tkay11 Posted October 18, 2016 #1 Posted October 18, 2016 Just a quickie: am I right in assuming that the height of the carlings is about half the height of the beams, and that the height of the ledges is about half that of the carlings? (I'm working on the lower deck, but assume the dimensions would be the same for the gun deck). It's just that I can't see any heights referred to in the plans, and I thought I'd better make sure! If you want to give me the dimensions in full scale inches, that's ok as well! Thanks in advance for any input. Tony Canute, mtaylor and yamsterman 3 === First build: Caldercraft HM Cutter Sherbourne 1763 FINISHED 2nd build: Triton cross-section COMPLETED 3rd build: La Chaloupe Armée / 42ft Armed Longboat of 1834 by tkay11 – scale 1:36, plans by M. Delacroix COMPLETED 4th build: Allège d’Arles 1833 (Ancre) POB by tkay11 – scale 1:100, plans by F. Fissore COMPLETED Working on La Jacinthe 1:96 POB (ANCRE publications)
mtaylor Posted October 18, 2016 #2 Posted October 18, 2016 I think you're right on the dimension. As I recall, most of us just matched the drawings for dimensions. tkay11 and Canute 2 Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
tkay11 Posted October 18, 2016 Author #3 Posted October 18, 2016 Thanks, Mark. I also use the drawings direct from the pdfs when cutting, but I just can't see where on the drawings the carlings and ledges are shown in cross-section, i.e. height or depth. I can see length and breadth, but not height. So I assumed half the beam height for carlings (about 2mm) and half the carling height for ledges (about 1mm). I can't see that it matters, but thought I'd ask just in case there is a 'correct' answer. Tony mtaylor and Canute 2 === First build: Caldercraft HM Cutter Sherbourne 1763 FINISHED 2nd build: Triton cross-section COMPLETED 3rd build: La Chaloupe Armée / 42ft Armed Longboat of 1834 by tkay11 – scale 1:36, plans by M. Delacroix COMPLETED 4th build: Allège d’Arles 1833 (Ancre) POB by tkay11 – scale 1:100, plans by F. Fissore COMPLETED Working on La Jacinthe 1:96 POB (ANCRE publications)
mtaylor Posted October 18, 2016 #4 Posted October 18, 2016 Look at the other build logs then would be my advise. I hope you can get an answer. You might also ask this in the Building, Framing area. Canute and tkay11 2 Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
tkay11 Posted October 18, 2016 Author #5 Posted October 18, 2016 Thanks again, Mark. I think I'll just go with the half and half idea. I have a feeling I'm being far too obsessional! Tony Canute, Dubz and mtaylor 3 === First build: Caldercraft HM Cutter Sherbourne 1763 FINISHED 2nd build: Triton cross-section COMPLETED 3rd build: La Chaloupe Armée / 42ft Armed Longboat of 1834 by tkay11 – scale 1:36, plans by M. Delacroix COMPLETED 4th build: Allège d’Arles 1833 (Ancre) POB by tkay11 – scale 1:100, plans by F. Fissore COMPLETED Working on La Jacinthe 1:96 POB (ANCRE publications)
Recommended Posts