David W
Members-
Posts
75 -
Joined
-
Last visited
About David W
- Birthday June 24
Profile Information
-
Location
Near Saratoga Springs, NY
-
Interests
Besides building an occasional model or two, street rods, RVing and teaching worms how to swim
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
Ken, your Fifie is really looking nice I'm envious of your progress in only 14 months - which is about what I have on mine. Setting up for an R/C system took way longer then expected with a better/larger prop shaft, motor, ESC, receiver and battery mounts. I have made up most of the individual deck items plus made a larger rudder. I'm currently fixing a messed up area on the first planking layer. Oh and your next 'challenge' will be the @#$% supplied fishing dory which will probably only take 20 hours or so! Looking forward to your next update
-
Ken_2 reacted to a post in a topic: Fifie by Ken_2 – Amati/Victory Models – 1:32 - Scottish Motor Fishing Vessel
-
Ken - you are doing a great job on this model!! Those fish hatches are a real pain with that post and ring assembly. I think it took me over an hour to assemble the first one for the wheel house door then decided that it was way out of scale and just used the post but then the door on my model has been modified to slide and open - which was a fun as well as pretty easy endeavor since I already made the roof a bit larger. Still not sure that the hatch rings are 'right' yet as they too seem to be too heavy. Looks like those blocks need to be redrilled with a bit larger hole when I get to that point. Makes me snicker when the front page of the Amati IB says that it should take 100-150 hours to build. HA!
-
David W reacted to a post in a topic: Fifie by Ken_2 – Amati/Victory Models – 1:32 - Scottish Motor Fishing Vessel
-
mtaylor reacted to a post in a topic: Planking, using CA glue, my Amati Fifie
-
All good information! Thanks folks I suspect that medium will be my choice and put Starbond on my Amazon wish list if for no other reason then that I have some of their activator. I considered the thick but the set time can be too long for the way this boat's hull is configured and the thin is too fast for my level of experience planking.
-
David W reacted to a post in a topic: Planking, using CA glue, my Amati Fifie
-
David W reacted to a post in a topic: Planking, using CA glue, my Amati Fifie
-
David W started following Caulk for RC hull?? RADIO , Planking, using CA glue, my Amati Fifie , Glue for second planking and 1 other
-
Someday soon I'll start the second planking my Fifie build. I'll be using CA glue. Of course I would like to use PVA but that's not the best way with this convoluted hull ship.that is danged hard to clamp planking other then with nails which on the second layer is not a good thing I've seen suggestions here and elsewhere that should use use extra thick, or maybe medium, or then thin or extra thin. Any comments as I really want a CA to set up pretty quickly. Thanks
-
David W reacted to a post in a topic: Fifie by Ken_2 – Amati/Victory Models – 1:32 - Scottish Motor Fishing Vessel
-
Canute reacted to a post in a topic: Mini Bench Drill Press
-
mtaylor reacted to a post in a topic: Mini Bench Drill Press
-
thibaultron reacted to a post in a topic: Mini Bench Drill Press
-
Interesting tool and probably a bunch more suitable then my floor mounted 16 speed, 3/4Hp drill press for model building. My only concern with one of these is that power pack and how it will survive long term vs a 120VAC unit with a rheostat for speed
-
David W reacted to a post in a topic: Fifie by carlo_i - Scale 1:32 - Scottish Herring Drifter - RADIO
-
A display case means that you will cutting dimensional lumber to size. For that a good 10" portable contractor saw like a DeWalt or Ryobi would be best using a good fence and sliding miter gauge plus many of these are pretty light weight. I have heavy duty cast iron table JET JTS-10 with a Delta fence and INCRA miter gauge. This saw weighs in at a lot of pounds but with that said, when 'tuned' it will shave pieces down to .010 but is overkill if you aren't doing a lot of work and moving often. Something like a Byrnes or Proxxon are great hobby saw but not big or powerful enough to size dimensional materials.
-
David W reacted to a post in a topic: Fifie by Ken_2 – Amati/Victory Models – 1:32 - Scottish Motor Fishing Vessel
-
Looking even better then the last post!!! I just blew the summer's dust and cobwebs off my Fifie on Monday and decided that I needed a plank bender since the first planking layer is using spliced full length lengths of wood strips and will need some edge bending which the hair curler I had been using just isn't hot enough.
-
David W reacted to a post in a topic: USCG Fast Response Cutter by drobinson02199 - FINISHED - Dumas - Scale 1:48
-
The boat is really starting to look great👍 "I have run out of 1mm x 1mm walnut planks used to simulate caulking." Instead of using the 1x1mm wood, you could use a fairly heavy black or brown thread Those skylights and hatch covers can be a royal pain where you sit, especially if you have too many thumbs on each hand. If you haven't started on the pilot house, you have another 'treat' coming. While you are further along then my Fifie endeavor, I've jumped ahead while glue was drying and have put the pilot house together. I extended the roof by 1/16" - 3/32" each side since it just didn't look right as Amati supplied it and looking at photos of real boats of the same design
-
David W reacted to a post in a topic: Fifie by Ken_2 – Amati/Victory Models – 1:32 - Scottish Motor Fishing Vessel
-
David W reacted to a post in a topic: USCG Fast Response Cutter by drobinson02199 - FINISHED - Dumas - Scale 1:48
-
David W reacted to a post in a topic: USCG Fast Response Cutter by drobinson02199 - FINISHED - Dumas - Scale 1:48
-
As a note to drobinson and others, 3m make several widths of fine line masking tapes that can be found at most auto body and parts stores - and it might be fresher then what AMAZON might supply. My history is one time with AMAZON for automotive masking tapes - and it wasn't good.
- 46 replies
-
- Fast Response Cutter
- Dumas
-
(and 2 more)
Tagged with:
-
Glue for second planking
David W replied to Ian K B's topic in Building, Framing, Planking and plating a ships hull and deck
Do you actually need filler? Or are there major low spots. Or are you just trying to fill between individual Planks. If filling between individual planks, consider that it's really out of sight and has no bearing on the completed model. If you have significant low spots, consider filling with a softer wood glued in place then sanded to shape instead of a soft filler that any kind of cement wont adhere to well. -
Looks to me that you are doing a fantastic job with a less then great model kit. I have a Dumas kit that I drag out occasionally and putter with - bought it in 1986 and it may never get done! Fully half of my model is replacement materials for that which didn't fit, wood that split or was missing from the sealed box.
- 46 replies
-
- Fast Response Cutter
- Dumas
-
(and 2 more)
Tagged with:
-
Caulk for RC hull?? RADIO
David W replied to Ian_Grant's topic in Painting, finishing and weathering products and techniques
Ian, there is another finishing (sanding) resin that's often sold in hobby shops that I've also considered and since I was late on my way to the dentist as I wrote the last, just plain forgot. Take a look at this as well. It has been out of stock recently but looks like AMAZON US at least, has it again: https://www.amazon.com/Pacer-Technology-Zap-Finishing-Adhesives/dp/B0006O8ESK?th=1 -
Caulk for RC hull?? RADIO
David W replied to Ian_Grant's topic in Painting, finishing and weathering products and techniques
I can fully understand not wanting to fiberglass a model but maybe just a coat or two of FINISHING resin, polyester comes to mind. I'm (slowly) building an Amati Fifie for R/C useand in the same dilemma 'glass or just a couple coats of resin then paint. I've' already sealed the inside with spar varnish plus paint but not fully comfortable with the outer skin/planking only spar varnished. This or similar is what I'm looking at using:https://www.amazon.com/dp/B00PZ1CU1G/?coliid=I1GHA86B7RTVXO&colid=2GHV6Y2C7OD8R&psc=1&ref_=lv_ov_lig_dp_it -
Still little (no) response to the question. Maybe because it's tradition that 'everyone' fills the gaps. Not really a big deal, just seems like a way to spend more time and materials for little or no return. As far as depression filling. yes, that needs to be corrected. POB models with too few bulkheads seem to have an endemic problem with too much distance between them, allowing planks to sag. Filler blocks between them first then a filler wood on top then sanded or otherwise fitted to proper dimensions/shape will work. I like balsa since it will form easily without distorting the planking but soft pine will also work if careful.
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.