PRS Posted March 21, 2021 Author #31 Posted March 21, 2021 Started on making masts and could not find the bottom pieces. Quick design and print on the 3d printer solved the issue. FrankWouts and Ryland Craze 2 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
BeeWee Posted March 21, 2021 #32 Posted March 21, 2021 Question for you. When you cut the sanctions that fit on the sides what did you use to cut them? FrankWouts 1 Quote
BeeWee Posted March 21, 2021 #33 Posted March 21, 2021 Question for you. When you cut the sanctions that fit on the sides what did you use to cut them? FrankWouts 1 Quote
PRS Posted March 22, 2021 Author #34 Posted March 22, 2021 On 3/21/2021 at 3:38 PM, BeeWee said: Question for you. When you cut the sanctions that fit on the sides what did you use to cut them? Just a razer saw and then cleaned up with a sanding block. FrankWouts 1 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
PRS Posted March 27, 2021 Author #35 Posted March 27, 2021 Put together the stand that comes with it but am questioning whether it will be stable enough. FrankWouts 1 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
PRS Posted March 27, 2021 Author #36 Posted March 27, 2021 Got my ropewalk and this is a thing or beauty. I tried to do the wrapping by hand and it was difficult to say the least. With the ropewalk it is easy to do an everyone should have one. To do the wrap on the top of the masts I just use a piece of brass wire through the one end. FrankWouts 1 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
PRS Posted March 28, 2021 Author #37 Posted March 28, 2021 Made up a small clamp to hold the blocks while I rig them up. hof00, FrankWouts and Michel L. 3 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
PRS Posted April 4, 2021 Author #38 Posted April 4, 2021 Have some of the rigging done. Learning as I go and have made some mistakes with the knots not staying tight but overall I can live with it since it is my first time doing this. Trying different glues to see what works best for keeping the knots tight. I have settled on a 50/50 water/Modge Podge mix as it gets into the knots good and dries a satin. FrankWouts and bhermann 2 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
PRS Posted April 10, 2021 Author #39 Posted April 10, 2021 So I am finished! I learned a lot of new techniques and had a lot of fun. I think I am hooked. Mistakes made and overcome and even though the instructions were not the best because of the lack of plans I worked through it. Here are the finished pictures. Michel L., hof00, David Lester and 1 other 4 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
bhermann Posted April 10, 2021 #40 Posted April 10, 2021 Very nice model! I like the contrast the veneer makes below the waterline. Thanks for sharing the build. Bob FrankWouts 1 Quote Current build -- MS Bluenose Future build - MS Flying Fish "A ship is safe in harbor, but that's not what ships are for." - William G. T. Shedd
BeeWee Posted May 25, 2021 #41 Posted May 25, 2021 On 3/18/2021 at 2:10 PM, PRS said: OK so that didn't turn out too bad. I might have been better using thread and tying them but I will go with this. Here is where I am at so far with things mounted on the deck. Paul the railing on the aft deck has a cut away which instructions say is 59mm long. Does the cut away face inwards or outwards? Instructions don't really show it. FrankWouts 1 Quote
hof00 Posted May 26, 2021 #42 Posted May 26, 2021 (edited) Hi Chap, Very nice build!! I'm hooked also, I think it's partly due to the scent of the A/L new kit wood.... 🙂 Wot's next? Cheers....HOF. Edited May 26, 2021 by hof00 FrankWouts 1 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
PRS Posted May 26, 2021 Author #43 Posted May 26, 2021 22 hours ago, BeeWee said: Paul the railing on the aft deck has a cut away which instructions say is 59mm long. Does the cut away face inwards or outwards? Instructions don't really show it. Not sure which railing you are referring to. The railing at the very rear is curved and only goes one way. I agree the instructions are lacking. FrankWouts 1 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson
FrankWouts Posted July 31, 2021 #44 Posted July 31, 2021 Paul, Just checking your earlier builds and your way of working is even more methodical than mine... Very inspiring, good tips and techniques with beautiful results! Frank. Quote Current builds on MSW: HMS Winchelsea 1:48: Prior builds on MSW: None
(1)(1)(1)(2).thumb.jpg.792ad774561d3d4f35888704cde27a8e.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.