Pride of Baltimore II by Richvee - Model Shipways - 1:64

[EricWilliamMarshall]

How's the build going?

[Richvee]

On 6/16/2022 at 12:41 PM, EricWilliamMarshall said:

How's the build going?

It sure had been a while. I still

need to finish planking the other side. It’s been a busy baseball season and that combined with work and house upkeep has kept me out

of the shipyard. I’ll get back at it soon. 

Edited June 19, 2022 by Richvee

[EricWilliamMarshall]

No worries - this is a hobby not a job! Thanks for the update!

[Richvee]

 Wow. Two years into this build already. It's been sitting quite a while. I've gotten back into the shipyard a bit, and the planking continues. Nothing worth showing, as it's coming along the same as the first side. 🙂. Recently  I've  been looking over the plans a bit getting ready for the deck planking, stern and bulwarks. Hopefully there's more progress soon. 

[Richvee]

Well, I've finally managed to finish planking the hull. I think it's OK. Learned a lot along the way, including the fact that cutting, fitting,  and installing planks is not my favorite part of this hobby.  I have to finish up the counter, and then on to filling some low spots and sanding. Maybe in another year or so I'll have that done 😁

 

 

[Richvee]

While planking the counter, and filling and sanding, I’m contemplating the next steps . Looks like there’s several directions I can take and see several  different methods to accomplish these things. 
   Once the hull is fully sanded and I’ve added some polyurethane, I think I’m going to add the inboard transom  pieces, paint the inboard planksheer and pre paint and install the combings prior to laying the deck. Looking past there, I like the idea of building and painting the bulwarks off the model and then install. Seems that’s the best way to get sharp, clean paint on inside of the bulwarks being that the planksheer, stanchions and rails are different colors.  . I’ve got time to figure that out. Sanding, filling, coating, transom, combings, and finally deck planking all before the upper bulwarks. That may take me into 2024 and beyond 😂

Edited February 12, 2023 by Richvee

[Richvee]

The hull has been sanded, I've added the counter planking and the lower half of the transom, and the stern knees. Not sure if adding the stern knees at this point was a good idea, as I've already broke a small piece off one. I'll deal with that when I plank the upper half of the transom. That's not going to be until I have the bulwarks in place because looks like that whole Counter/transom, transom trim, rail, bulwarks is going to take a lot of tinkering to line up and look at least halfway decent. I figured I should get the stern knees in so I can add the planksheer in between them, get them painted before I start planking the deck. 

 I've started a few coats of inboard planksheer paint, and measured out the areas for the deck coamings. That will be the next step. Building, paintig, and adding the coamings and stern planksheer. Then it will be on to planking the deck. 

 

The sanded hull

The counter and stern knees

 

And the layout of the coamings for the deck fixtures with painted and masked planksheer

 

 

 

[EricWilliamMarshall]

She is looking good! 

[Richvee]

Thanks Eric. I’ve actually just finished the coamings and I have a few coats of paint on them. They’ll be on the deck soon, and the deck planking will begin. I’ll add a few pics when the coamings are installed. 

[Richvee]

Thanks for the likes, all.

 Some progress. 

I've cut, sanded, painted, and installed the coamings. I'm sure the paint will need touching up before all is said and done, but this seemed to the best way for me to get a nice clean line of red coaming against the deck. Installing the coamings first also seemed to be the best way for me to get the coamings to look flush to the deck given the deck's curvature, I guess we'll see if how it works out as the deck planking procedes. 

 

I have started by installing the nibbing planks to the bulkheads and edged glued to the planksheer. This will be my first attempt at Nibbing plaks so I'm hoping to get the hang of it quickly and not butcher this task. But first, the two wider thicker planks down the center. These are simply one on each side of the centerline, straight down the ship. Can't forget to cut out the decking for the mast holes. 

 

 

Looks like I need to manipulate the fore side of the large cabin coaming. I'll unglue, and add some some wood shims on the port side. That should even out the coaming height side to side. 

[Richvee]

Planking continues at a snail's pace, and my first attempts at nibbing are complete. You can practice, but once you start making cuts into that planksheer, there's really no turning back. So far so good...No major issues. Far from perfect, but I can live with it. 

[Richvee]

Deck planking had been moving at a decent pace. I’ve been sanding a little with 220 grit as I go. Nibbing isn’t as difficult as I thought it would be. I think it’s coming out pretty good. I switched from CA to a wood glue for the deck planking. Gives me a lot more control, and easier to pull up some planks where I wasn’t  happy with how they originally looked. A few more planks to finish off, then sanding, and touching up the red combings and planksheer. I also need to cut in the wider boards that sit under the fife rails and windlass. 

Starboard side completed

 

Soon I’ll need to start considering stain color for the deck. 
Question—— Do I apply a poly coat on the deck  prior to staining? Or stain first, then poly coat?  

[yvesvidal]

Stain first. Wipe on Poly will create a plastic film on top of the wood.

It may work both ways, but I would stain first.

Best, is to try on scrap woods.

 

Yves

[Richvee]

Deck planking completed.  Next I’ll cut in the wide support planks for the fife rail and windlass. Then sanding and staining. 

 

[BobG]

Nice work, Rich!

[yvesvidal]

I was in Annapolis this weekend attending the Sailboat show. The Pride of Baltimore 2 was there, docked and available for the public to tour. 

What a beautiful sight! That ship is quite impressive and the most interesting part is how slanted the masts are. I have never seen something like that on a period ship or even on a more recent vessel. The deck had all the guns in place plus (unfortunately) all the modern safety stuff that are now required, to navigate.

 

Yves

Edited October 14, 2023 by yvesvidal

[Richvee]

Ten months later, Finally some progress. I didn't realize I never added photos of the stained and poly coated deck. 

I have also completed the upper bulwark sections. I assembled them off the model. I will paint them and then instal them after adding some inboard details like cleats, rings, etc. The stringers are continuous pieces over the gunport openings, so I'll add them once the bulwarks are installed. Here's a few shots of the bulwarks. Nothing installed ..Just placed for a quick picture or two. Inboard details and paint next up. 

 

Hopefully it will be less than ten months before the next update! 

[Richvee]

With baseball season over there's some more time to modeling again. Next up was adding cleats, eyebolts, calvils and mooring ports to the bulwarks. Painting and installing.

 

Now that the bulwarks were in place, I added the stringers along the inside and outside that will sit under the top rail. I figured this would give me more area for the top rail to adhere to.  

 

 Outboard stringer

 

Once they were installed, I sanded the top to make the stringers and stanchions level to accommodate the top rail. 

 

Outboard stringer  is painted. looks like I may have made those scuppers a bit large. 😔

 

 

Haven't painted the inboard stringer yet, but that will be done before the top rail is installed. 

I started making sections of the top rail. Cutting the right curve to follow the bulwark, a smooth edge, and a uniform width is proving to be quite challenging. I've been cutting the curve of the rail by taping a 1/2" wide, 3/64" thick strip to the workbench. flipping the hull upside down, and tracing along the outboard stringer with a sharp pencil, then cutting that curve about 1/16" past there, giving me the 1/32 overhang and an extra 1/32 to sand the side to round. Then with a divider, measure 7/32" in and scribe a line and cut the inside of the rail, that leaves me the extra 1.32" to smooth and round off the rail. I think I'll stain these pieces before installing. They are to be stained a mahogany color, and pictures of the real ship show they are varnished with a gloss. 

 

Here's the start of the rails

 

And placed to test curve and width. So far, so good..Only took about 5 tries to get these three decent pieces done! You'll notice inboard stringer missing at the top of last picture..That's to accommodate the pin rails, which will adhere to the bulwark and the underside of the top rail.