Jump to content

threebs

Members
  • Content Count

    69
  • Joined

  • Last visited

About threebs

  • Birthday 03/28/1956

Contact Methods

  • Skype
    greg.baumgartner2

Profile Information

  • Gender
    Male
  • Location
    Vail, AZ
  • Interests
    Science fiction novels, Bonsai, long distance rifle target shooting ( 600 to 1000 yards) Practicing with my 9mm pistols.

Recent Profile Visitors

113 profile views
  1. As much as I appreciate the "likes" i get on my posts they are just not the same a a personal "atta boy" post I can actually read and enjoy. Might as well have a robot on the other end making generic comments about my work, The whole concept of "likeing" simply escapes me.
  2. These plastic side hinge pin pieces should be the last bits to glue onto the gun doors. That is 4 each for the 32 double doors and two each for the 34 snigle doors, you do the math, I would be to intimidated if I actually knew how many it was, lol!
  3. These plastic side hinge pin pieces should be the last bits to glue onto the gun doors. That is 4 each for the 32 double doors and two each for the 34 sigle doors, you do the math, I would be to intimidated if I actually knew how many it was, lol!
  4. I have a little build station on an end table next to my couch where I sit with my leg up. I constructed all of the half doors and the hinge straps from here. I super glued all the straps to all the doors, then soldered the hinge pins to the the ends of the straps. The heat melted most of the straps off ans I had to re glue almost all of them over. I Used a fresh bottle of super glue and they do stay on better than before. The last photo shows the straps with pins soldered on, after the heat melted the glue.
  5. I will have more time to work on the ship now, I broke my ankle 3 days ago, lol. Surgery in 2 days. I chased a dog running in traffic to a house about a mile from me, I let him in the gate, he had dug a huge hole under the gate, so I put a couple head sized rocks in the hole, but, it looked like he could still get out, so I went to the front of the house and got a big 100 pound rock and as I was rounding the corner I stumbled on a drip irrigation line. I drop the rock to keep from going face first into the iron rail side fence, and, pow, landed on my ankle. I will still help dogs get home though, life happens, and you deal with, move on.
  6. A new build from yours truly. This will be slow to start off as I still have a long ways to go no my USS Columbus, but, I hope to have the hull planked on one side by April of 2018. As you may know, during the civil war, the Pennsylvania, the Columbus, the United States and I believe a few smaller ships were burned to keep them from the Confederacy that was advancing on Norfolk Harbor where they were berthed. These builds are a sort of commemoration of that event. I hope to have all of the ships burned modeled before I die. I then plan on donating them to the Museum at Norfolk if they will take them.
  7. I get more responses on my other build site than I do here, so that one gets more attention. Starting the bulkheads for my USS United States now, just working out how to cut the keel bulkhead. There will be a new site for that build, although it will not get much posting as I will only work on it occasionally until this build is done.
  8. Yeah, but, I post to another build site and the photos post much smaller, you click on them to get a larger print. On this site the "blow up" is the same size as the posted photo. Perhaps I need to reduce the pixels on this site, Just a little more work is all, lol.
  9. Some rough soldering of upper chains they need some smothing with a dremel tool and then paint. The chains need some straightening as well. Let me know your thoughts?
  10. I was looking at the top half of the chain connected to the dead eyes, and I don't think it is square stock like in the photo of the side of the Constitution's hull. I think the blue Print view shows a side on view of another link of chain, a skinny oval like on the Pennsylvania. The way it attaches to the bottom chain link and the Dead eye just does not look like it would work What do you guys think?
  11. been working on deadeyes and chain. the bones had to be cut down 3/16 of an inch and resoldered, now I need to file them smooth and paint them. 'I did a simple twist of copper wire around the deadeyes, soldered them and drilled the holes by hand. The loop chain are 1/2" long and also soldered at ends and hand drilled holes. There is one more section of chain, but, it is just square stock. I am going to cut sown stick pins for the "bolts". I am also putting the rudder on and smoothing out the copper tape where it peeld back from handling.
  12. Small setback, my ships wheel assembly got knocked to the carpet, and, well, my dachunds think anything I drop is food, so...... one wheel got crunched before I could get it away from the dog, lol dont know how to delete this photo
  13. I thought the spar deck furniture would be a snap, forgot about redoing ships wheel from 8 spokes to 10, Five trys to finally get them all roughly the same length and spaced around the outer wheel. I have the binnacle done too. Also the ships bell tower and the hatch behind the stove pipe covered. Working on railing for steps coming off the quarter deck, and the platform and rope ladder fron the wale steps, over the wale cap and down to the deck, which is just a rope ladder. Also the rope railings on the ladders I do not have enough brass posts to "fence" off the Main hatch. Might leave it off like I did on the Pennsylvania.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to provide support to our members in their efforts to raise the quality of their model shipcraft.

The Nautical Research Guild puts on ship modeling seminars, yearly conferences, and juried competitions. We publish books on ship modeling techniques as well as our world-renowned quarterly magazine, The Nautical Research Journal, whose pages are full of articles by master ship modelers who show you how they build those exquisite details on their models, and by maritime historians who show you what details to build.

Our Emblem

Modelshipworld - Advancing Ship Modeling through Research
×