NMBROOK

Things are getting interesting now    I have tack glued some temporary stringers to keep all the frames plumb and true and placed a couple of key braces to keep things following the centreline.I had come up with a fancy jig design but sacked that as to be honest it was unnecessary and would only restrict access.The hull was then infilled from the gun deck upwards partway using Obechi simply because it is easy to sand and shape and the local modelshop happened to have some 1/4 inch sheets..These followed the shear,but the tops were then trimmed down so that they a parallel to the waterline below the top of the first upperwale.I won't call this a chainwale as the channels sit above this according to photos of the builders model.Some extensive draughting was required to sort theTransom side timbers as there is no frame here in Euromodels design,simply fresh air.The transom is still a flat block as this permits easy measuring and marking out.There is a 10mm arc in the transom face which will be added later,but is why there doesn't appear to any overhang of the stern counter at the moment.I want to fill the gaps between the frames to coincide with the top edge of the upper wale.The futtocks would have in reality finished lower down,but I am doing this for asthetics and then there won't be unsightly holes.The visible section of the upperframes and gunport linings will be in Pear to provide an interesting contrast to the boxwood.The 'combs' that provide an anchor for the upperframe sections and fill the gaps I chose to make from European boxwood to further highlight this detail.Rectangles that are horizontal and follow the centreline were cut form box making sure there was enough material to allow contouring to the hull lines later.These were then milled on the MF70 with 5mm wide slots to accomodate the upper frames.The slots are deep enough to ensure the base of the frames lie below the top of the wale and the top of the blocks are high enough to go above it.The idea being that once they are all in place,temporary wales will be attached and the shear marked and trimmed on the top of the combs.The rectangular blocks had the bulk stock removed after milling prior to gluing in place.Final shaping will be done when they are all inplace.I am concentrating on the aft section of one side as there is a temporary upright holding things true at the stern.When this section is complete,I can fit another upright the otherside of the centreline then remove the existing one.This will give me the access to work on the inside of the hull at the inside.I am trying to avoid fitting the transom framing until later as it will make sanding the inside much more awkward.
 
Kind Regards
 
Nigel

Ok update time After sorting the remaining deck supports I preceeded to mark the subdeck out on a piece of 1/16th ply.After cutting out,I began to establish the deck beam positions in order to mark where plank butts treenails etc would be.Refering to 'Restoration Warship',Richard Ensor states that common practice was to have one deck beam central to each gunport and one inbetween.I drew out the gunport positions of the gundeck and marked the beams then marked the other beams halfway inbetween.This design is completely different to that portrayed on the plans,sorry Euromodels but the internal structure just doesn't ring true.Yes I am still working to the plans for the internal layout,just not the beam placement.Another issue came to light in the fact that the long grating and main mast resulted in 5 consecutive beams being split.There is no way this would happen,so I have shortened the gratings to allow two beams to run right through,hence the deck infill at each end.After one or two trial runs and a little trimming,making sure nothing was tight on the pear frames,the deck was glued in place.I did remove the temporary ties across the frame tops to allow this and the deck had to be bent ALOT to get it to 'spring' in.There is still lots of shaping to do to the lower hull especially the stern which is simply a block at the moment.Thorough checks on symmetry will be carried out as the work progresses. 
 
Kind Regards
 
Nigel

Ok something in a way of an update.The infill has been faired although the final touches will be applied after fitting the false deck and bow/stern blocks.The deck stringers have been fitted.The two scrap pieces screwed down provide temporary clamping due to the sheer on these stringers.Next job is finishing the deck edge supports from amidships to bow and the bow/stern filler pieces.Not much more to add that the pics don't explain.
 
Kind Regards
 
Nigel

I have decided to give myself a short break from the small fiddly stuff on my Caroline build and take up where I left off with this.I am continuing on with infilling the hull with limewood.The sections are cut from 20mm sheet.Not much to show,but work shall be continuing on over the next week or two.As I mentioned earlier the bulkheads have been altered to use 1.5mm single planking.The wales will be 3mm ebony,but I am considering splicing the planks at the waterline,ebony above and box below.I do not want to use holly or maple for the 'whitestuff' because I will already have pear,box and ebony and I personally feel that is enough colour variation,any more and it will be too much.
 
Kind Regards
 
Nigel

Hi Sjors
I have changed the bulkheads to make it easier for me later to produce the feature I want.I have taken a picture of a Navy Board model to show you what I mean.If you look where my 'Arrow' is pointing you will see that the hull frames are left open between the upper wales.This is the feature I want to replicate.I would have had to chop pieces of the plywood away later using the full kit bulkhead but replacing them now is easier.If it wasn't for this 'detail' I could have kept the bulkheads as they were.This is also the reason I have changed to single planking,I had worked out how to do it with double planking but it was just making the job complicated.Please feel free to ask all the questions you like.
Kind Regards Nigel
 
P.s.I have a large supply of the clamps,I could do you a special deal      

Ok then,I thought I would take the opportunity of waiting for glue to dry and upload some more pics.
I was not happy with my original strategy for the topsides as I thought in the long run it would be more work.The tops of the bulkheads have been replaced with solid Pear to a more authentic profile.These can be integrated in the topside framing detail,whereas the ply would have needed replacing later.The ply deck beams were inconsequential,I only left them in place as temporary braces.An authentic deck construction will be used gun deck upwards when I get to that stage.These pear extensions have been fitted with brass dowels epoxied in.The extensions have also been tweeked to allow for single planking.The remaining section of the bulkheads have been 'banded' with 1.5mm lime strip to compensate for single planking.I have incorporated a small section of orlop deck in front of the mizzen step as a ladder runs down here.There is also one right at the bow which will result in a significant amount of work in this area.I am leaving this until the 'donkey' work is complete on the rest of the hull as it will involve removing considerable amounts of material from the false keel.As you may have noticed the lower hull is filled with limewood.This is to provide substantial support to the single planking and is a good aid as this is one of the most complex shaped hulls I have worked on.The area where the pear frames meet the deck is a crucial point.The sheer on the outer edge has to be perfect as everything will be measured from here.This is the reason for setting 6mm lime sections in around the perimeter.It ensures the ply subdeck will conform to exactly the right profile.One section is clamped in place while the glue dries.I have clamps ranging from 20p up to £95 but sometimes the easiest solutions are the best    
Kind Regards Nigel

I am going to try and get technical now and provide text with each picture  
The first step is to copy the drawings regarding the bulkheads.This is due to the between deck areas not be cut out from the factory.These were pasted to the relevant bulkheads to allow cutting out with the scrollsaw.Some areas were not shown,mainly the first and last bulkhead which will require some drafting to get the cutouts.

The design of the kit intends for a 3mm by 7mm stringer to be fitted each side of the hull.This stringer does not coincide with anything and to a certain extent will be in my way,so the bulkhead notches were filled with scrap timber.

These are pictures of the skeleton so far.You will notice I have cut my own notches out on the lower deck.These are for 5mm square stringers supplied by me.These provide support for the lower gundeck,which is the only deck that will have a plywood subdeck.The plywood additions to the structure are to incorporate dimensional stability and resistance to twisting.The triangle design makes the skeleton rigid,it is impossible to twist it for and aft.The lower hull will be infilled with lime wood.This triangular structure reduces the wood required and also prevents any distortion that can occur due to the moisture from the glue when fitting the infill.                                                                                                                                                                                                                  
That brings things up to date for the time being.
Kind Regards Nigel

As I am organised for a change,I can provide pics of the box contents including one of the rather substantial exemplary drawings.The only thing not pictured is the false keel,one sheet of laser cut ply,a few assorted laser cut items and some blocks of wood.There is not massive amounts of laser cut plywood parts like other manufacturers,it is down to the builder to fashion parts from solid wood
Kind Regards Nigel

As work is moving well on the construction of my Caroline build,preliminary work is now starting on my next'bill paying' project.This is based on the Euromodel kit,but it is my intention to push the boundaries of what can be achieved with a kit.I shall be using construction techniques for the hull that have been developed by myself,specifically for this build.The completed model shall include the following details;
1/hull planking in boxwood and ebony
2/hull planking omitted between the upper wales with false boxwood frames,this is a feature on quite a few Navy board models which I am quite fond of and an alternative from a fully framed build.
3/Full hull interior,lower gun deck upwards,with planking sections omitted on the upper decks for viewing the interior.
4/Remodelling of the stern to replicate the drawing by Van de Velde the Elder.
This project will be a 'slow burn' until Caroline is finished,but I am starting this log now to avoid missing anything as work progresses.I am trying to avoid starting another log with a planked hull  
Some photos to wet your appetite

The box,rather heavy,given it's size

Mordaunt by Van de Velde the elder
 
Kind Regards Nigel

This is my machine. All homemade from parts.
 

 

 
 
AL

Great work Mij and some nice carving    
 
Kind Regards
 
Nigel

Thanks for the support and the likes...
 
Minor milestone... took the big pieces of wood and made about 850 small pieces of wood.  Oh... and sawdust. 
 
I've closed the sawpits for now and the pieces have been sent to the yard for gluing up into frame blanks and then cutting into frames.
 
Here's pics... and for those who wanted it.. a picture of (naturally) the sawdust from cutting the pieces.
 

 
Hopefully, I didn't mis-count but I still have some "big" pieces left just in case.
 

 
Now where did I stash that really large bottle of glue??
 

I was not happy with the carving of the first eagle, so I carved another one from Boxwood.
 
I cut out the shape of the eagle first, then started the carving.
 

 
I took Antony`s advice in putting a light stain on the carving to bring out the detail.
 
I used French polish and linseed oil.
 

 
Carving with the stain on.
 

 
Eagle fitted to the stern of the ship.
 

Milling the sides of the gun carriages
 

 

 

 

 
Drilling the holes for the 4mm blocks for the carriages
 

 

 
Turning a step suport
 

 
New carving of a rabbit
 

 
Model so far
 

While working on the next batch of guns, I decided to make the lower main capstan, the first of three capstans that will be done. As with the other deck items, I chose to make the capstan from boxwood strip and sheet. It was a very enjoyable piece to make, with the exception of the 16 tiny chocks that had to be individually fitted between the whelps. Very fiddly work, but satisfying to get it done.
 
The guns are well along and should be mounted and rigged in the next few days.
 
Bob

iron armrest -braccıolo in ferro

more photos 2

more photos 2

more photos

More of my work

Looking good mate   Personally I would say yes to a canvas collar over the hole in the deck.I know Caroline has one (according to the AOS book anyway)but I would think this would be common practice otherwise a ton of water would poor in,in rough conditions and decks awash.
 
Kind Regards
 
Nigel

Wouldn't mind seeing that bow filler Jim, as it sounds like a good idea, 'cos the inside edges of our two left/right side of centre line planks will seem to continue into the margin in that area.. this kinda bugged me a little (of course this wouldn't happen if we used a central deck plank  )
Question.. The hole where the rudder comes up through the hull and above the deck ! do you have any idea if this area is left open ? or is there a kind of 'canvas' collar there to stop water going down? (I will be putting a 'collar' on the lower part where the rudder enters the hull from below, but from the deck side I've no idea)
 
All The Best
 
Eamonn

Ok update time After sorting the remaining deck supports I preceeded to mark the subdeck out on a piece of 1/16th ply.After cutting out,I began to establish the deck beam positions in order to mark where plank butts treenails etc would be.Refering to 'Restoration Warship',Richard Ensor states that common practice was to have one deck beam central to each gunport and one inbetween.I drew out the gunport positions of the gundeck and marked the beams then marked the other beams halfway inbetween.This design is completely different to that portrayed on the plans,sorry Euromodels but the internal structure just doesn't ring true.Yes I am still working to the plans for the internal layout,just not the beam placement.Another issue came to light in the fact that the long grating and main mast resulted in 5 consecutive beams being split.There is no way this would happen,so I have shortened the gratings to allow two beams to run right through,hence the deck infill at each end.After one or two trial runs and a little trimming,making sure nothing was tight on the pear frames,the deck was glued in place.I did remove the temporary ties across the frame tops to allow this and the deck had to be bent ALOT to get it to 'spring' in.There is still lots of shaping to do to the lower hull especially the stern which is simply a block at the moment.Thorough checks on symmetry will be carried out as the work progresses. 
 
Kind Regards
 
Nigel

Thanks fellas!
Cheers Frank, you know I'm a fan of your painting style! 
Max, go for it, it's a great subject and to be able to look and learn about the real ship is a real treat. Consider Billings, it has some tweaks you need to do like the gunports, but it has a good shape and the sculptures are not bad. You will have to bend and reshape them alot to get a good fit so plastic sculptures are a real advantage.
Nigel, thanks for your exorbitant comment!  No, no swivels mate. They where never delivered for the real Vasa so I'm not adding them either.
 
 
/Matti

Jeez How did I miss that log!! Thanks for the heads-up and the link Jason.. roll on tomorrow (good grief I'm starting to get enthusiastic about joggling.. this is just so wrong )
Was rocking back and forth in a corner whilst muttering to myself about joggling yesterday, that probably explains why I didn't get it done..     
Thanks for the visit Jason and thanks to all the other Helpers and Likes.  Thanks Folks!
 
Sail 'er Easy,
 
Eamonn