Kevin Kenny
-
Posts
1,395 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by Kevin Kenny
-
We were also careful to get the first plank to give a fatter curve.
- 72 replies
-
- 2
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
We used spacers to flatten the floor boards 1&2 16 feet from the stern.
- 72 replies
-
- 2
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
The angle or the stem was increased to 50 degrees
- 72 replies
-
- 1
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
We tapered the stem with the top wider than the base which sits on the keel or shell.
- 72 replies
-
- 1
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
Here is the new keel and stem which is 2” longer or 21” which at 3/4” :1ft. Is 28 feet.
- 72 replies
-
- 3
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
Today i start on the finial model, actually model number 4 of the same build. Scratch building a model from a book with limited access to actual measurements and building methods not fully described is bound to causes mistakes. Since the objective of this build was to recreate the fishing boat exactly as it was built I have decided to do it one last time. The book gave detailed materials needed to build a 25 ft pirogue yet the photographs in the book show a 28 ft boat being built. I only discovered this when speaking to Richard Hubbard very late in the build. This explains why we ended up with less ribs than saw in the photographs. So we have prepared a new keel “shell”and stem.
-
Some photographs of the finished boat which i am rebuilding on last time.
- 72 replies
-
- 8
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
Today i start on the finial model, actually model number 4 of the same build. Scratch building a model from a book with limited access to actual measurements and building methods not fully described is bound to causes mistakes. Since the objective of this build was to recreate the fishing boat exactly as it was built I have decided to do it one last time. The book gave detailed materials needed to build a 25 ft pirogue yet the photographs in the book show a 28 ft boat being built. I only discovered this when speaking to Richard Hubbard very late in the build. This explains why we ended up with less ribs than saw in the photographs. So we have prepared a new keel “shell”and stem.
- 72 replies
-
- 1
-
-
- fishing boat
- artisanal fishing boat
- (and 1 more)
-
Swan-Class Sloop by garyb - 1:48
Kevin Kenny replied to garyb's topic in - Build logs for subjects built 1751 - 1800
Chuck is spot on Henry but you can also get in touch with most of us directly. I will be happy to discus anything you wish on WhatsApp, zoom etc. Of course we now have my YouTube video log and the Virtual reality images that Greg has recently published. -
So glad you found Tobago 1677 on Prime. We had such fun making the film. It took 9 years to raise the money to make the documentary, but has not been a financial success. I still have many of the guns used to make the film. Anyway i did not do it to make money, just wanted to record the history which is lost on so many of my countrymen.
-
Its wonderful to see this conversation progress. My only wish is that it was not posted earlier which would have accelerated my learning curve. alan I will continue to use the groves as they help line up the frames. The spacers are an excellent idea which should match the groves That were cut in the keel. Of course you could probably make a keel without cutting the groves to take the ribs. Bruce the ribs went through the building board and were stuck with white glue. Supported by the groves they were very stable which allowed me to sand as aggressively as i wanted. For the fine sanding i did use the Proxxon pen sander which is so gently its like painting with a brush. the PVA mould release was easy to peal off. English said i could use water to clean up but i did not have to. the only change i would make is to draw lines on the building board to space an drill the holes more precisely. I used the mold to determined where to drill these holes and they were not all 100% accurate. i suppose that in time i may not have to use the groves but for now it provides me with a fool proof way of lining up the ribs. With the second one there was no issue of it coming out of the mold. It just came right off.
-
Hi Stuglo not sure if that is your name. i had to go and check what came with my sander. The grits would tend to be on the heavy side as the purpose is to grind the frames into shape. Looking back at the used rolls the smooth ones seem to clog up easily, so i would Recommend 80-180 for the majority with a few smoother ones to do the fine work. The majority of the sanding was done with the large 3” roll but the smaller size was also very usefull.
-
It has long baffled me How many of the great modelers make such superb work boats That service the sailing ships of old. I had made many attempts but always felt that the finial product fell short of the Main ship model. One day i came across A post that suggested that these magnificent miniature boats were made using a mold. I looked everywhere to find a paper or video to help me try but never found a complete process. So i decided to try to develop the process and recorded my work on video. The first one did not pop out of the mold but the second one did. The finial product was great if i may say so myself. Attached are the tree videos on the project. Part 1 Part 2 Part 3
-
Completed the gig and ready for painting then the rudder and cap rail and we are done the second one.
- 256 replies
-
- 12
-
Our Emblem ®
