Jump to content
MSW Spring Donation Drive

Herby63

Members
 View Profile  See their activity

  • Posts

    95

  • Joined

  • Last visited

 Content Type 

Everything posted by Herby63

  1. Herby63
    I assembled the stern achors with the Merit and the pontos parts, and glued them to the hull, under the stern walkway, with SloZap. Wishing everyone lots of modeling fun.
  2. Herby63
    Thanks for the nice worde, Javlin, and thanks to all the folowers for clicking the like-button . Before mounting the torpedonet booms, I assembled and placed the 15' booms for protecting the propellers. I used a "holderdowner" as Ron Calverley has demonstrated so often in his Youtube series "The Model Ship" to hold the piece in place while the glue was drying. Wishing everyone lots of modeling fun.
  3. Herby63
    The torpedonet booms on the starboard side will be mounted in the "net not installed" position, and on the port side in the "net installed" position. So I soldered 8 pieces 721, 725 and 726 to the ends of brass turned parts 23 and glued 8 stainless steel hooks (Pontos 51) with SloZAP in the hole at the other end of the booms. To get an impression, I positioned them in the eyepolts and against the catwalks. The parts for the port side collected, bent and positioned on the booms, ready for soldering. Brass parts (721, 725 en 724) soldered to the ends of turned Brass part 23 . I drilled out the holes in the other end a little bit deeper (0,4 mm drill) so that the stainless steel hooks could be glued in a lttle bit deeper. I removed the parts of the casematshutters that fold down and filled the recesses for the hinges with some putty. I degreased the torpedonetbooms with IPA and primed them with VMS Metal Prep 4K. Wishing everyone a Merry Chrismas, a Happy Newyear and lots of modeling fun.
  4. Herby63
    I positioned the catwalks on the starboard side of the hull. (between the 2 red arrows) And then I glued them with pink ZAP, holding them temporarily in place with a piece of tape, where needed. The struts received a dash of yello ZAP. And finaly I replaced the downward folding parts of the casemateshutters, because they rest on these catwalks. Wishing everyone lots of modeling fun.
  5. Herby63
    All the segments of the catwalk have now received the supports. Wishing everyone lots of modeling fun.
  6. Herby63
    A carwalk runs alongside almost the full length of the hull. I did not manage to solder the supports to the white metal grills, the solder just turned into tiny beads if tin that would not adhere to the piece, so I switched to PVA-glue. Here the grills 54, 55 and 56 have received their supports and those for grill 57 are waiting to be attached. Wishing everyone lots of modeling fun.
  7. Herby63
    16 more brackets assembled and glued to the hull. Wishing everyone lots of modeling fun.
  8. Herby63
    I made up some brackets and attached them to the hull with SloZap above and below the front casemates (both sides). (Pontos parts 354, 603+607+606 and 366/367)
  9. Herby63
    Hi Scott. I was a bit worried about my soldering skills too, with my +40 years old soldering iron, ad resin-core solder, that oly allowed me to solder things using far too much solder. So I invested in a new soldering station with adaptable temperature, and soldering paste in a seringe. I try to apply the smallest amount of soldering paste, using a small brush. Works quite well. The video's by Captain Slog (Plunging fire scale modeling) are a big help too.
  10. Herby63
    The admiral's walk: The Pontos-instructions Baseplates 213 and 214 soldered together, and topped by part 205. Bent the railing (part 215) to fit the handrail (part 202) By the way, the Pontos-instruction is correct, I avoided mixing parts 205 and 202 up by cutting 205 loose and fitting it first, and only then I cut 202 loose and fitted it to part 215. 202 is slightly longer then 205. Next I soldered the railing to part 205 on the walkway. Then I bent and soldered the 2 halfround platforms to the bottom. After bending the nameplate to the correct curve, I soldered this to the railing. Finaly I soldered the 9 supports to the bottom. A testfit results in this image, whuch is quite pleasing to me
  11. Herby63
    In order to save som place , I plan to deploy the torpedonets on the portside, but to attach the booms to thull on the starboard side.
  12. Herby63
    Next step was to bend and solder the 16 eyebolts (part 53) and glue them and the ring (52) with a little SloZAP in the holes in the hull. The booms for the anti-torpedo-net will be hooked in them. Wishing everyone lots of modellingfun.
  13. Herby63
    Next I drilled 2 4mm holes in the bottom of the hul and attached it to a temporary bottomplate in order to diminuish the risk of damaging the added detail when handeling the ship. Wishing everyone lots of modellingfun.
  14. Herby63
    Next I bent and glued on the shutters for the 2 outer casemates. (both sides) Wishing everyone lots of modellingfun.
  15. Herby63
    Next I bent and glued on the shutters for the 3 central casemates. Wishing everyone lots of modellingfun.
  16. Herby63
    Next I bent and glued on the shutters for the front and stern casemates with SloZAP and the hand holds wit a dash of PVA-glue. Wishing everyone lots of modellingfun.
  17. Herby63
    I testfitted the 6" and 3" guns in the casemates of the hull. I had to enlarge the pivoting holes in the 6" guns slightly to alowe the pins to go in smoothly, as I am a bit reluctant to hammer them in when the hull is laden with PE. The Pontos 3" guns don't fit under the roofs of the casemates, as the bottom plates I installed dont alowe for sliding them in sideways, so I removed the roofs, planning to top the area later with a piece of styrene. Wishing everyone lots of modellingfun.
  18. Herby63
    Some more hull details added, the first with diluted PVA-glue, the doors themselves witg a touch of SloZAP. Wishing everyone lots of modellingfun.
  19. Herby63
    Next are the 47 mm guns: First I soldered the pedestalls (Brass 07B and Brass 08B) to the botom plates (781), and bent the platforms (149) into shape Then I soldered the pre-bent brackets (782) to the pedestalls and the barrels (Brass 07A and Brass 08A) to the pre-bent breeches (783). Finaly I soldered the guns to the pedestall brackets and glued the guns with the small pedestalls to the platforms. Lots of Modelling fun
  20. Herby63
    Mass production of the 3" guns, 1 down 15 to go. Here are some pictures of the different steps. Pedestalls soldered to the bottom plate and brass parts bent to form boxes Brass parts soldered to the pedestall Preparations for installing the recoilcylinders Brass plates bent over the barrels and installed onto the bracket (all soldered), and finaly glued the little box to the side of the barrel with a little CA-glue. Happy modelling,
  21. Herby63
    Time to have a go at a first 3" gun A The composing elements on the left - The pieces, bent where nece"ssary And the result of 3 hours of modellingfun ! Next picture shows the "briliant" Pontosinstructions, and the endresult in the black oval. Happy modelling,
  22. Herby63
    I made to fit a styrene plate and glued it under the kasemates openings at stern and stem in order to prevent these guns from falling in the hull. A 2 mm-hole in the styrene should help lodgeing the base of the guns. happy modelling,
  23. Herby63
    Hi Jölle, I'll try to make the build log as interesting as the model
  24. Herby63
    Next is collecting all the brass parts to make the 3" huns and the 47 mm guns, which replace the Merit parts entirely. Lots of modellingfun
  25. Herby63
    The 6" guns in Merit step 3 are entirely replaced by Pontos brass. They are soldered together, no glue used at all. Happy modelling,

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...