Till next update, enjoy modelling.
  13. Herby63
    I assembled the ventilation shafts from step 14 and jumped to steps 24/25 to finish theremaining ventilation shafts. Those are mounted on the fore funnel base. To finish off step 24 I cleaned the cutters, added the rudders and glued the supports on the cover of the largest cutter. I also replaced part G39 by the Pontos equivalent and glued it together with part G44 on the funnel base, but forgot to take a picture. No doubt it will be seen in future updates. Till next update, enjoy modelling.
  14. Herby63
    Merit Step 13: The bottom parts of the ventilationshafts have been glued together with Tamiya Extra Thin cement. I cleaned up the seams of these parts, scraping with an X-Acto knife, using needle files and medium and fine sandingsticks. According to my humble opinion, a maximum of 10 of the 14 ventilation shafts have "trumpet like" openings. The other four have a ring with crossed half round ribs. According to contemporary pictures that have been coloured, the "trumpet like" tops have red louvres. Although those "trumpet like" tops are present in the Merit kit, they are nowhere mentioned in the manual, and the gratings that are supposed to represent louvres have diagonal holes and bands. In the Pontosset there are round gratings with exactly the right diameter. But these are for the searchlights. However, this gave me an idee. Previously I built the Trumpeter 1/200 Bismarck, with a lot of functions. In this kit there are 8 gratings for 7 searchlights. Those happen to have the same diameter. And I also have a second Bislmarck kit, that I intend to upgrade with a Pontos detailing set to make a very detailed display model. Therefore I have an extra grating. The Pontosset for the Bismarck also contains 8 gratings but those are fully closed. In case I want to install LED's in the searchlights, as I did in the first model, those gratings are not usable, and thus available for Mikasa, giving a perfect illusion of clased louvres. The half round ribs have been glued woth a dash of Pink Zap, and attached to the round tops with PVA-glue. Excess glue is easily removed with a damp brush. Till next update, enjoy modelling.
  15. Herby63
    I assembled and soldered all Pontos parts to replace the plastic parts of step 11. Till next update, enjoy modelling.
  16. Herby63
    Steps 11 and 12, all brass parts glued on ant the slots for the boat supports filled with Vallejo Plastic Putty. Ready for paint. Till next update, enjoy modelling.
  17. Herby63
    Now that a considerable number of parts have been detached and collecte into numbered boxes, it's time to start assembly. Merit step 11: cleaned up the plastic parts with file and fine sanding stick. Part B9: drilled out the 6 holes in the sides and chamfered from the underside. I removed the centerpart drilling holes, one next to the other and straightened the edges is with a knife I bent and soldered the Postos boat supports and glued them on part B9 with SloZap. Till next update, enjoy modelling.
  18. Herby63
    Next I collected the Merit parts and Pontos wooden parts for steps 30 to 35 (front and rear bridge), 40 (main guns) an 43 and 44 (funnels). Till next update, enjoy modelling.
  19. Herby63
    I collected the pieces for Merit-steps 11,12,13, 14 and 16 (middle deck furniture), and steps 26 to 29 (details on fore- and aft deck, 46 to 51 and 63 to 66 (mainly small boats), in labeled boxes. Till next update, enjoy modelling.
  20. Herby63
    I used some epoxyfiller on the decks to level out any unevenness caused by removing deckdetails and to fill holes for plastic parts that will be replaced by photo-etch. When cured, I sanded the decks and used some Vallejo Plastic Putty on the remaining small indentations. After sanding, these decks are ready for the painting department. But in order to make the most of setting this up, I am first going to prepare some small parts. Till next update, enjoy modelling.
  21. Herby63
    I cut the main wooden deck parts loose with a fresh X-acto knife. Due to the toughness of the backing, multiple passes are necesary. Untill the next update, enjoy modelling.
  22. Herby63
    Hi Jeff, those are drytransfers. How they are applied, you can see in my Mikasa build log. The advantage is that there is no risk of silver bleed around the decal. I made a first attempt to attach the torpedonets before painting the hull, as the bracings attach to it. I gave up for now, so the problems you encountered are very recognisable to me and I admire the tricks you applied to solve these problems. I shall certainly revisit this part when my build is nearing completion. 😀 I allready have some ideas for the showcase and will reveal them shortly, as installing linghting requires provisions to be made in the base. Kind regards, Herby
  23. Herby63
    Breakwaters on fore and aft barbettes: I filled the slots with putty as I would like the breakwaters to sit a little bit higher than Merit provides for. Then I made a jig for positioning the plastic breakwater at an even distance from the deck. I used a "Kolderstok" plankbender to bend a strip of wood of the apropriate with. I held the strip in place with a lace. I removed the plastic struts, glued the breakwaters in place, and placed the Pontos struts with SloZap. Finaly, I scraped off the outer ring around the barbettes to allow the Pontos wooden deck to lay flush on the plastic deck. Till next time, wishing everyone lots of modeling fun.
  24. Herby63
    I copied the details to be removed from the main deck from the Pontos instructions and removed them with a small chisel in an X-Acto handle and a small jewelers hammer. This went very well and asks for very little aftertreatment with a medium sandingstick. Till next time, enjoy modeling,
  25. Herby63
    I filled the portholes from the inside with Mikro Kristal Klear. The full hull thickness allows for the drop to partialy fill up the hole, without protruding or touching the vertical bars present at some potholes. When drying, it becomes completely transparent. Then I prepared 3 carbonfibre tubes to connect the holes for the anchorchaines at the bow with the holes in the deck. This is to avoid lightblead as I intend to light up the model with some LED's. I enlarged the holes in the deck slightly to allow for the 5 mm tubes to pass through. Then I cut 3 pieces of tube, 14 mm long. Then I beveled?? the tubes at the underside to fit to the hull, and glued them in the deckopenings with some SloZap. I reinforced the joints at the underside of the deck. And finaly, I sanded the upper parts of these tubes flush with the deck. That's all for now folks, See you next time.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...