shipmodel

After resizing the drawings I needed to modify the building jig, thinking about the sequence of construction I eliminated the keel support for the moment. The white rails were too short so a new pair were drilled.
I had a scrap of Brazilian Rosewood which was just big enough for the new frame end bars. Some wood inserts were driven into the long tubes before the holes were drilled the frame is now quite rigid.
 

 
I have cut the first three new molds for the ribbands and mounted them on the aluminum cross beams.
The molds were cut from 1/4 MDF and are set aft of the station lines, the last two will be set forward of the station Lines.
The molds will not be faired, this why they are placed the way they are.
 

 

 

 
the next pic shows the frame reversed on the build posts. you can see that they are not yet perfectly centered I will do this when all 5 molds are set on the cross beams before adding the keel. I am much happier with the building frame.
 

 

 
I remembered that I had built and stored away a small Dremel routing/sanding table which was fabricated out of 1/4 inch thick black plexiglass.  I used this table a lot when building Architectural models, I set it up for working on the molds along with some curved shaped sanding sticks.
 

 
Michael
 
 
 
 
 
 

I just found out some information about the Lettie.  Back in July, John Cole, here on MSW, started to build America’s cup racer Puritan.  Since Puritan is on my “to build” list, I decided to do some research on her.  She was designed by Edward Burgess who also designed cup racers Mayflower and Volunteer.  About that same time (1888) Burgess was approached to build a schooner.  For two years his schooner won every race it was in.  It was then sold to the fishing fleet.  That boat was the Fredonia.  Because of its speed the Fredonia was copied several times. Those boats were referred to as Fredonia models.  The Lettie G. Howard was the last of the Fredonia models.
 
This is not a model of a brand new boat.  This boat has been around and working for a while, first as a private yacht, then as a cod fisher and finally as a mackerel fisher.  This model is of the mackerel boat.  You’ll notice that the rigging is not consistent.  That is to say the fore mast is not a copy of the main mast etc.  That is because as modifications and changes were made they used what was “at hand” as long as it worked.
 
Now some pictures of the build at present.  A lot of MSW members publish pictures with each add they make.  I don’t seem to be able to do that.  So here are a lot of little things.  Still a long way to go. 
 
Bob
 

Over all
 

Main halyard
 

Fore halyard
 

Jombo jib halyard
 

Bowsprit shrouds
 

Bowsprit
 

Main gaff
 

Fore gaff
 

Spring lines
 
 
 
 

I started working on the funnels.  This proved different in that some of the ways of putting it together were a little varied.
The first thing was to cut it out and begin the assembly.



I was not happy with the stiffness of the material so I glued together a couple of plugs out of stock and wrapped the funnels around them.
The pipe was next.  This stuff needed extra care it was delicate even doubled over.  Once touched up it was glued on.




So far so good.
David B
 

David - 
 
I have lots of photos if they would help.  Feel free to ask and I can get them to you.  It may be easier to run off a disk and mail it to you than to try to email them.  Just send me your address.
 
Dan

David - 
 
I have lots of photos if they would help.  Feel free to ask and I can get them to you.  It may be easier to run off a disk and mail it to you than to try to email them.  Just send me your address.
 
Dan

Hi David - 
 
Coming along quite nicely, given the limitations of the materials.  It is really taking shape.  Don't worry about comparing it to my model or anyone else's.  I know that there are a whole pack of mistakes in my model that, hopefully, I have corrected or covered up.
 
BTW - the 'v' shaped fittings to either side of the gangway between the center and aft deck houses were supports for a pair of large motorized cutters that were never fitted on the ship.  They did find a use for the scaffolding, which was to stow extra spars and even the rolled up set of sails that were originally designed for the ship, in case it ran out of coal in mid-ocean.  Here is one of the earliest plans for the ship, with three masts and raked smokestacks.
 

 
Keep up the good work.  I will be eagerly watching for future installments.
 
Dan
 
 

At the moment I am lucid and able to think so I might be considered sane or normal.  The next thing was to work on the scaffolding.  This is when I really appreciate how delicate this stuff can be and taking very delicate cuts.  
The first thing was to identify and figure out out to do the job.


When getting this thin I was having trouble keeping everything stiff for a straight cut.  So most of it was done using straight edges.


The scaffolding in the front gave me the most problem in getting everything lined up. This involved quite  bit of trial and error until I was able to glue everything down.  I am also touching up the colors as I go.




So far so good.  
David B

I has the most trouble with the main turret wall.  The first time I glued it up it did not fit the base properly in trying to fix it I damaged it.  Fortunately I had scanned the plans earlier just in case,  This time I cut out the opening for the cannons.  The carriage was not acceptable and I redid it. Then I fitted everything and proceeded to put in the cannons.



Then to my surprise the main guns would not fit in their numbered occasions.  After some trial and error.  I found out that for some reason the print mislabeled the assemblies.  Once I reversed the locations I got a god fit.
David B

I then started working on the cannons.  This time even though I followed the plans and studied everything it was a bit tricky.
The first thing was cut out the main parts to build up the base'



Then I started on the barrels.  This is where I deviated a bit.  I was not happy using the card for the core to flimsy.  I took a toothpick and using Jim"s draw plate I brought it down to the right diameter and used that as a core.
After building them up I painted them watercolor.  I thought they were a great improvement.




David B
 
 

Yeah for me...after 11 days and 3 tries, the hawse timbers are cut, assembled, shaped, and installed.  They still need lots of sanding but it's best (from my point of view) to blend into the framing plus there's an inside curve down down low that becomes the outside curve as it rises.  I'm thinking it's best to try it this way.
 
There's also still a ton of fairing to do and I want that done and out of the way before attacking the stern.   So the next update my be awhile. 
 
I'm debating whether to drill out the hawse ports or put in the plugs and leave the anchors unrigged.  My reasoning is that I'm considering full rigging and sails for this one.
 

Hello to all who are following this build -
 
It has been a while since my last posting.  Summertime had a lot to do with it, but I also took some time away to work on a short-term and time critical project.  So here is a little diversion from this build.  It may merit a separate file, but as you will see later on, it is incomplete.
 
I was asked to restore a  presentation model of a modern container ship.  The CMA-CGM Vivaldi was built by Hyundai Samho Heavy Industries Co., Ltd. in their Makpo Shipyard in South Korea.   Launched in December, 2004 she was 334 meters LOA with a breadth of 42.3 m (just under 1100 ft LOA, 140 ft breadth).  Its carrying capacity was not listed on the dimensions plaque on the model, but it is huge.  Here she is in a photo from the company website of CMA-CMG Shipping, which owns and operates her as part of one of the world’s largest fleets of container ships.
 
1
 
The model was likely built in the same shipyard as a gift to thank CMA-CGM for the contract and was presented at the time of launch.  It is built to the small scale of 1:200, but the model is still 5 ½ feet long.  Given that the price for the ship was in the millions of dollars, it is not surprising that a good deal of care went into the construction of this presentation model. 
 
It was probably kept in one of their offices, perhaps in their headquarters in Marseille, for the last decade but then was presented in turn to a financing company in Stamford, Connecticut.  It was during the delivery of the model that things went bad.
 
Here is the crate that it came in.  You can see that although there is no obvious damage to the box itself, one of the bottom cleats is missing. 
 
2
 
I was called in when the box was opened and it was found that one of the glass panels of the case was cracked and there was some damage to the model. My first overall impression was that this was not going to be a hard job.  Some of the containers had been detached from their mountings and were tipped over, but they were still on deck and in a line.  The superstructure was in place and there was no evident damage to the hull.
 
3
 
Closer examination revealed that the devil had been playing in the details.  A large number of small pieces were lying on the blue felt base and some had even become trapped in the channel that the glass case sat in.  Fortunately many of them, including some quite complex assemblies, appeared undamaged like the one in the center of the photo.
 
4
 
 
A repair proposal was discussed, a fee agreed to, and work began with the recovery and conservation of any detached parts.  Once the wrapping of clear plastic was removed the impact point could be seen.  It was clear that there had been one sharp blow which had chipped and cracked the glass panel, but without separating it from the rest of the case. 
 
Unfortunately, this is exactly the kind of impact that cyano glue does not like.  With the help of JerseyCityFrankie the glass cover was removed and all of the loose parts were carefully collected.  The detached container units were numbered from the bow to the stern on sticky notes and set aside.  The grey railing units could not be immediately identified, but they were put into one container for later study.  All of the smaller parts such as the lifeboats, ladders, white railings, and various unknown pieces were put in another.
 
8
9
 
Now the full extent of the damage could be seen and assessed.  Along the edges of the hull most of the railings and stanchions were broken off, leaving unpainted spots showing where they had been attached.  At the stern there was additional damage where the railings and ladders had been crushed and even some pieces of the rigid styrene components had been broken.  When everything that was loose had been removed the deck was almost nude other than two container units at the bow that had somehow managed to remain in place.  This was packed up in bubble wrap and taken back to the studio in Brooklyn, NY.
 
12
 
The superstructure which had initially appeared to be generally sound was found to have suffered the most damage.  In additional to losing both lifeboats, most of the railing on the aft face was gone, as were numerous small parts for the lifeboat cranes.  All of the various radars and antennas on the topmost level were missing.  Most significantly, the starboard bridge wing was broken off almost completely. 
 
13
 
Although the proper locations of many of the pieces could be deduced from what they were, there were a great deal more that could have gone anywhere.  Fortunately the company had a second presentation model of the same ship, the Vivaldi.  A series of photographs were taken of the other model to guide the restoration.
 
Here is the bow, showing the white lookout mast which had been detached on the damaged model.  The ladder and safety cage had been separated and crushed, but now I could see how they had to be repaired.
 
14
 
Those gray railing units turned out to be catwalks that fit between the container units.  They sat on top of U-shaped pieces that supported the containers.  Photoetched ladders gave access to upper catwalks which were bordered by photoetched brass railings.  3-bar railings edged the deck all along the sides of the ship.
 
15a
 
The superstructure had 8 deck levels with a full array of electronic equipment on top.
 
16
 
This area was going to be the most challenging, with radars and antenna that were all made up of very small parts that were quite similar to each other.  The photographs that I was sent were not completely helpful in specifying what went where.  Fortunately, using my Photoshop program I could take the image provided and enlarge it, remove the color, and play with the brightness and contrast until I could see almost all of the details.
 
17
18
 
Now that I had the undamaged model as a guide I could start the actual repairs.  The first thing was to reassemble all of the catwalks.  Some were in pretty good shape, but others had been mauled, with most of the parts separated, some of the plastic parts broken off, and the photoetched brass rails badly bent.  Here is one of the catwalks with all its pieces and a second one after restoration.  There were 21 of these in all, which took up about half of the total restoration time.
 
19
 
Now for the incomplete part -
 
The next several weeks were spent doing the restoration.  I took construction photos as I went, as usual, but had not gotten around to downloading them. [i know you can see the problem coming . . . ]  Soon after I took the last photograph, my daughter and her two boys came over.  One is the newborn, the other 2 years old.  While I was doting on the young one, the other found the camera.  He likes to push buttons.  Enough said. 
 
Let me describe what I did, and I hope you can follow along using photos of the completed repair.
 
All of the least damaged catwalks were put back together.  Since there were small variations in how the bases had broken off of the hull I could locate about two thirds in their original positions, fitting them together like a jigsaw puzzle.  They were numbered and set aside.  One by one the rest were repaired until there were only two left, which were severely bent, with missing parts.  Some replacement parts were fabricated from bent wire, and others from brass shim.  Missing ladders were replaced with similar ones from the spares box.
 
21
 
Starting at the bow and working aft the containers and catwalks were glued to the cleaned up hull.  The containers sit on the corners of the catwalk bases and on a square stanchion between the forward and aft bases located on both edges of the deck.  This gives six attachment points for the double wide containers and four each for the single wide ones.  These also broke off irregularly.  Although each container unit was numbered when it was removed, several ones were out of order, and I had not recorded the orientation of the unit.  Each one was test fit to the proposed location and the irregularities let me confirm the original locations.
 
21a
 
The superstructure was the biggest challenge.  I first relocated the lifeboats and repaired their cranes.  Railings which were bent were carefully bent back and glued.  Some that had been detached were too badly bent to repair.  I had 3-bar railing of the right size in my spares box, but the rails were a bit thinner than those on the model.  I used them to replace the railings that would not be seen easily between the aft face of the superstructure and the container unit behind it.  Then I cannibalized the model railings from that area to replace railings in more obvious locations.
 
22
 
The photos that I miss most are those of the repair of the starboard bridge wing.  Here the impact had broken the brittle styrene that made up the bridge deck and the angled and pierced supports on the fore and aft faces.  The detached pieces had kicked around and were now mostly unusable shards.  I first carefully cut the damaged section away in a straight line across the deck with a miniature keyhole saw.  A piece of similarly thick styrene was cut to fit and glued in and the joint sanded smooth.  Artists acrylic paints were mixed to match the green of the deck  The shape of the aft diagonal support piece was traced from the existing one on the port side and cut out, fitted and finished. It was spray painted gloss white before being installed.  The end cap was similarly fitted.  All joints were cleaned up and touch-up painted.
 
22a
 
Using the photographs of the undamaged model the fittings and fixtures on the upper electronics decks on top of the wheelhouse were located.  Antennas, radars, and lightning rods were all glued in with cyano.  Nothing special here, just a delicate touch and perseverence.
 
23
 
Final small detail parts were installed and all of the spots where paint was chipped or missing were touched up and the model was carefully examined to find bent railings and other defects.  I know that I got almost all of them, but I also know that a few got bye, but I'm not telling where. 
 
A new glass case was ordered and delivered from a local custom glass shop.  So here is the completed model ready for delivery to the customer.  It was driven back to Stamford, CT, with a nervous moment for every pothole and road repair that I couldn't avoid.  It survived completely intact and was installed in the office to gratifying compliments from the customer.
 
24
 
Hope you enjoyed the divertimento.  Getting back to the QAR now.  A new build log post soon.
 
Be well
 
Dan
 
 
 

Hello to all who are following this build -
 
It has been a while since my last posting.  Summertime had a lot to do with it, but I also took some time away to work on a short-term and time critical project.  So here is a little diversion from this build.  It may merit a separate file, but as you will see later on, it is incomplete.
 
I was asked to restore a  presentation model of a modern container ship.  The CMA-CGM Vivaldi was built by Hyundai Samho Heavy Industries Co., Ltd. in their Makpo Shipyard in South Korea.   Launched in December, 2004 she was 334 meters LOA with a breadth of 42.3 m (just under 1100 ft LOA, 140 ft breadth).  Its carrying capacity was not listed on the dimensions plaque on the model, but it is huge.  Here she is in a photo from the company website of CMA-CMG Shipping, which owns and operates her as part of one of the world’s largest fleets of container ships.
 
1
 
The model was likely built in the same shipyard as a gift to thank CMA-CGM for the contract and was presented at the time of launch.  It is built to the small scale of 1:200, but the model is still 5 ½ feet long.  Given that the price for the ship was in the millions of dollars, it is not surprising that a good deal of care went into the construction of this presentation model. 
 
It was probably kept in one of their offices, perhaps in their headquarters in Marseille, for the last decade but then was presented in turn to a financing company in Stamford, Connecticut.  It was during the delivery of the model that things went bad.
 
Here is the crate that it came in.  You can see that although there is no obvious damage to the box itself, one of the bottom cleats is missing. 
 
2
 
I was called in when the box was opened and it was found that one of the glass panels of the case was cracked and there was some damage to the model. My first overall impression was that this was not going to be a hard job.  Some of the containers had been detached from their mountings and were tipped over, but they were still on deck and in a line.  The superstructure was in place and there was no evident damage to the hull.
 
3
 
Closer examination revealed that the devil had been playing in the details.  A large number of small pieces were lying on the blue felt base and some had even become trapped in the channel that the glass case sat in.  Fortunately many of them, including some quite complex assemblies, appeared undamaged like the one in the center of the photo.
 
4
 
 
A repair proposal was discussed, a fee agreed to, and work began with the recovery and conservation of any detached parts.  Once the wrapping of clear plastic was removed the impact point could be seen.  It was clear that there had been one sharp blow which had chipped and cracked the glass panel, but without separating it from the rest of the case. 
 
Unfortunately, this is exactly the kind of impact that cyano glue does not like.  With the help of JerseyCityFrankie the glass cover was removed and all of the loose parts were carefully collected.  The detached container units were numbered from the bow to the stern on sticky notes and set aside.  The grey railing units could not be immediately identified, but they were put into one container for later study.  All of the smaller parts such as the lifeboats, ladders, white railings, and various unknown pieces were put in another.
 
8
9
 
Now the full extent of the damage could be seen and assessed.  Along the edges of the hull most of the railings and stanchions were broken off, leaving unpainted spots showing where they had been attached.  At the stern there was additional damage where the railings and ladders had been crushed and even some pieces of the rigid styrene components had been broken.  When everything that was loose had been removed the deck was almost nude other than two container units at the bow that had somehow managed to remain in place.  This was packed up in bubble wrap and taken back to the studio in Brooklyn, NY.
 
12
 
The superstructure which had initially appeared to be generally sound was found to have suffered the most damage.  In additional to losing both lifeboats, most of the railing on the aft face was gone, as were numerous small parts for the lifeboat cranes.  All of the various radars and antennas on the topmost level were missing.  Most significantly, the starboard bridge wing was broken off almost completely. 
 
13
 
Although the proper locations of many of the pieces could be deduced from what they were, there were a great deal more that could have gone anywhere.  Fortunately the company had a second presentation model of the same ship, the Vivaldi.  A series of photographs were taken of the other model to guide the restoration.
 
Here is the bow, showing the white lookout mast which had been detached on the damaged model.  The ladder and safety cage had been separated and crushed, but now I could see how they had to be repaired.
 
14
 
Those gray railing units turned out to be catwalks that fit between the container units.  They sat on top of U-shaped pieces that supported the containers.  Photoetched ladders gave access to upper catwalks which were bordered by photoetched brass railings.  3-bar railings edged the deck all along the sides of the ship.
 
15a
 
The superstructure had 8 deck levels with a full array of electronic equipment on top.
 
16
 
This area was going to be the most challenging, with radars and antenna that were all made up of very small parts that were quite similar to each other.  The photographs that I was sent were not completely helpful in specifying what went where.  Fortunately, using my Photoshop program I could take the image provided and enlarge it, remove the color, and play with the brightness and contrast until I could see almost all of the details.
 
17
18
 
Now that I had the undamaged model as a guide I could start the actual repairs.  The first thing was to reassemble all of the catwalks.  Some were in pretty good shape, but others had been mauled, with most of the parts separated, some of the plastic parts broken off, and the photoetched brass rails badly bent.  Here is one of the catwalks with all its pieces and a second one after restoration.  There were 21 of these in all, which took up about half of the total restoration time.
 
19
 
Now for the incomplete part -
 
The next several weeks were spent doing the restoration.  I took construction photos as I went, as usual, but had not gotten around to downloading them. [i know you can see the problem coming . . . ]  Soon after I took the last photograph, my daughter and her two boys came over.  One is the newborn, the other 2 years old.  While I was doting on the young one, the other found the camera.  He likes to push buttons.  Enough said. 
 
Let me describe what I did, and I hope you can follow along using photos of the completed repair.
 
All of the least damaged catwalks were put back together.  Since there were small variations in how the bases had broken off of the hull I could locate about two thirds in their original positions, fitting them together like a jigsaw puzzle.  They were numbered and set aside.  One by one the rest were repaired until there were only two left, which were severely bent, with missing parts.  Some replacement parts were fabricated from bent wire, and others from brass shim.  Missing ladders were replaced with similar ones from the spares box.
 
21
 
Starting at the bow and working aft the containers and catwalks were glued to the cleaned up hull.  The containers sit on the corners of the catwalk bases and on a square stanchion between the forward and aft bases located on both edges of the deck.  This gives six attachment points for the double wide containers and four each for the single wide ones.  These also broke off irregularly.  Although each container unit was numbered when it was removed, several ones were out of order, and I had not recorded the orientation of the unit.  Each one was test fit to the proposed location and the irregularities let me confirm the original locations.
 
21a
 
The superstructure was the biggest challenge.  I first relocated the lifeboats and repaired their cranes.  Railings which were bent were carefully bent back and glued.  Some that had been detached were too badly bent to repair.  I had 3-bar railing of the right size in my spares box, but the rails were a bit thinner than those on the model.  I used them to replace the railings that would not be seen easily between the aft face of the superstructure and the container unit behind it.  Then I cannibalized the model railings from that area to replace railings in more obvious locations.
 
22
 
The photos that I miss most are those of the repair of the starboard bridge wing.  Here the impact had broken the brittle styrene that made up the bridge deck and the angled and pierced supports on the fore and aft faces.  The detached pieces had kicked around and were now mostly unusable shards.  I first carefully cut the damaged section away in a straight line across the deck with a miniature keyhole saw.  A piece of similarly thick styrene was cut to fit and glued in and the joint sanded smooth.  Artists acrylic paints were mixed to match the green of the deck  The shape of the aft diagonal support piece was traced from the existing one on the port side and cut out, fitted and finished. It was spray painted gloss white before being installed.  The end cap was similarly fitted.  All joints were cleaned up and touch-up painted.
 
22a
 
Using the photographs of the undamaged model the fittings and fixtures on the upper electronics decks on top of the wheelhouse were located.  Antennas, radars, and lightning rods were all glued in with cyano.  Nothing special here, just a delicate touch and perseverence.
 
23
 
Final small detail parts were installed and all of the spots where paint was chipped or missing were touched up and the model was carefully examined to find bent railings and other defects.  I know that I got almost all of them, but I also know that a few got bye, but I'm not telling where. 
 
A new glass case was ordered and delivered from a local custom glass shop.  So here is the completed model ready for delivery to the customer.  It was driven back to Stamford, CT, with a nervous moment for every pothole and road repair that I couldn't avoid.  It survived completely intact and was installed in the office to gratifying compliments from the customer.
 
24
 
Hope you enjoyed the divertimento.  Getting back to the QAR now.  A new build log post soon.
 
Be well
 
Dan
 
 
 

Hello to all who are following this build -
 
It has been a while since my last posting.  Summertime had a lot to do with it, but I also took some time away to work on a short-term and time critical project.  So here is a little diversion from this build.  It may merit a separate file, but as you will see later on, it is incomplete.
 
I was asked to restore a  presentation model of a modern container ship.  The CMA-CGM Vivaldi was built by Hyundai Samho Heavy Industries Co., Ltd. in their Makpo Shipyard in South Korea.   Launched in December, 2004 she was 334 meters LOA with a breadth of 42.3 m (just under 1100 ft LOA, 140 ft breadth).  Its carrying capacity was not listed on the dimensions plaque on the model, but it is huge.  Here she is in a photo from the company website of CMA-CMG Shipping, which owns and operates her as part of one of the world’s largest fleets of container ships.
 
1
 
The model was likely built in the same shipyard as a gift to thank CMA-CGM for the contract and was presented at the time of launch.  It is built to the small scale of 1:200, but the model is still 5 ½ feet long.  Given that the price for the ship was in the millions of dollars, it is not surprising that a good deal of care went into the construction of this presentation model. 
 
It was probably kept in one of their offices, perhaps in their headquarters in Marseille, for the last decade but then was presented in turn to a financing company in Stamford, Connecticut.  It was during the delivery of the model that things went bad.
 
Here is the crate that it came in.  You can see that although there is no obvious damage to the box itself, one of the bottom cleats is missing. 
 
2
 
I was called in when the box was opened and it was found that one of the glass panels of the case was cracked and there was some damage to the model. My first overall impression was that this was not going to be a hard job.  Some of the containers had been detached from their mountings and were tipped over, but they were still on deck and in a line.  The superstructure was in place and there was no evident damage to the hull.
 
3
 
Closer examination revealed that the devil had been playing in the details.  A large number of small pieces were lying on the blue felt base and some had even become trapped in the channel that the glass case sat in.  Fortunately many of them, including some quite complex assemblies, appeared undamaged like the one in the center of the photo.
 
4
 
 
A repair proposal was discussed, a fee agreed to, and work began with the recovery and conservation of any detached parts.  Once the wrapping of clear plastic was removed the impact point could be seen.  It was clear that there had been one sharp blow which had chipped and cracked the glass panel, but without separating it from the rest of the case. 
 
Unfortunately, this is exactly the kind of impact that cyano glue does not like.  With the help of JerseyCityFrankie the glass cover was removed and all of the loose parts were carefully collected.  The detached container units were numbered from the bow to the stern on sticky notes and set aside.  The grey railing units could not be immediately identified, but they were put into one container for later study.  All of the smaller parts such as the lifeboats, ladders, white railings, and various unknown pieces were put in another.
 
8
9
 
Now the full extent of the damage could be seen and assessed.  Along the edges of the hull most of the railings and stanchions were broken off, leaving unpainted spots showing where they had been attached.  At the stern there was additional damage where the railings and ladders had been crushed and even some pieces of the rigid styrene components had been broken.  When everything that was loose had been removed the deck was almost nude other than two container units at the bow that had somehow managed to remain in place.  This was packed up in bubble wrap and taken back to the studio in Brooklyn, NY.
 
12
 
The superstructure which had initially appeared to be generally sound was found to have suffered the most damage.  In additional to losing both lifeboats, most of the railing on the aft face was gone, as were numerous small parts for the lifeboat cranes.  All of the various radars and antennas on the topmost level were missing.  Most significantly, the starboard bridge wing was broken off almost completely. 
 
13
 
Although the proper locations of many of the pieces could be deduced from what they were, there were a great deal more that could have gone anywhere.  Fortunately the company had a second presentation model of the same ship, the Vivaldi.  A series of photographs were taken of the other model to guide the restoration.
 
Here is the bow, showing the white lookout mast which had been detached on the damaged model.  The ladder and safety cage had been separated and crushed, but now I could see how they had to be repaired.
 
14
 
Those gray railing units turned out to be catwalks that fit between the container units.  They sat on top of U-shaped pieces that supported the containers.  Photoetched ladders gave access to upper catwalks which were bordered by photoetched brass railings.  3-bar railings edged the deck all along the sides of the ship.
 
15a
 
The superstructure had 8 deck levels with a full array of electronic equipment on top.
 
16
 
This area was going to be the most challenging, with radars and antenna that were all made up of very small parts that were quite similar to each other.  The photographs that I was sent were not completely helpful in specifying what went where.  Fortunately, using my Photoshop program I could take the image provided and enlarge it, remove the color, and play with the brightness and contrast until I could see almost all of the details.
 
17
18
 
Now that I had the undamaged model as a guide I could start the actual repairs.  The first thing was to reassemble all of the catwalks.  Some were in pretty good shape, but others had been mauled, with most of the parts separated, some of the plastic parts broken off, and the photoetched brass rails badly bent.  Here is one of the catwalks with all its pieces and a second one after restoration.  There were 21 of these in all, which took up about half of the total restoration time.
 
19
 
Now for the incomplete part -
 
The next several weeks were spent doing the restoration.  I took construction photos as I went, as usual, but had not gotten around to downloading them. [i know you can see the problem coming . . . ]  Soon after I took the last photograph, my daughter and her two boys came over.  One is the newborn, the other 2 years old.  While I was doting on the young one, the other found the camera.  He likes to push buttons.  Enough said. 
 
Let me describe what I did, and I hope you can follow along using photos of the completed repair.
 
All of the least damaged catwalks were put back together.  Since there were small variations in how the bases had broken off of the hull I could locate about two thirds in their original positions, fitting them together like a jigsaw puzzle.  They were numbered and set aside.  One by one the rest were repaired until there were only two left, which were severely bent, with missing parts.  Some replacement parts were fabricated from bent wire, and others from brass shim.  Missing ladders were replaced with similar ones from the spares box.
 
21
 
Starting at the bow and working aft the containers and catwalks were glued to the cleaned up hull.  The containers sit on the corners of the catwalk bases and on a square stanchion between the forward and aft bases located on both edges of the deck.  This gives six attachment points for the double wide containers and four each for the single wide ones.  These also broke off irregularly.  Although each container unit was numbered when it was removed, several ones were out of order, and I had not recorded the orientation of the unit.  Each one was test fit to the proposed location and the irregularities let me confirm the original locations.
 
21a
 
The superstructure was the biggest challenge.  I first relocated the lifeboats and repaired their cranes.  Railings which were bent were carefully bent back and glued.  Some that had been detached were too badly bent to repair.  I had 3-bar railing of the right size in my spares box, but the rails were a bit thinner than those on the model.  I used them to replace the railings that would not be seen easily between the aft face of the superstructure and the container unit behind it.  Then I cannibalized the model railings from that area to replace railings in more obvious locations.
 
22
 
The photos that I miss most are those of the repair of the starboard bridge wing.  Here the impact had broken the brittle styrene that made up the bridge deck and the angled and pierced supports on the fore and aft faces.  The detached pieces had kicked around and were now mostly unusable shards.  I first carefully cut the damaged section away in a straight line across the deck with a miniature keyhole saw.  A piece of similarly thick styrene was cut to fit and glued in and the joint sanded smooth.  Artists acrylic paints were mixed to match the green of the deck  The shape of the aft diagonal support piece was traced from the existing one on the port side and cut out, fitted and finished. It was spray painted gloss white before being installed.  The end cap was similarly fitted.  All joints were cleaned up and touch-up painted.
 
22a
 
Using the photographs of the undamaged model the fittings and fixtures on the upper electronics decks on top of the wheelhouse were located.  Antennas, radars, and lightning rods were all glued in with cyano.  Nothing special here, just a delicate touch and perseverence.
 
23
 
Final small detail parts were installed and all of the spots where paint was chipped or missing were touched up and the model was carefully examined to find bent railings and other defects.  I know that I got almost all of them, but I also know that a few got bye, but I'm not telling where. 
 
A new glass case was ordered and delivered from a local custom glass shop.  So here is the completed model ready for delivery to the customer.  It was driven back to Stamford, CT, with a nervous moment for every pothole and road repair that I couldn't avoid.  It survived completely intact and was installed in the office to gratifying compliments from the customer.
 
24
 
Hope you enjoyed the divertimento.  Getting back to the QAR now.  A new build log post soon.
 
Be well
 
Dan
 
 
 

Hello to all who are following this build -
 
It has been a while since my last posting.  Summertime had a lot to do with it, but I also took some time away to work on a short-term and time critical project.  So here is a little diversion from this build.  It may merit a separate file, but as you will see later on, it is incomplete.
 
I was asked to restore a  presentation model of a modern container ship.  The CMA-CGM Vivaldi was built by Hyundai Samho Heavy Industries Co., Ltd. in their Makpo Shipyard in South Korea.   Launched in December, 2004 she was 334 meters LOA with a breadth of 42.3 m (just under 1100 ft LOA, 140 ft breadth).  Its carrying capacity was not listed on the dimensions plaque on the model, but it is huge.  Here she is in a photo from the company website of CMA-CMG Shipping, which owns and operates her as part of one of the world’s largest fleets of container ships.
 
1
 
The model was likely built in the same shipyard as a gift to thank CMA-CGM for the contract and was presented at the time of launch.  It is built to the small scale of 1:200, but the model is still 5 ½ feet long.  Given that the price for the ship was in the millions of dollars, it is not surprising that a good deal of care went into the construction of this presentation model. 
 
It was probably kept in one of their offices, perhaps in their headquarters in Marseille, for the last decade but then was presented in turn to a financing company in Stamford, Connecticut.  It was during the delivery of the model that things went bad.
 
Here is the crate that it came in.  You can see that although there is no obvious damage to the box itself, one of the bottom cleats is missing. 
 
2
 
I was called in when the box was opened and it was found that one of the glass panels of the case was cracked and there was some damage to the model. My first overall impression was that this was not going to be a hard job.  Some of the containers had been detached from their mountings and were tipped over, but they were still on deck and in a line.  The superstructure was in place and there was no evident damage to the hull.
 
3
 
Closer examination revealed that the devil had been playing in the details.  A large number of small pieces were lying on the blue felt base and some had even become trapped in the channel that the glass case sat in.  Fortunately many of them, including some quite complex assemblies, appeared undamaged like the one in the center of the photo.
 
4
 
 
A repair proposal was discussed, a fee agreed to, and work began with the recovery and conservation of any detached parts.  Once the wrapping of clear plastic was removed the impact point could be seen.  It was clear that there had been one sharp blow which had chipped and cracked the glass panel, but without separating it from the rest of the case. 
 
Unfortunately, this is exactly the kind of impact that cyano glue does not like.  With the help of JerseyCityFrankie the glass cover was removed and all of the loose parts were carefully collected.  The detached container units were numbered from the bow to the stern on sticky notes and set aside.  The grey railing units could not be immediately identified, but they were put into one container for later study.  All of the smaller parts such as the lifeboats, ladders, white railings, and various unknown pieces were put in another.
 
8
9
 
Now the full extent of the damage could be seen and assessed.  Along the edges of the hull most of the railings and stanchions were broken off, leaving unpainted spots showing where they had been attached.  At the stern there was additional damage where the railings and ladders had been crushed and even some pieces of the rigid styrene components had been broken.  When everything that was loose had been removed the deck was almost nude other than two container units at the bow that had somehow managed to remain in place.  This was packed up in bubble wrap and taken back to the studio in Brooklyn, NY.
 
12
 
The superstructure which had initially appeared to be generally sound was found to have suffered the most damage.  In additional to losing both lifeboats, most of the railing on the aft face was gone, as were numerous small parts for the lifeboat cranes.  All of the various radars and antennas on the topmost level were missing.  Most significantly, the starboard bridge wing was broken off almost completely. 
 
13
 
Although the proper locations of many of the pieces could be deduced from what they were, there were a great deal more that could have gone anywhere.  Fortunately the company had a second presentation model of the same ship, the Vivaldi.  A series of photographs were taken of the other model to guide the restoration.
 
Here is the bow, showing the white lookout mast which had been detached on the damaged model.  The ladder and safety cage had been separated and crushed, but now I could see how they had to be repaired.
 
14
 
Those gray railing units turned out to be catwalks that fit between the container units.  They sat on top of U-shaped pieces that supported the containers.  Photoetched ladders gave access to upper catwalks which were bordered by photoetched brass railings.  3-bar railings edged the deck all along the sides of the ship.
 
15a
 
The superstructure had 8 deck levels with a full array of electronic equipment on top.
 
16
 
This area was going to be the most challenging, with radars and antenna that were all made up of very small parts that were quite similar to each other.  The photographs that I was sent were not completely helpful in specifying what went where.  Fortunately, using my Photoshop program I could take the image provided and enlarge it, remove the color, and play with the brightness and contrast until I could see almost all of the details.
 
17
18
 
Now that I had the undamaged model as a guide I could start the actual repairs.  The first thing was to reassemble all of the catwalks.  Some were in pretty good shape, but others had been mauled, with most of the parts separated, some of the plastic parts broken off, and the photoetched brass rails badly bent.  Here is one of the catwalks with all its pieces and a second one after restoration.  There were 21 of these in all, which took up about half of the total restoration time.
 
19
 
Now for the incomplete part -
 
The next several weeks were spent doing the restoration.  I took construction photos as I went, as usual, but had not gotten around to downloading them. [i know you can see the problem coming . . . ]  Soon after I took the last photograph, my daughter and her two boys came over.  One is the newborn, the other 2 years old.  While I was doting on the young one, the other found the camera.  He likes to push buttons.  Enough said. 
 
Let me describe what I did, and I hope you can follow along using photos of the completed repair.
 
All of the least damaged catwalks were put back together.  Since there were small variations in how the bases had broken off of the hull I could locate about two thirds in their original positions, fitting them together like a jigsaw puzzle.  They were numbered and set aside.  One by one the rest were repaired until there were only two left, which were severely bent, with missing parts.  Some replacement parts were fabricated from bent wire, and others from brass shim.  Missing ladders were replaced with similar ones from the spares box.
 
21
 
Starting at the bow and working aft the containers and catwalks were glued to the cleaned up hull.  The containers sit on the corners of the catwalk bases and on a square stanchion between the forward and aft bases located on both edges of the deck.  This gives six attachment points for the double wide containers and four each for the single wide ones.  These also broke off irregularly.  Although each container unit was numbered when it was removed, several ones were out of order, and I had not recorded the orientation of the unit.  Each one was test fit to the proposed location and the irregularities let me confirm the original locations.
 
21a
 
The superstructure was the biggest challenge.  I first relocated the lifeboats and repaired their cranes.  Railings which were bent were carefully bent back and glued.  Some that had been detached were too badly bent to repair.  I had 3-bar railing of the right size in my spares box, but the rails were a bit thinner than those on the model.  I used them to replace the railings that would not be seen easily between the aft face of the superstructure and the container unit behind it.  Then I cannibalized the model railings from that area to replace railings in more obvious locations.
 
22
 
The photos that I miss most are those of the repair of the starboard bridge wing.  Here the impact had broken the brittle styrene that made up the bridge deck and the angled and pierced supports on the fore and aft faces.  The detached pieces had kicked around and were now mostly unusable shards.  I first carefully cut the damaged section away in a straight line across the deck with a miniature keyhole saw.  A piece of similarly thick styrene was cut to fit and glued in and the joint sanded smooth.  Artists acrylic paints were mixed to match the green of the deck  The shape of the aft diagonal support piece was traced from the existing one on the port side and cut out, fitted and finished. It was spray painted gloss white before being installed.  The end cap was similarly fitted.  All joints were cleaned up and touch-up painted.
 
22a
 
Using the photographs of the undamaged model the fittings and fixtures on the upper electronics decks on top of the wheelhouse were located.  Antennas, radars, and lightning rods were all glued in with cyano.  Nothing special here, just a delicate touch and perseverence.
 
23
 
Final small detail parts were installed and all of the spots where paint was chipped or missing were touched up and the model was carefully examined to find bent railings and other defects.  I know that I got almost all of them, but I also know that a few got bye, but I'm not telling where. 
 
A new glass case was ordered and delivered from a local custom glass shop.  So here is the completed model ready for delivery to the customer.  It was driven back to Stamford, CT, with a nervous moment for every pothole and road repair that I couldn't avoid.  It survived completely intact and was installed in the office to gratifying compliments from the customer.
 
24
 
Hope you enjoyed the divertimento.  Getting back to the QAR now.  A new build log post soon.
 
Be well
 
Dan
 
 
 

Hello to all who are following this build -
 
It has been a while since my last posting.  Summertime had a lot to do with it, but I also took some time away to work on a short-term and time critical project.  So here is a little diversion from this build.  It may merit a separate file, but as you will see later on, it is incomplete.
 
I was asked to restore a  presentation model of a modern container ship.  The CMA-CGM Vivaldi was built by Hyundai Samho Heavy Industries Co., Ltd. in their Makpo Shipyard in South Korea.   Launched in December, 2004 she was 334 meters LOA with a breadth of 42.3 m (just under 1100 ft LOA, 140 ft breadth).  Its carrying capacity was not listed on the dimensions plaque on the model, but it is huge.  Here she is in a photo from the company website of CMA-CMG Shipping, which owns and operates her as part of one of the world’s largest fleets of container ships.
 
1
 
The model was likely built in the same shipyard as a gift to thank CMA-CGM for the contract and was presented at the time of launch.  It is built to the small scale of 1:200, but the model is still 5 ½ feet long.  Given that the price for the ship was in the millions of dollars, it is not surprising that a good deal of care went into the construction of this presentation model. 
 
It was probably kept in one of their offices, perhaps in their headquarters in Marseille, for the last decade but then was presented in turn to a financing company in Stamford, Connecticut.  It was during the delivery of the model that things went bad.
 
Here is the crate that it came in.  You can see that although there is no obvious damage to the box itself, one of the bottom cleats is missing. 
 
2
 
I was called in when the box was opened and it was found that one of the glass panels of the case was cracked and there was some damage to the model. My first overall impression was that this was not going to be a hard job.  Some of the containers had been detached from their mountings and were tipped over, but they were still on deck and in a line.  The superstructure was in place and there was no evident damage to the hull.
 
3
 
Closer examination revealed that the devil had been playing in the details.  A large number of small pieces were lying on the blue felt base and some had even become trapped in the channel that the glass case sat in.  Fortunately many of them, including some quite complex assemblies, appeared undamaged like the one in the center of the photo.
 
4
 
 
A repair proposal was discussed, a fee agreed to, and work began with the recovery and conservation of any detached parts.  Once the wrapping of clear plastic was removed the impact point could be seen.  It was clear that there had been one sharp blow which had chipped and cracked the glass panel, but without separating it from the rest of the case. 
 
Unfortunately, this is exactly the kind of impact that cyano glue does not like.  With the help of JerseyCityFrankie the glass cover was removed and all of the loose parts were carefully collected.  The detached container units were numbered from the bow to the stern on sticky notes and set aside.  The grey railing units could not be immediately identified, but they were put into one container for later study.  All of the smaller parts such as the lifeboats, ladders, white railings, and various unknown pieces were put in another.
 
8
9
 
Now the full extent of the damage could be seen and assessed.  Along the edges of the hull most of the railings and stanchions were broken off, leaving unpainted spots showing where they had been attached.  At the stern there was additional damage where the railings and ladders had been crushed and even some pieces of the rigid styrene components had been broken.  When everything that was loose had been removed the deck was almost nude other than two container units at the bow that had somehow managed to remain in place.  This was packed up in bubble wrap and taken back to the studio in Brooklyn, NY.
 
12
 
The superstructure which had initially appeared to be generally sound was found to have suffered the most damage.  In additional to losing both lifeboats, most of the railing on the aft face was gone, as were numerous small parts for the lifeboat cranes.  All of the various radars and antennas on the topmost level were missing.  Most significantly, the starboard bridge wing was broken off almost completely. 
 
13
 
Although the proper locations of many of the pieces could be deduced from what they were, there were a great deal more that could have gone anywhere.  Fortunately the company had a second presentation model of the same ship, the Vivaldi.  A series of photographs were taken of the other model to guide the restoration.
 
Here is the bow, showing the white lookout mast which had been detached on the damaged model.  The ladder and safety cage had been separated and crushed, but now I could see how they had to be repaired.
 
14
 
Those gray railing units turned out to be catwalks that fit between the container units.  They sat on top of U-shaped pieces that supported the containers.  Photoetched ladders gave access to upper catwalks which were bordered by photoetched brass railings.  3-bar railings edged the deck all along the sides of the ship.
 
15a
 
The superstructure had 8 deck levels with a full array of electronic equipment on top.
 
16
 
This area was going to be the most challenging, with radars and antenna that were all made up of very small parts that were quite similar to each other.  The photographs that I was sent were not completely helpful in specifying what went where.  Fortunately, using my Photoshop program I could take the image provided and enlarge it, remove the color, and play with the brightness and contrast until I could see almost all of the details.
 
17
18
 
Now that I had the undamaged model as a guide I could start the actual repairs.  The first thing was to reassemble all of the catwalks.  Some were in pretty good shape, but others had been mauled, with most of the parts separated, some of the plastic parts broken off, and the photoetched brass rails badly bent.  Here is one of the catwalks with all its pieces and a second one after restoration.  There were 21 of these in all, which took up about half of the total restoration time.
 
19
 
Now for the incomplete part -
 
The next several weeks were spent doing the restoration.  I took construction photos as I went, as usual, but had not gotten around to downloading them. [i know you can see the problem coming . . . ]  Soon after I took the last photograph, my daughter and her two boys came over.  One is the newborn, the other 2 years old.  While I was doting on the young one, the other found the camera.  He likes to push buttons.  Enough said. 
 
Let me describe what I did, and I hope you can follow along using photos of the completed repair.
 
All of the least damaged catwalks were put back together.  Since there were small variations in how the bases had broken off of the hull I could locate about two thirds in their original positions, fitting them together like a jigsaw puzzle.  They were numbered and set aside.  One by one the rest were repaired until there were only two left, which were severely bent, with missing parts.  Some replacement parts were fabricated from bent wire, and others from brass shim.  Missing ladders were replaced with similar ones from the spares box.
 
21
 
Starting at the bow and working aft the containers and catwalks were glued to the cleaned up hull.  The containers sit on the corners of the catwalk bases and on a square stanchion between the forward and aft bases located on both edges of the deck.  This gives six attachment points for the double wide containers and four each for the single wide ones.  These also broke off irregularly.  Although each container unit was numbered when it was removed, several ones were out of order, and I had not recorded the orientation of the unit.  Each one was test fit to the proposed location and the irregularities let me confirm the original locations.
 
21a
 
The superstructure was the biggest challenge.  I first relocated the lifeboats and repaired their cranes.  Railings which were bent were carefully bent back and glued.  Some that had been detached were too badly bent to repair.  I had 3-bar railing of the right size in my spares box, but the rails were a bit thinner than those on the model.  I used them to replace the railings that would not be seen easily between the aft face of the superstructure and the container unit behind it.  Then I cannibalized the model railings from that area to replace railings in more obvious locations.
 
22
 
The photos that I miss most are those of the repair of the starboard bridge wing.  Here the impact had broken the brittle styrene that made up the bridge deck and the angled and pierced supports on the fore and aft faces.  The detached pieces had kicked around and were now mostly unusable shards.  I first carefully cut the damaged section away in a straight line across the deck with a miniature keyhole saw.  A piece of similarly thick styrene was cut to fit and glued in and the joint sanded smooth.  Artists acrylic paints were mixed to match the green of the deck  The shape of the aft diagonal support piece was traced from the existing one on the port side and cut out, fitted and finished. It was spray painted gloss white before being installed.  The end cap was similarly fitted.  All joints were cleaned up and touch-up painted.
 
22a
 
Using the photographs of the undamaged model the fittings and fixtures on the upper electronics decks on top of the wheelhouse were located.  Antennas, radars, and lightning rods were all glued in with cyano.  Nothing special here, just a delicate touch and perseverence.
 
23
 
Final small detail parts were installed and all of the spots where paint was chipped or missing were touched up and the model was carefully examined to find bent railings and other defects.  I know that I got almost all of them, but I also know that a few got bye, but I'm not telling where. 
 
A new glass case was ordered and delivered from a local custom glass shop.  So here is the completed model ready for delivery to the customer.  It was driven back to Stamford, CT, with a nervous moment for every pothole and road repair that I couldn't avoid.  It survived completely intact and was installed in the office to gratifying compliments from the customer.
 
24
 
Hope you enjoyed the divertimento.  Getting back to the QAR now.  A new build log post soon.
 
Be well
 
Dan
 
 
 

Hi again, and best wishes for a happy Friday the 13th –
 
Thanks for the compliments, likes, and wishes for my new grandson.  Caleb and his mother are both doing well and send their thanks as well.
 
Several smaller items were completed in this segment.  The first was the forward bulkhead for the captain’s cabin.  There are no plans or drawings of it in either of the plans that I am using, so I designed it to be functional, using some of the same details as on the stern and quarter badges. 
 

 
There is a chair rail molding with wainscoting below.  This was not scribed but laid up from individual planks.  The door is of a typical 17th Century style, with H-L hinges and decorative cross banding.  The windows are flanked by fluted columns which were built up as before.  To each side there will be a ladder to the poop deck, which have not yet been constructed.  The bulkhead is still removable at this stage, and may have to be moved back a little to give me room to install the whipstaff which will go between the cabin and the mizzen mast.
 
I have not decided whether to paint the wainscoting blue and add some decorative details.  What does the group think?
 
The cabin was also dressed up by closing in the aftmost gunport with a decorative shutter.  The central circle was made by stiffening a 1/8” birch dowel with a drop of thin cyano on its cut end.  When dry the center of the dowel was drilled out to a depth of about ¼” and then the circles were parted off on the table saw.
 

 
Next I turned to the first of the rigging fixtures – the staghorns.  Here is a section of my plans for the inner bulwarks, which was made by using PhotoShop to combine the plans from the Advice Prize with details from Le Mercure.  You can see three of the four staghorns that will be mounted on each side.
 

 
Here is an enlargement of the plans for the staghorns.  Note in the side view the extreme angles that have to be used to match the 13 degree tumblehome of the bulwarks.
 

 
I started by carving a length of pear to the shape of the horns of the fitting.  The piece was just under 3 inches long, which gave me extra material for the next model as well.  Here you can see three horns that have been parted off.  They are a little heavy, but were later reduced with a small sanding drum.
 

 
The shelf that supports the horns was built up in two parts.  In the larger, back piece, two notches were nibbled out for the horns before being closed in by the front piece.  In the insert enlargement you can see how the curve of the table saw blade gave me an angle to the back of the notch that is needed to allow the horns to angle to match the tumblehome.
 

 
With the horns inserted in the shelf the bottom piece had two notches hollowed out in its back face for the lower ends of the horns.
 

 
The lower piece was flipped over and the horns glued into the notches.  The lower piece was then sanded to its clamshell shape and the upper ends of the horns were refined to angle up and out.  You can see the differences from the left fitting to the completed one on the right.
 

 
Here you can see a finished staghorn sitting on an angled scrap block to check that the shelf will be horizontal when mounted on the bulwark.
 

 
Here is the complete set of eight staghorns for the first model.
 

 
And here is the first one mounted in the waist ready for the lines that run through the hull sheaves for the main and spritsail sheets.
 

 
Next I turned to the gunport lids for the open gunports on the port side of the ship.  I have detailed their construction before in the section on the test gun station.  This one is for the forwardmost port, which is why the planking runs at an angle to match the hull planking.  The hinge straps are blackened brass strip secured with three iron pins.  The ends of the strips were ground to about half their width so they could fit into mounting holes in the hull.
 

 
The strips were all made to a uniform size in a simple jig.  A brass strip was trapped between two guides and the locations of the holes for the mounting pins was marked off.  Once the holes were drilled the strip was clipped to length at the edge of the jig.  I found that without pre-drilling these holes it was nearly impossible for me to drill them cleanly once the hinge strap was mounted on the gunport lid.
 

 
Each lid was marked for its proper location and the mounting holes were drilled just above the open gunport.  With the lids slid into the holes the brass could be gently bent so every lid was at the same angle.  This will be a significant advantage once they are permanently mounted, as they will be much less prone to snapping off when I bump into them (which I am sure that I will).  Here they are towards the bow - - -
 

 
And the stern.
 

 
To check them, I set the guns in place.  Here is what they look like in the waist as seen from outboard - - -
 

 
And along the length of the ship.
 

 
Finally, the entire broadside. 
 

 
I was happy with the look of the model, so the guns and gunport lids were removed to safe storage until the interior deck fittings are built and mounted.
 
The first of these was the riding bitts for the anchor cable.  As you can see from the plans it incorporates the 5-sheave post for the rigging to the ramshead block that raises and lowers the foreyard.
 

 
Construction was straightforward, with each piece cut and shaped, then notched and pinned in place.  The sheaves in the post are non-working, and made by drilling 5 pairs of holes through the post with a 0.040” drill in a miniature drill press.  The bitt was then put into a Dremel and the sheave slot between the holes was carved out.  Care has to be taken to allow for the right-hand torque of the bitt, but a little practice yields good results.
 

 
The next rigging fitting that I turned to were the multiple cleat ‘logs’ that sit just aft of the fore and main masts.  These were discussed earlier in the build log as well. 
 
Construction here was straightforward as well.  Once the dimensions were decided, two pieces of cherry were cut and the ends finished with slopes.  The underside of each was sanded to match the camber of the deck.  Ten slots were cut in the underside for the lines to run through.  It is quite probably that these slots would have been radiused on each side of the log so the line would run smoothly under the fixture.  The upper corners of the log were eased as well, as recommended by JerseyCityFrankie.  Matching photoetched brass cleats were obtained from Bluejacket, blackened and mounted. 
 

 
Here is the one on the quarterdeck aft of the main mast.  It looks good as is, although I clearly have to clean the deck which is getting very dusty.
 

 
Finally, to check that things are headed in the right direction, and to give my spirits a needed lift, I mounted the decks and the lower masts.  Hull construction and detailing have taken much, much longer than anticipated, but I can see some light at the end of the tunnel.  I just hope that it is not the oncoming train known as “RIGGING”.
 

 
Be well
 
Dan
 
 
 

David,
 
The part you are confused about is the inner superstructure wall.  You actually have the part upside down in the photo - the small panel on the far right goes to the left of the 6 in gun mount.  The second panel must be curved to fit in front of the gun mount.  Here are inboard and outboard pics of the area in question - hope these are of use to you.
 

The next item was the hull.  The sides were two parts each. The first thing was to cut them out and glue them together.
I used a piece of scrap on the back at the joint and a straight edge to make sure it was lined up properly.




Then I cut out and applied the accents.  This part was the nerve racking part where a steady hand and a sharp scalpel came in handy.




David B
 
 

I have been able to get some more into the Maine and was able to finish off the two cabins.
And here is where I found that rubbing alcohol can be your best friend. 
While fitting the roof of the forward cabin I noticed that the walls were not fully aligned.  By using a brush and a drop of rubbing alcohol I was able to reposition everything for a better fit.  Plus the alcohol evaporated quickly and did not stain or damage the material.  Once the roof was placed to my satisfaction I glued it down using a weight to hold it until the glue dried.  Then a little touch up with a brush and it is about as good as I can make it.
.






David B
 

Well, this was already described at this thread, just have a look:
 
http://modelshipworld.com/index.php/topic/854-royal-caroline-by-doris-card-1749-140/?p=162240
 
 
And what´s new on the model.....
I have just started with masts and rigging, I try to make all these things according to plans from Anatomy of RC and also follow books and other credible information to achieve more realistic result.
 
The bowsprit:
 




 
The ropes are handmade using the ropewalk. I use ropes by Corel or Amati...

Hi David -
 
I haven't appreciated card models very much before this, but this one seems to be quite accurate.  You are doing a very neat job too.  Looking good.
 
The curved front pieces that you just assembled are not the turret itself.  They are a set of six hinged doors.  A 5 inch gun is mounted on a rotating base behind them.  The barrel extends snugly through the large black dot (hole) at the corner of 4 of the doors.  In combat the doors would all be opened to allow the barrel to traverse and elevate.  There is a matching pair at the stern as well.
 

 
I am following your progress with great interest.
 
Dan

Hi David -
 
I haven't appreciated card models very much before this, but this one seems to be quite accurate.  You are doing a very neat job too.  Looking good.
 
The curved front pieces that you just assembled are not the turret itself.  They are a set of six hinged doors.  A 5 inch gun is mounted on a rotating base behind them.  The barrel extends snugly through the large black dot (hole) at the corner of 4 of the doors.  In combat the doors would all be opened to allow the barrel to traverse and elevate.  There is a matching pair at the stern as well.
 

 
I am following your progress with great interest.
 
Dan

Hi David -
 
I haven't appreciated card models very much before this, but this one seems to be quite accurate.  You are doing a very neat job too.  Looking good.
 
The curved front pieces that you just assembled are not the turret itself.  They are a set of six hinged doors.  A 5 inch gun is mounted on a rotating base behind them.  The barrel extends snugly through the large black dot (hole) at the corner of 4 of the doors.  In combat the doors would all be opened to allow the barrel to traverse and elevate.  There is a matching pair at the stern as well.
 

 
I am following your progress with great interest.
 
Dan

The next piece of business was the roofs of the for and aft cabins.  Basically cut them out and put in the plugs for the holds.
This was straight forward just keep a steady hand and a sharp knife.  The holds were put together by folding them and adding a piece of paper to the back to aid in the glue up.  Then everything was glued together






David B

Before I finished the house I cut out the Aufbauwand hinten and started building it up.  The first part was the easiest just fold and attach to the wall.





 
David B