Force9

Guys -
 
Thank you all for following along.  I should have some updates soon with my progress on dead eyes, cleats, and ring bolts.
 
Robin - thank you for wading thru my build log... I wish you'd reconsider doing some paintings from this era.  I still think no recent artist has done the Constitution/Guerriere battle correctly.
 
Stay tuned!
 
Thx
Evan

It's taken me a bit, but I've now finished the yards and rigging of the fore mast. Aging eyes and hands, combined with small scale, have made this a slow and difficult task.
 
After my last update, in which I had finished the lower yard and started the topsail yard, I completed that yard and mounted them both on the pins in the mast. The only item of note on the topsail yard is the parrel, which I made up from pear strip, shaped and drilled, and small beads.
 
The rigging then proceeded through the jeers, slings, trusses, parrel, lifts, clews, sheets, tyes, halliards and braces, and ended with the lower clew garnets, sheets and tacks. The lines were tied off to various timber heads, pins, rails and bitts and rope coils were added.
 
Now I get to repeat this process on the main and mizzen.
 
Bob

Cheers Keith, just what I am doing.
 
But still manage to take a peek at this build and do some small things to it.

Marked out the lines for the planking after removing most detail to make again later.

But since then Had some more info on what the spacing for planking and layout should be.



Thanks to Daniel for helping before I started laying the planks.
But did manage to lay a couple of carpets.


More soon me thinks.

Frank

Guys -
 
Thank you all for following along.  I should have some updates soon with my progress on dead eyes, cleats, and ring bolts.
 
Robin - thank you for wading thru my build log... I wish you'd reconsider doing some paintings from this era.  I still think no recent artist has done the Constitution/Guerriere battle correctly.
 
Stay tuned!
 
Thx
Evan

So... A couple of comedians!    Don't people remember that she was called "Old Ironsides"???!! - She never absorbed any damage!  Everything bounced off!!!  Well, at least it all bounced off for my model.
 
 
Here is the latest...
 
It is amazing how many holes need to be drilled into a sailing ship model!  I've been busy with the mini spiral drill and #76 bit for the past few weekends.
 
It is also amazing to uncover the various nuances that go into these builds.  I've been drilling the many small holes for the Jotika eyelets that will be installed around the interior of the gun ports.  
 
Most references indicate the breeching terminating on a ring bolt positioned near the trucks in line with the bottom of the gun port.  The outhaul tackle, however, is often shown leading at an angle to an eyelet positioned about midway between the two guns.  It would seem to me to be more efficient if this tackle ran more parallel to the gun barrel - no waste in lateral effort when hauling on the tackle.  That would seem to be the arrangement on most of the contemporary ship models... An eyebolt for the outhaul tackle positioned about midway up on the gun port and near the opening.  The ring bolt for the breeching rope positioned directly below in line with the bottom of the port.
 
We can also see this type of set up on the remarkable War of 1812 wrecks of the Hamilton and Scourge that lie preserved at the bottom of Lake Ontario. Both were swamped by a sudden squall and lost at the same time.  (Actually the wrecks were once remarkably well preserved but have now become encrusted with an invasive species of mussel):
 

The boarding cutlasses are very cool.
 
Here is the approach I took:

 
None of these eyelets are glued in... Just a sample of positioning.  I'll blacken them and glue the upper eyelets, but I'll attach the lower ring bolts to the breeching rope when I rig the cannon off the ship before attaching these to the bulwarks.
 
Evan

Cheers Frank and Popeye!
 
Folks -
 
I've reached that point in the build where there is nothing more I can do to delay the inevitable... I have to start accounting for the rigging and making sure that I've incorporated the necessary end points into the half hulls before I start to glue it all together.  
 
I consulted the usual suspects:
 
1. The Revell rigging plans
2. The Bluejacket kit manual and rigging plans - Larry Arnot/Tyrone Martin
3. AOTS USS Constitution - Karl Heinz Marquardt
4. CONSTITUTION - All Sails Up and Flying - Olof Eriksen
5. The Charles Ware 1817 Sail plan (National Archives)
6. The "Hull" model in the Peabody Essex Museum (PEM) collection.
 
I've been poring over these different representations of the rigging layout of Old Ironsides for many months and have started to form some sort of plan.  For the most part I will follow the guidance of Olof Eriksen, but fall back on the Bluejacket plans in some cases.  Eriksen's work is focused on her 1815 configuration, so I'll try to insert some 1812 era modifications wherever appropriate - mostly using the Hull model for corrections.  Ultimately this is all going to involve a fair bit of guesswork and intuition tempered by the realities imposed by the Revell model itself. In some cases the molding of the hull will impose limitations that are more than I'm willing to modify - I'll just roll with what is there.
 
Here is my first compromise:
 

 

 
Some may recall that I eliminated the chesstree included in the kit and filled in the holes at the gun deck level that originally allowed for the Fore Sheet and Main Tack to enter and get tied off within... I just feel that by 1812 these lines would've been led to the spar deck to allow for better control and coordination.  Eriksen shows the Fore Sheet entering thru a sheave in the spar deck bulwark just forward of the last carronade before the break in the bulwark at the waist.  The Revell kit does not have much of a bulwark at that point.  I couldn't widen it because the "entry port" is situated here with the cleats/steps leading up the side.  I was not willing to move that stuff over with all that scratch building... Marquardt offers a solution.  He shows a sheave added on the waist for the Fore Sheet to pass thru and tie off to a cleat mounted nearby on the deck.  Do I think this is historically accurate?  Nah... But it suits my purpose.
 
The first eyebolt near the sheave is the tie off for the Fore Sheet.  The eyebolt mounted forward on the waist near the fo'c's'le bulwark will eventually have a block mounted for the Main Tack to lead inboard. I still need to drill the hole just aft of the fore channel for the Main Tack tie off point.
 
Here is the sheave I cut into the spar deck bulwark for the Main Sheet:
 

 
I mounted a cleat on the inside to tie off the Main Sheet:

 
More to come shortly
 
Thanks for the interest
 
Evan

Guys -
 
Thank you all for following along.  I should have some updates soon with my progress on dead eyes, cleats, and ring bolts.
 
Robin - thank you for wading thru my build log... I wish you'd reconsider doing some paintings from this era.  I still think no recent artist has done the Constitution/Guerriere battle correctly.
 
Stay tuned!
 
Thx
Evan

Cheers Frank and Popeye!
 
Folks -
 
I've reached that point in the build where there is nothing more I can do to delay the inevitable... I have to start accounting for the rigging and making sure that I've incorporated the necessary end points into the half hulls before I start to glue it all together.  
 
I consulted the usual suspects:
 
1. The Revell rigging plans
2. The Bluejacket kit manual and rigging plans - Larry Arnot/Tyrone Martin
3. AOTS USS Constitution - Karl Heinz Marquardt
4. CONSTITUTION - All Sails Up and Flying - Olof Eriksen
5. The Charles Ware 1817 Sail plan (National Archives)
6. The "Hull" model in the Peabody Essex Museum (PEM) collection.
 
I've been poring over these different representations of the rigging layout of Old Ironsides for many months and have started to form some sort of plan.  For the most part I will follow the guidance of Olof Eriksen, but fall back on the Bluejacket plans in some cases.  Eriksen's work is focused on her 1815 configuration, so I'll try to insert some 1812 era modifications wherever appropriate - mostly using the Hull model for corrections.  Ultimately this is all going to involve a fair bit of guesswork and intuition tempered by the realities imposed by the Revell model itself. In some cases the molding of the hull will impose limitations that are more than I'm willing to modify - I'll just roll with what is there.
 
Here is my first compromise:
 

 

 
Some may recall that I eliminated the chesstree included in the kit and filled in the holes at the gun deck level that originally allowed for the Fore Sheet and Main Tack to enter and get tied off within... I just feel that by 1812 these lines would've been led to the spar deck to allow for better control and coordination.  Eriksen shows the Fore Sheet entering thru a sheave in the spar deck bulwark just forward of the last carronade before the break in the bulwark at the waist.  The Revell kit does not have much of a bulwark at that point.  I couldn't widen it because the "entry port" is situated here with the cleats/steps leading up the side.  I was not willing to move that stuff over with all that scratch building... Marquardt offers a solution.  He shows a sheave added on the waist for the Fore Sheet to pass thru and tie off to a cleat mounted nearby on the deck.  Do I think this is historically accurate?  Nah... But it suits my purpose.
 
The first eyebolt near the sheave is the tie off for the Fore Sheet.  The eyebolt mounted forward on the waist near the fo'c's'le bulwark will eventually have a block mounted for the Main Tack to lead inboard. I still need to drill the hole just aft of the fore channel for the Main Tack tie off point.
 
Here is the sheave I cut into the spar deck bulwark for the Main Sheet:
 

 
I mounted a cleat on the inside to tie off the Main Sheet:

 
More to come shortly
 
Thanks for the interest
 
Evan

Guys -
 
Thank you all for following along.  I should have some updates soon with my progress on dead eyes, cleats, and ring bolts.
 
Robin - thank you for wading thru my build log... I wish you'd reconsider doing some paintings from this era.  I still think no recent artist has done the Constitution/Guerriere battle correctly.
 
Stay tuned!
 
Thx
Evan

Let's proceed with the gun deck.
I've got to eliminate those darn seams.
I need to carefully align each deck piece to each adjacent neighbor. Unfortunately, the middle section of the decking is moulded a bit thicker than the others, so I need to build up the thickness on the end pieces to match before I can glue and clamp.  The stern section needed a little more help than the bow section:


After also adding a larger set of styrene strips to the underside to help align the surfaces (keeping away from the edges to not interfere with the mounting tabs moulded into the hull halves) I can go ahead and liberally smear everything with glue and clamp it all down:



Once everything had dried for 24 hours I came back and absolutely assaulted the surface with 80 grit sandpaper:
 
 


I think those seams are gone.  I'll next begin to prep the deck with some 150 grit sanding and start in on scribing the planks.
Thanks for following along
 

Back to the build...
 
Spent my last few sessions scratching away at the gun deck to put some semblance of planking in place.
 
I set up the workbench with a bit of old cardboard for the pins underneath the deck to grab onto (and not break off) while I abused the topside.  I clamped the deck down by the bow to hold her steady and proceeded to scribe the decking.
 
The process was relatively simple and I hope I illustrate it well enough.  I used some spare lengths of styrene strips to represent each row of planking to establish the alignment of my straight edge.  I used the existing hatch coamings as the baseline, laid a styrene strip against it, then aligned the straight edge to the strip.  After clamping the edge down, I would remove the temporary styrene and scribe the line.  I would add another temporary strip to the mix to align my edge to the next row of planking... and so on... working from the middle out to the edges.
 




 
For the middle decking I clamped down the straight edge and used the styrene strips for guidance (custom fit for the space)

 
Next I scribed in a four step butt pattern following the guidance of Longridge (pages 120-21).
 
Came back along with a 180 grit sanding block and smoothed down the edges.
 
Took about six hours altogether.

Here are some better photos with lighting that highlights the scribed lines...
 




 
The step pattern was initially laid out using the diagram in the Longridge book (Pg 121).  Then it was a matter of coming along and scribing every fifth plank - either vertically or horizontally until the deck was complete.
 
Thanks for looking

http://usscm.blogspot.com/2014/02/slip-shod-truth-about-early-navy-shoes.html

http://usscm.blogspot.com/2014/02/slip-shod-truth-about-early-navy-shoes.html

Cheers Frank and Popeye!
 
Folks -
 
I've reached that point in the build where there is nothing more I can do to delay the inevitable... I have to start accounting for the rigging and making sure that I've incorporated the necessary end points into the half hulls before I start to glue it all together.  
 
I consulted the usual suspects:
 
1. The Revell rigging plans
2. The Bluejacket kit manual and rigging plans - Larry Arnot/Tyrone Martin
3. AOTS USS Constitution - Karl Heinz Marquardt
4. CONSTITUTION - All Sails Up and Flying - Olof Eriksen
5. The Charles Ware 1817 Sail plan (National Archives)
6. The "Hull" model in the Peabody Essex Museum (PEM) collection.
 
I've been poring over these different representations of the rigging layout of Old Ironsides for many months and have started to form some sort of plan.  For the most part I will follow the guidance of Olof Eriksen, but fall back on the Bluejacket plans in some cases.  Eriksen's work is focused on her 1815 configuration, so I'll try to insert some 1812 era modifications wherever appropriate - mostly using the Hull model for corrections.  Ultimately this is all going to involve a fair bit of guesswork and intuition tempered by the realities imposed by the Revell model itself. In some cases the molding of the hull will impose limitations that are more than I'm willing to modify - I'll just roll with what is there.
 
Here is my first compromise:
 

 

 
Some may recall that I eliminated the chesstree included in the kit and filled in the holes at the gun deck level that originally allowed for the Fore Sheet and Main Tack to enter and get tied off within... I just feel that by 1812 these lines would've been led to the spar deck to allow for better control and coordination.  Eriksen shows the Fore Sheet entering thru a sheave in the spar deck bulwark just forward of the last carronade before the break in the bulwark at the waist.  The Revell kit does not have much of a bulwark at that point.  I couldn't widen it because the "entry port" is situated here with the cleats/steps leading up the side.  I was not willing to move that stuff over with all that scratch building... Marquardt offers a solution.  He shows a sheave added on the waist for the Fore Sheet to pass thru and tie off to a cleat mounted nearby on the deck.  Do I think this is historically accurate?  Nah... But it suits my purpose.
 
The first eyebolt near the sheave is the tie off for the Fore Sheet.  The eyebolt mounted forward on the waist near the fo'c's'le bulwark will eventually have a block mounted for the Main Tack to lead inboard. I still need to drill the hole just aft of the fore channel for the Main Tack tie off point.
 
Here is the sheave I cut into the spar deck bulwark for the Main Sheet:
 

 
I mounted a cleat on the inside to tie off the Main Sheet:

 
More to come shortly
 
Thanks for the interest
 
Evan

The Rudder...
 
The kit provided version was noticeably lacking any copper plating so, just for yucks, I thought I'd build my own version of the rudder...
 
It has always struck me as odd that the Revell Constitution has a cylindrical rudder head instead of a squared one similar to other period ships.  My first thought was to replace that... But then I did some research.  It turns out that the good folks at Revell probably got that right!  We do see the cylindrical rudder head on the Hull model:
 

 
When Constitution was first launched she had a typical "rule joint" type rudder with the square rudder head.  This rudder type required a larger opening in the lower transom to allow for the arc of the rudder head as it swung back and forth during turns.  Howard Chappelle notes in his American Sailing Navy book that the US Navy had replaced all of their  rudders with the newer "plug" type by 1801 or thereabouts.  This new innovation utilized the cylindrical shape and moved the rudder head forward so that the center aligned along the same axis as the pintles.  This eliminated the arc pattern of the rudder head - instead it spun exactly in line with the pivot point of the pintles.  This allowed for a much smaller opening under the transom - and perhaps a tighter feel for the helm.  Learn something every day.
 
Here was my approach:
 
I glued together four strips of .100 x .156" styrene (Evergreen 177) and did the basic shaping on a small vice using a heavy file.  Next I carved a groove into some appropriate rod styrene (same as what I used on the Galley Stove pipe) and affixed that to the top - centered, of course, over the leading edge.  Once done, I came back along and notched in the locations for the rudder pintles:


 
Now I needed to copper plate the thing. I used .010 x .125" (Evergreen 106) for the plates.  I whipped up a quick jig (using some available scraps) to help align the "copper" strips while I rolled in the rivet pattern on one edge.  I used the smallest roller in my collection to approximate the pattern existing on the kit plating.  The rest of the bolt heads I did by hand using my trusty scribe tool.

 
Took me about an hour to plate each side:

 
Lastly I came along and added the various straps, spectacle plate, etc.
 
Here is the result:



 
BTW - It turns out, the kit provided rudder is actually pretty good.  As noted it properly represents the "plug" type version.  This is not surprising since it is based on the Campbell plan and he consulted extensively with Chappelle. The rudder edges also taper nicely from forward edge to after edge, and from top to bottom.  Ultimately, a very nice upgrade could probably be had by simply adding the copper plates.
 

 
Thanks again folks for wading thru my entries!
EG

I was going to wait until I had the brake pumps completed, but here are some quick snaps of the current state of things:
 
I've got the bitts completed (except for some rings for the stoppers that'll wait until after the initial painting):


 
Also have completed the cisterns and covers for the chain pumps - still need to fashion some handles:

 
Just for a bit of extra fun... I've left off the cover on one of the cisterns to "expose" the underlying chain wheel:


 

 
It started with me strolling through the model train store for something to use for my capstan drumheads.  I didn't find anything suitable, but this little packet did catch my eye:
 

 
And I thought, hmmmm...
 
So after forking over too much hard earned cash (I think each wheel ended up being over a buck!) I trimmed them up slightly and glued on some small lengths of styrene rod then snipped off the ends.  I suppose some spare PE railings or scale ladder bent around the circumference would've worked as well:
 

 

 
They are really cable sheaves and aren't quite perfect for the job, but at this scale, and barely visible thru the openings, it should suffice well enough.  I'm just gonna paint it black then leave well enough alone - I don't fancy trying to replicate the chain.  That'd be too fiddly and would likely diminish the effect.
 
And just to make sure people know these things don't all work out on the first try... Here is my debris field:

 
Thanks for following along

Cheers Frank and Popeye!
 
Folks -
 
I've reached that point in the build where there is nothing more I can do to delay the inevitable... I have to start accounting for the rigging and making sure that I've incorporated the necessary end points into the half hulls before I start to glue it all together.  
 
I consulted the usual suspects:
 
1. The Revell rigging plans
2. The Bluejacket kit manual and rigging plans - Larry Arnot/Tyrone Martin
3. AOTS USS Constitution - Karl Heinz Marquardt
4. CONSTITUTION - All Sails Up and Flying - Olof Eriksen
5. The Charles Ware 1817 Sail plan (National Archives)
6. The "Hull" model in the Peabody Essex Museum (PEM) collection.
 
I've been poring over these different representations of the rigging layout of Old Ironsides for many months and have started to form some sort of plan.  For the most part I will follow the guidance of Olof Eriksen, but fall back on the Bluejacket plans in some cases.  Eriksen's work is focused on her 1815 configuration, so I'll try to insert some 1812 era modifications wherever appropriate - mostly using the Hull model for corrections.  Ultimately this is all going to involve a fair bit of guesswork and intuition tempered by the realities imposed by the Revell model itself. In some cases the molding of the hull will impose limitations that are more than I'm willing to modify - I'll just roll with what is there.
 
Here is my first compromise:
 

 

 
Some may recall that I eliminated the chesstree included in the kit and filled in the holes at the gun deck level that originally allowed for the Fore Sheet and Main Tack to enter and get tied off within... I just feel that by 1812 these lines would've been led to the spar deck to allow for better control and coordination.  Eriksen shows the Fore Sheet entering thru a sheave in the spar deck bulwark just forward of the last carronade before the break in the bulwark at the waist.  The Revell kit does not have much of a bulwark at that point.  I couldn't widen it because the "entry port" is situated here with the cleats/steps leading up the side.  I was not willing to move that stuff over with all that scratch building... Marquardt offers a solution.  He shows a sheave added on the waist for the Fore Sheet to pass thru and tie off to a cleat mounted nearby on the deck.  Do I think this is historically accurate?  Nah... But it suits my purpose.
 
The first eyebolt near the sheave is the tie off for the Fore Sheet.  The eyebolt mounted forward on the waist near the fo'c's'le bulwark will eventually have a block mounted for the Main Tack to lead inboard. I still need to drill the hole just aft of the fore channel for the Main Tack tie off point.
 
Here is the sheave I cut into the spar deck bulwark for the Main Sheet:
 

 
I mounted a cleat on the inside to tie off the Main Sheet:

 
More to come shortly
 
Thanks for the interest
 
Evan

Cheers Frank and Popeye!
 
Folks -
 
I've reached that point in the build where there is nothing more I can do to delay the inevitable... I have to start accounting for the rigging and making sure that I've incorporated the necessary end points into the half hulls before I start to glue it all together.  
 
I consulted the usual suspects:
 
1. The Revell rigging plans
2. The Bluejacket kit manual and rigging plans - Larry Arnot/Tyrone Martin
3. AOTS USS Constitution - Karl Heinz Marquardt
4. CONSTITUTION - All Sails Up and Flying - Olof Eriksen
5. The Charles Ware 1817 Sail plan (National Archives)
6. The "Hull" model in the Peabody Essex Museum (PEM) collection.
 
I've been poring over these different representations of the rigging layout of Old Ironsides for many months and have started to form some sort of plan.  For the most part I will follow the guidance of Olof Eriksen, but fall back on the Bluejacket plans in some cases.  Eriksen's work is focused on her 1815 configuration, so I'll try to insert some 1812 era modifications wherever appropriate - mostly using the Hull model for corrections.  Ultimately this is all going to involve a fair bit of guesswork and intuition tempered by the realities imposed by the Revell model itself. In some cases the molding of the hull will impose limitations that are more than I'm willing to modify - I'll just roll with what is there.
 
Here is my first compromise:
 

 

 
Some may recall that I eliminated the chesstree included in the kit and filled in the holes at the gun deck level that originally allowed for the Fore Sheet and Main Tack to enter and get tied off within... I just feel that by 1812 these lines would've been led to the spar deck to allow for better control and coordination.  Eriksen shows the Fore Sheet entering thru a sheave in the spar deck bulwark just forward of the last carronade before the break in the bulwark at the waist.  The Revell kit does not have much of a bulwark at that point.  I couldn't widen it because the "entry port" is situated here with the cleats/steps leading up the side.  I was not willing to move that stuff over with all that scratch building... Marquardt offers a solution.  He shows a sheave added on the waist for the Fore Sheet to pass thru and tie off to a cleat mounted nearby on the deck.  Do I think this is historically accurate?  Nah... But it suits my purpose.
 
The first eyebolt near the sheave is the tie off for the Fore Sheet.  The eyebolt mounted forward on the waist near the fo'c's'le bulwark will eventually have a block mounted for the Main Tack to lead inboard. I still need to drill the hole just aft of the fore channel for the Main Tack tie off point.
 
Here is the sheave I cut into the spar deck bulwark for the Main Sheet:
 

 
I mounted a cleat on the inside to tie off the Main Sheet:

 
More to come shortly
 
Thanks for the interest
 
Evan

So... A couple of comedians!    Don't people remember that she was called "Old Ironsides"???!! - She never absorbed any damage!  Everything bounced off!!!  Well, at least it all bounced off for my model.
 
 
Here is the latest...
 
It is amazing how many holes need to be drilled into a sailing ship model!  I've been busy with the mini spiral drill and #76 bit for the past few weekends.
 
It is also amazing to uncover the various nuances that go into these builds.  I've been drilling the many small holes for the Jotika eyelets that will be installed around the interior of the gun ports.  
 
Most references indicate the breeching terminating on a ring bolt positioned near the trucks in line with the bottom of the gun port.  The outhaul tackle, however, is often shown leading at an angle to an eyelet positioned about midway between the two guns.  It would seem to me to be more efficient if this tackle ran more parallel to the gun barrel - no waste in lateral effort when hauling on the tackle.  That would seem to be the arrangement on most of the contemporary ship models... An eyebolt for the outhaul tackle positioned about midway up on the gun port and near the opening.  The ring bolt for the breeching rope positioned directly below in line with the bottom of the port.
 
We can also see this type of set up on the remarkable War of 1812 wrecks of the Hamilton and Scourge that lie preserved at the bottom of Lake Ontario. Both were swamped by a sudden squall and lost at the same time.  (Actually the wrecks were once remarkably well preserved but have now become encrusted with an invasive species of mussel):
 

The boarding cutlasses are very cool.
 
Here is the approach I took:

 
None of these eyelets are glued in... Just a sample of positioning.  I'll blacken them and glue the upper eyelets, but I'll attach the lower ring bolts to the breeching rope when I rig the cannon off the ship before attaching these to the bulwarks.
 
Evan

So... A couple of comedians!    Don't people remember that she was called "Old Ironsides"???!! - She never absorbed any damage!  Everything bounced off!!!  Well, at least it all bounced off for my model.
 
 
Here is the latest...
 
It is amazing how many holes need to be drilled into a sailing ship model!  I've been busy with the mini spiral drill and #76 bit for the past few weekends.
 
It is also amazing to uncover the various nuances that go into these builds.  I've been drilling the many small holes for the Jotika eyelets that will be installed around the interior of the gun ports.  
 
Most references indicate the breeching terminating on a ring bolt positioned near the trucks in line with the bottom of the gun port.  The outhaul tackle, however, is often shown leading at an angle to an eyelet positioned about midway between the two guns.  It would seem to me to be more efficient if this tackle ran more parallel to the gun barrel - no waste in lateral effort when hauling on the tackle.  That would seem to be the arrangement on most of the contemporary ship models... An eyebolt for the outhaul tackle positioned about midway up on the gun port and near the opening.  The ring bolt for the breeching rope positioned directly below in line with the bottom of the port.
 
We can also see this type of set up on the remarkable War of 1812 wrecks of the Hamilton and Scourge that lie preserved at the bottom of Lake Ontario. Both were swamped by a sudden squall and lost at the same time.  (Actually the wrecks were once remarkably well preserved but have now become encrusted with an invasive species of mussel):
 

The boarding cutlasses are very cool.
 
Here is the approach I took:

 
None of these eyelets are glued in... Just a sample of positioning.  I'll blacken them and glue the upper eyelets, but I'll attach the lower ring bolts to the breeching rope when I rig the cannon off the ship before attaching these to the bulwarks.
 
Evan

Let's proceed with the gun deck.
I've got to eliminate those darn seams.
I need to carefully align each deck piece to each adjacent neighbor. Unfortunately, the middle section of the decking is moulded a bit thicker than the others, so I need to build up the thickness on the end pieces to match before I can glue and clamp.  The stern section needed a little more help than the bow section:


After also adding a larger set of styrene strips to the underside to help align the surfaces (keeping away from the edges to not interfere with the mounting tabs moulded into the hull halves) I can go ahead and liberally smear everything with glue and clamp it all down:



Once everything had dried for 24 hours I came back and absolutely assaulted the surface with 80 grit sandpaper:
 
 


I think those seams are gone.  I'll next begin to prep the deck with some 150 grit sanding and start in on scribing the planks.
Thanks for following along
 

Folks...
 
My wife originally hails from Boston so we make a few trips back periodically to visit with family and friends. This year they were really making a big deal out of the July 4 celebration with Old Ironsides as the centerpiece of the commemoration of the Bicentennial of the War of 1812 - so we decided to make our trip coincide with the festivities.
 
On Tuesday mornings during peak season the USS Constitution offers a special behind the scenes "Constitution Experience" tour of the great ship for a limited sized group (you need to pre-register thru the website). You get to see the morning flag raising and morning gun before heading aboard. The tour includes the captains quarters, the orlop deck, and a chance to crawl down into the after powder room - all spaces normally off limits to us civilians.
 

 



During Cdr Tyrone Martin's tenure he had the forward gun modified to fire salutes. Here is the exposed loading tray of the surplus WWII anti-aircraft gun utilized for the purpose (each firing pin now costs $60 because of scarcity):

The Tiller:


Here is the scuttle down to the after powder room:


Here is some original timber (transom wings?) in the aftermost space of the magazine:

Here is my foot standing on original wood. The guide says it is the keel - but it is more likely the keelson or deadwood on top:

Orlop deck with the diagonal riders:

 
USS Constitution is, of course, still a commissioned warship in the US Navy so the guides are all active duty sailors and marines. The facts as presented in the tour are a bit sketchy in terms of accuracy, but the intent is well-meaning. Here are a few of the most egregious:
- "The frames are spaced two - four inches apart unlike the British ships, which were three or four FEET apart."
- "The crew fired a round every 90 seconds. The British crew fired every two to three minutes." (The opposite was probably true)
- "The ship could only fire every other gun in a broadside - otherwise a full broadside fired from every gun would tip the ship over."
 
Overall it was a terrific morning clambering around inside the great ship.

Cheers Frank and Popeye!
 
Folks -
 
I've reached that point in the build where there is nothing more I can do to delay the inevitable... I have to start accounting for the rigging and making sure that I've incorporated the necessary end points into the half hulls before I start to glue it all together.  
 
I consulted the usual suspects:
 
1. The Revell rigging plans
2. The Bluejacket kit manual and rigging plans - Larry Arnot/Tyrone Martin
3. AOTS USS Constitution - Karl Heinz Marquardt
4. CONSTITUTION - All Sails Up and Flying - Olof Eriksen
5. The Charles Ware 1817 Sail plan (National Archives)
6. The "Hull" model in the Peabody Essex Museum (PEM) collection.
 
I've been poring over these different representations of the rigging layout of Old Ironsides for many months and have started to form some sort of plan.  For the most part I will follow the guidance of Olof Eriksen, but fall back on the Bluejacket plans in some cases.  Eriksen's work is focused on her 1815 configuration, so I'll try to insert some 1812 era modifications wherever appropriate - mostly using the Hull model for corrections.  Ultimately this is all going to involve a fair bit of guesswork and intuition tempered by the realities imposed by the Revell model itself. In some cases the molding of the hull will impose limitations that are more than I'm willing to modify - I'll just roll with what is there.
 
Here is my first compromise:
 

 

 
Some may recall that I eliminated the chesstree included in the kit and filled in the holes at the gun deck level that originally allowed for the Fore Sheet and Main Tack to enter and get tied off within... I just feel that by 1812 these lines would've been led to the spar deck to allow for better control and coordination.  Eriksen shows the Fore Sheet entering thru a sheave in the spar deck bulwark just forward of the last carronade before the break in the bulwark at the waist.  The Revell kit does not have much of a bulwark at that point.  I couldn't widen it because the "entry port" is situated here with the cleats/steps leading up the side.  I was not willing to move that stuff over with all that scratch building... Marquardt offers a solution.  He shows a sheave added on the waist for the Fore Sheet to pass thru and tie off to a cleat mounted nearby on the deck.  Do I think this is historically accurate?  Nah... But it suits my purpose.
 
The first eyebolt near the sheave is the tie off for the Fore Sheet.  The eyebolt mounted forward on the waist near the fo'c's'le bulwark will eventually have a block mounted for the Main Tack to lead inboard. I still need to drill the hole just aft of the fore channel for the Main Tack tie off point.
 
Here is the sheave I cut into the spar deck bulwark for the Main Sheet:
 

 
I mounted a cleat on the inside to tie off the Main Sheet:

 
More to come shortly
 
Thanks for the interest
 
Evan

Work on the Funnel and its platforms continues.