Blacky

Thanks @allanyed. I think you are right. Now that the first layer is finished i think it is safe to trim the first three to the right dimension.

But first, sanding, cutting the gunports and then i am moving to the interior. I also plan to do custom version of the agamemnon figurine but all in its time

Does anyone know if this bulkhead width is correct? This would mean that the inner line is not parallel with the outer. 

Another update

On 4/15/2024 at 4:29 PM, ccoyle said:

 

I would expect them to be very minimal, as was typical for the early Caldercraft/Nelson's Navy kits.

Yes, very minimal. Blueprints and few pages of text

Update, still working on the first layer. Using methods that Chuck explained and adjusting them as suits me. Should be more than good enough forthe first planking layer. I want it to be solid base for the second layer and get the curves right. 

I have followed instructions for the upper half. Now i have to figure the best way to plank the rest. Feel free to comment.

Edit: just cant get the picture right on my smartphone

Little update. 

Aaand the first plank goes on 🍻 

Checking bulkheads one more time and adding some width so the planking goes as smooth as it can be. I am suprised that the bulkheads have so much error. 

Lower gun deck painted in black to reduce visibility since there are only gun barrels. I plan to plank only middle part that can be seen through the upper deck. Last two bulkheads are finally glued so i can't work on it today anymore.

Frame for the lower cabin is also glued and reinforced and I also managed to cut the 0.8 plywood for the floor. The original plywood (which wasn't included in the set,  i think the one i got is for hms victory) stops at the cabin so i had to extend the deck. I contacted Jotika support and they told me that they cannot sent me missing part directly if i dont spend 150£. 

New bulkhead fits perfectly. Cabin wall curve is now correct on both sides and the outer proportions fit also

Thank you @allanyed. Those plans are just what i needed. Looking at them i noticed that the last bulkhead on the model is no wide enough. I will have to make new one in order to have correct inner wall curve.

As you can see this kit does not have interior for the cabines included so i will try to do it my self. I am trying to find the right blueprints of the ardent class 1764 for it and reference photos of simmilar ships. I guess the interior design is simmilar than the one on victory. 

I did found the blueprints of the quarterdeck but the upper gun deck is still the mystery to me. If ANYONE has any information, please feel free to jump in.

Hello everyone.

Yes, I am starting my second project. First one is in rigging stage and i love working with wood, so.... I bought this kit a while ago and i couldn't wait to unpack it and start modeling. My first ship of the line. I wanted to build this one 5 years ago but i knew i didn't have enough knowledge or practice so i had to start with something smaller like endeavour. The wait is over, lets get to the work. 

Since most of the wood work is done i decided to start with the 2nd project. Can you tell what is it?

Question. How do i add signature with current build below my posts?

Started rigging a bowsprit. So far it is going great. Also replaced metal lantern with the chuck's wooden assembly lantern.

All guns are now finished. It was a joy to assemble them.

Another update. I have been learning a lot about rigging and it is a slow and painful process. I have reworked the elm pumps, and the bases for swivel guns. Now it all looks more consistant. 

On 12/21/2020 at 1:42 AM, Chuck said:

You want to make another one!!!!   🤣  LOL

 

Truth be told....I almost chose Minerva instead.   But Winnie won out because of the wealth of primary source info.

 

By the way....the Minerva is also another 5th rate with just 3 lids aft and just one up at the bow.  Look closely at that forward lid.....note how the lid curves like the bow.   You need to pre-bend those little pieces before you make the lid.  Although not that much as I suspect that lid is curved even more due to age and warp.

 

Hi all. I have a question regarding wood on this model, last two pictures. What wood was used to get that nice warm yellow orange color. I am soon starting HMS agamemnon build from caldercraft but would like to have yellow parts not painted. Fell free to give me advice on what combination of wood to use. I would like to get nice details and sharp edges on smaller parts so i guess hardwood is the right choice. But what wood to use for planking hull that maches hardwood in color. Also what are the alternatives to hardwood. Thank you in advance

My first. Took me 4 hours to build it. It is aftermarket kit from syren.

Did a little bit of painting and continuing with shrouds

After few years of other hobbies and raising a child i lost my interest in modeling and now finally i am continuing my build. Here are few pictures of my progress. This is still my first ship so i am learning along the way.

Since it is my first model it is hard to tell how good it is. I see that other builders say it is all right. Wooden parts are of good quality. Depending how high you aim other parts can be good enough for you. If you want to improve your build than you will need aftermarket parts or make them yourself. Me personaly purchased new guns and ropes from syren ship model co. and few other parts. I still dont have enough tools to build them myself.

Thank you all

You are amazing