-
Posts
718 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by Don9of11
-
A piece of safety equipment that I haven't seen mentioned is "hearing protection"; Table saws and similar machines are very noisy and can damage your hearing over time. Safety glasses whether they are goggles, side shields or prescription safety glasses are also very important.
-
I think it looks good Alan. I was looking this over and maybe you have thought about this yourself but here's a suggestion, I was thinking it might be easier to loft the section from the last frame to the blue line then loft the lower section of the stern. Of course that would leave you with a sharp edge which then all you need to do is add a corner radius. I am learning not to spend to much time making it perfect the first time because in the end you need to check it with the diagonal lines and buttock lines as druxey suggest and the lines on the drawing while necessary to start, will not be the lines you actually end up with.
-
I know that my transom lines are not correct. I took my inspiration from Goodwin's, English Man of War pg. 24, top left illustration which shows the disposition of the cant frames. Also, I've been following and studying the HMS Bellona by SJSoane - Scale 1:64, 1760 English 74 gun, as designed, build log and paying special attention to the NMM model of the Bellona and the early stages of the SJSoane's own model where the transom pieces are added. The transom and fashion pieces all curve inward to meet last frame and as Druxey pointed out the contours change rapidly. I simply drew a curve at my water-lines and connected the dots so-to-speak. I made no attempt to do it accurately but simply to illustrate. If you look at the stern view, the corner you refer to I think is going to naturally develop and as Hexnut suggest a variable round will be needed after everything is knitted together. It took me about half-an-hour to produce the stern surface, no lie
-
Alan, I've been giving some thought to your work and not to through a monkey-wrench into your thought process but consider my hasty attempt to produce the stern of my ship. I have produced three images which I hope illustrate my idea. Consider how the transoms are shaped as they come up the stern post and using water-lines connect them. In my images I actually went above the wing transom, stop short of the keel and carried my imaginary transoms to the middle line vs. ending right on the stern post. I know the transoms don't go that far down but I did this to illustrate my idea. I used frame 36 as a guide curve and I have a little gap in my surface-lofts. Is this not what you're trying to achieve?
-
A model shipwright a kit does not make~ This is nice kit and the build logs are awesome but no matter how well the pieces are cut or how nice the kit looks in photos, until they make there way into the hands of the shipwright that's all they are is cut pieces. You mentioned throwing out what you've started, did you begin a HMS Alert build log? I didn't see a link.
-
You're farther along than I am Alan but I given this some thought and here is what I come up with, forgive the crudeness of my sketches : A) lower left, draw in phantom stations (red) after frame 36 making sure they follow the wing and deck transoms and tie everything together at the keel with guide curves, then trim away what you don't need A1) upper right, draw in the counter timbers, wing and deck transoms and then "flesh" it out from there. After the last frame, the ship is basically open and now you're trying to "cap" it and I think you're going to need the counter timbers and transom geometries to do this or perhaps a combination of both ideas.
-
Well you could try Model Expo's Sultana. It's the same scale as your Scotland (if you have the ME's version that is ) and it's a solid hull, so there's no need to worry about bulk heads and hull planking. It will require some sanding & shaping of the hull using templates and then adding the deck fittings and rigging. It's about 1/2 the cost of your Scotland. Sometimes ME runs this kit on sale and you can get for a lot less. You could also check out BlueJacket Shipcrafters "Skiff" kit. It's about as basic as you can get and under $40. I know what your going through, my first build was Constructo's Enterprise kit. Having a background building model cars and airplanes the Enterprise was just daunting. It took perseverance, patience, a lot of reading and help from forum members. When I look back at my Enterprise, I see so many things I should have done and now can do better. I'm really proud of that ship and every night I look at it and realize how far I have come. The ship you have is intimidating for a first timer but if you take your time, do some reading and ask for help, I think you could do it. Each ship that is built is unique and has it's own character that you build into it. Don't worry about being perfect the first time.
-
Your skill level is amazing, I asked about the officer because I have been looking for 2d officer for some Sketchup work I was doing.
-
Amazing work Magnus. When I watch the character walk from the front or rear and I pay attention to his feet the camera (floor) seems to be moving left and right. When I watch from the side at his feet it looks like he is walking on a tread mill. The only other observation I would make are the hands, he looks like he is ready to draw a gun. You may have mentioned this before but where did you get the measurements for the uniform? Are you just using photos and existing paintings?
-
If you're only looking to turn spars, mast, etc, I would check out the Grizzly Hobby Lathe. http://www.grizzly.com/products/Hobby-Lathe-Disc-Sander/H2669 I have one and it's come in handy for turning mast and spars and other small turning projects. It's easy to setup and use all need is the drill motor that fits the collar. You can attach it to your work bench with some clamps or mount it directly. I used it to turn the mast for my Enterprise.
-
Just plain help!
Don9of11 replied to torpedochief's topic in CAD and 3D Modelling/Drafting Plans with Software
You could try SketchUp, it's free and not to difficult to learn. -
Alan, I'm curious about a note in the upper left corner of the contract next to the first paragraph on page one and a note similar to this with the date of 1805 in the left-hand column several pages later next to the paragraphs Time of Launching. This is just speculation on my part but I wonder if the Bellerophon underwent a refit after the Battle of Trafalgar and these penned scantlings are from that period?
-
If you look closely next to the scantlings that have been changed or in some cases above the scantling, you will find there are initials. This means that the changes were agreed to, whether before or after the ship was built or if this was a common practice to mark the contract up in this manner, I can't determine.
-
Alan, why don't you start a separate configuration using the penned in dimensions, I've done that with the 74 I am working on. I put Steel's dimensions in a configuration all it's own within the same model that way I can refer to it when ever I want. Starting over has it's benefits too as it will test what you learned so far.
-
I tried Blender a few years back and I found it difficult to use. Blender like 3DS Max is an artistic program verses a mechanical drafting program (IMHO) I have seen a lot of cool stuff created with Blender and like any program you have to stick with it in order to learn it.
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.