donrobinson

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

Hhahahahahaha Mike, You got me laughing on that one. I may need to have a cocktail(drink) to calm down. Good news about the shop, now to get it set up and back to some hobbies!

Looking good. I find with that deep char if I sand it enough to get it smooth and get all of the "shine" off of it glue will adhere just fine. Still a pain in the butt.

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

That wood does look very brittle, good come back. You may have mentioned it before but what are you using to simulate your chalking?

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

hey Ken,  Thanks for stopping in. I use the Sherline lathe, and in this case just rasps, files and sandpaper to do the shaping 

Well it's been a month and I don't have much to show for it. Thanks to all for stopping in, for your likes and great comments. I bought an android box for my TV and have been wasting too much time watching that, great device but be careful!!. Here are some pictures of what little I have accomplished:
These are the completed demizanas and their rack
 

 
This is a before and after shot of the pedestals for the new stand I built. These are some sort of pistons that my favourite son-in-law(my only one) gave to me. I just turned them on the lathe to clean them up and size them, nothing to technical here.
 

Milling the slot for the keel, this is a piece of rosewood
 

This is all the pieces, the base is cherry. I drilled out the brass pedestals and epoxied some 1/8" brass pins in
 

And here it is assembled with four coats of poly. The brass pedestals were given two coats of spray lacquer 
 

These two pictures are showing the railing installed and the demizanas/rack installed
 

Here is a shot of one of the supporting posts down in the hold, complete with dust. lol
 

And this is how she looks this morning
 
Next up are some breast plates(I think that's what they are called) at the bow and stern then a top rail at the stern. Sorry no bow shots, there is some re-contruction going on that I am really not too proud of
Thanks for stopping in and enjoy your day

Ian and Pierre, Thanks for your comments very much appreciated

Thanks Lawrence, great of you to stop by

Hhahahahahaha Mike, You got me laughing on that one. I may need to have a cocktail(drink) to calm down. Good news about the shop, now to get it set up and back to some hobbies!

Good Morning All, Thanks to everyone for stopping in, for your likes and comments. This a new one for me, two updates in a week, but without my vehicle(another story) shipyard time has increased. I have completed the back rails which I will show in my next post as they aren't attached yet and will complete the breast hooks today as Mike is on edge waiting to see them. For now I have nailed the companion way and made some cleats from rosewood.
 

Here I am showing how I mask it to try and get a relatively straight line.
 

Here are a couple of shots showing holes drilled and nails in place. I used .4 mm nylon fishing line. First side I cut these off using flush cutters then sanded smooth, this side I used a sharp blade to cut off then sanded. The blade worked much better and very little sanding was required, just enough to remove excess glue. Should be noted the companion way had several coats of poly on it to prevent any stains from the ca glue.
 

 Here are the results, I think the .4 mm fishing line is the right scale and looks good. With a little more practice I may do a deck someday. I also found some light brown .3 mm fishing line that I may do a test section on my Pegasus with. 
 

Here I'm just showing the steps of making cleats. As you can see they are fairly large about 10 mm so they were fairly easy to make, that's one of the beauties of working at this scale.  The first one is after rough shaping on the Byrnes disc sander and the middle one is after some fine tuning with riffler file the cleat on the right is the kit supplied one. I would not normally spend twenty minutes making a cleat but I only need two so I thought what the heck. As you can see I have two extra ones that I am willing to offer to members here before I list them on ebay 
 

Here I'm rough shaping it on the disc sander.The thing off to the right in the picture is a crepe block used to clean the sanding disc, this helps prolong the life of your disc or belt if you have a thickness sander. You can get these at Lee Valley they are cheap and last forever.
 Thanks once more for stopping in and have a good one.
 

Well it's been a month and I don't have much to show for it. Thanks to all for stopping in, for your likes and great comments. I bought an android box for my TV and have been wasting too much time watching that, great device but be careful!!. Here are some pictures of what little I have accomplished:
These are the completed demizanas and their rack
 

 
This is a before and after shot of the pedestals for the new stand I built. These are some sort of pistons that my favourite son-in-law(my only one) gave to me. I just turned them on the lathe to clean them up and size them, nothing to technical here.
 

Milling the slot for the keel, this is a piece of rosewood
 

This is all the pieces, the base is cherry. I drilled out the brass pedestals and epoxied some 1/8" brass pins in
 

And here it is assembled with four coats of poly. The brass pedestals were given two coats of spray lacquer 
 

These two pictures are showing the railing installed and the demizanas/rack installed
 

Here is a shot of one of the supporting posts down in the hold, complete with dust. lol
 

And this is how she looks this morning
 
Next up are some breast plates(I think that's what they are called) at the bow and stern then a top rail at the stern. Sorry no bow shots, there is some re-contruction going on that I am really not too proud of
Thanks for stopping in and enjoy your day

Looking good. I find with that deep char if I sand it enough to get it smooth and get all of the "shine" off of it glue will adhere just fine. Still a pain in the butt.

That wood does look very brittle, good come back. You may have mentioned it before but what are you using to simulate your chalking?

Well it's been a month and I don't have much to show for it. Thanks to all for stopping in, for your likes and great comments. I bought an android box for my TV and have been wasting too much time watching that, great device but be careful!!. Here are some pictures of what little I have accomplished:
These are the completed demizanas and their rack
 

 
This is a before and after shot of the pedestals for the new stand I built. These are some sort of pistons that my favourite son-in-law(my only one) gave to me. I just turned them on the lathe to clean them up and size them, nothing to technical here.
 

Milling the slot for the keel, this is a piece of rosewood
 

This is all the pieces, the base is cherry. I drilled out the brass pedestals and epoxied some 1/8" brass pins in
 

And here it is assembled with four coats of poly. The brass pedestals were given two coats of spray lacquer 
 

These two pictures are showing the railing installed and the demizanas/rack installed
 

Here is a shot of one of the supporting posts down in the hold, complete with dust. lol
 

And this is how she looks this morning
 
Next up are some breast plates(I think that's what they are called) at the bow and stern then a top rail at the stern. Sorry no bow shots, there is some re-contruction going on that I am really not too proud of
Thanks for stopping in and enjoy your day

Sooooo looking forward to this Bob. Great choice!!

Looking good. I find with that deep char if I sand it enough to get it smooth and get all of the "shine" off of it glue will adhere just fine. Still a pain in the butt.

Hhahahahahaha Mike, You got me laughing on that one. I may need to have a cocktail(drink) to calm down. Good news about the shop, now to get it set up and back to some hobbies!

Thanks Lawrence, great of you to stop by

Ian and Pierre, Thanks for your comments very much appreciated

Beautiful work E.J., you deserve a trip to that lovely shelving unit of yours