AnobiumPunctatum

Rather then continue work on my standard knees, grating, decking or the last of the three stairways to the hold, I decided it was time to tackle the thing I've been avoiding... the hawse holes.  The contract states they are 15" diameter, 15/64" at scale.  I first double checked my heights then drilled my pilot holes at 5/64".

Next, with a new sharp bit,  I drilled one inboard hawse hole very carefully and slowly with a backing board held on the inside.
Success!  That was easy.
Drilled the outboard hole and it happened. She split and flew off.
That was unexpected.

I setup the other side with clamps to help hold her together.
The outboard face of each of those holes have tear out chips in them!

So, I did the only thing left to do.
Glued the broken piece back on, clamped it up and left the room.

I won't be back working on her until Monday afternoon.
Good night world.
😉

Thanks for the information. I fully understand your motivation not to make the knees

Thanks for the information. I fully understand your motivation not to make the knees

It is looking really nice. One question: I miss the different knees, especially where the guns are situated. David has shown them in his drawings. Why do you have omitted them?

Thanks for the information. I fully understand your motivation not to make the knees

Thanks for the information. I fully understand your motivation not to make the knees

Thanks for the information. I fully understand your motivation not to make the knees

The knees wont be seen so they will be omitted.  Its easy enough for folks to add should they want to.  Thats a benefit of having Davids book while building the kit.  But it will really complicate and make adding all of those ledges take forever.  And all for something that will never be seen.  I think most folks will be relieved not to make them.
 
the contemporary model doesnt have them either.  My guess is for the very same reason.  
 
It also reduces the cost and time to manufacture the kit quite a bit. I did add them on the fcastle however because the ends of the knees will be slightly visible in the open area left unplanked.  So once the gun deck is planked…the casual viewer will actually assume you did add all of those knees for the entire model.  LOL
 
I will take a picture with the planking templates in position.  You will see what I am talking about pretty clearly. The same is true of all the ledges down the center line.  They will not be seen either.  The contemporary model also omits these..whats the point really.

I have reached another small milestone.  All of the below deck fittings and cabins are completed.  The gun deck is fully framed as well.   Next up I will start planking the inboard bulwarks.   That should make a huge difference.  
 
I hope to see many of you this weekend at the New London show.   It should be a very enjoyable weekend.   I am looking forward to it.
 







 
 
 
 
 
 
 
 
Chuck

I don't think so. In my opinion is the purpose of the drawing to show the differences between the standard frameing sheme (doulble frame followed by two single frames) and the sheme which was used for Kingfisher in the midship area. Interesting is also the triple frame midships.

Ah, the midship frames from Kingfisher. For the first. Ships of the class the frameing design, which was introduced with Cygnet is not correct.
I am busy with another Swan Class Fly. For this ship the Cygnet design is with some small adjustments possible.

Hi Kris,
 
I am really happy that you continue with your reconstruction of ths beautyful viking ship. I will follow as in the last years with great interest.

Ah, the midship frames from Kingfisher. For the first. Ships of the class the frameing design, which was introduced with Cygnet is not correct.
I am busy with another Swan Class Fly. For this ship the Cygnet design is with some small adjustments possible.

Hi All
Thanks for the likes.
Onto fitting the bulkheads
 
A quick jig was made to keep the spine vertical whilst the bulkheads were fitted.  Bulkheads kept square using Lego and clamps
 

 
Once all bulkheads were fitted I added spacers to keep everything square, this is simply achieved by taking measurements of the gaps between the same bulkheads on either side of the spine and taking the average, two pieces of stock are then cut to that length and glued in place between the bulkheads
 

 
The 3mm ply spine is still flimsy at this point so bracing pieces are required.  These are cut from the templates provided and 3mm ply is used.   I cut the bracing pieces roughly 5mm less wide than the templates so that the edge of the bracing pieces were clear of the bulkhead edges..
Following shows a couple of the bracing pieces cut and installed clear of the bulkhead edges
 


 
Gaps in the bulkheads are plugged with some pine and sanded flush
 

 
The frame is now rock solid and straight
 

 
 
Thanks for dropping by
 
Mark
 
 
 

Either I start again the same model (without mistakes) or the HMS Beaver itself. In both cases, we have no framing plan (my guess, see photo).

HMS Beaver => french design but english built. Slade , the best english naval architect, was very keen on french design.
 
 
Date : 1770

Hi Kris,
 
I am really happy that you continue with your reconstruction of ths beautyful viking ship. I will follow as in the last years with great interest.

This looks like a very promising start. I will follow with great interest.

This is looking really really good.

Putting it all back together:
Som images showing how the main units go back together after varnishing.
The main deck unit is placed inside the main hull unit and bolted together using a couple of brass screwdrives I made for the purpose (some of the bolts are quite fiddly to get at now all the seats are in place... The photo shows one of these screwdrivers accessing one of the difficult to get at bolts securing the base stringer.

 
I made a couple of "Link Seats" to connect the thranite seats at the aft end of the main deck unit to the ones fixed under the quarterdeck:

 
Then its a case of securing all 12 Canopy Units:

 
The assembly with all main units in place:

 
There are a number of other loose outfit fittings, like ladders to go in:

Complete assembly takes me about 1 hour at this stage. Hopefully I wont need to take it appart again for some time...

Current stage of varnishing complete. Please to say, none of my fears materialised:
1. The older work didnt look any different from the fresh stuff.
2. I managed to avoid blocking up the threads of all the captive nuts
3. The lightweight structure didnt distort.
Composite image of all the main components after sealing:

As an aside Ive got myself a new umbrella reflector kit to use for flash photography. It came with 2 umbrellas. These photos were its first outing, so still getting used to it... Im alreadyquite pleased with the "soft" white one which seems to give quite an even illumination (when I point it in the right direction!) with nice soft shadows...

Main hull unit and main deck unit now coated with 5 coats of Polyurethane Matt (thinned 25% with White spirit) and Ive started the first coat on the deck canopy units, ladders and other misc bits and pieces. It took me four full days to sand where I could (600 grit) before I started and 7 full days to apply the 5 coats to the 2 main units with a brush (sanding between coats with 1500 grit paper). Very fiddly work, there are a lot of brackets, stanchions etc that are quite difficult to brush around - even with the model fully dissasembled. I could probably have done it quicker with an airbrush, but dont have much experience using them so went for the brush in the end. I am quite pleased with the finish I achieved. Even the older wood (worked over 10 years ago) has some up nicely and is indestinguishable from the fresh wood (e.d. tabernacles and stowage racks). I was really relieved to find I could fit the deck unit back inside the hull unit (after varnishing) and bolt it down with out any difficulty. I had managed to keep the threads of the captive nuts free of varnish and there was very little distortion of the two units from varnish absorbtion (the hull had opened up about 2mm - which I was easily able to pull back with the bolts to the beam shelf on the deck unit. Hopefully the canopy sections (even lighter built - and so even more sensitive to distortion) will behave as well.
Photo below shows how the wood like looks now...

 

Forward tabernacle fitted complete with single steps to foredeck and braces...

 

Simpler at the fore end where the forward most seats on the upper level sit on the removable section. Luckily the bolts that I put in this area cleared them (well almost...). At one point I wasn't planning to fit seats so these bolts were placed without thinking about them...
 

Moving along I've finished the boxing joint and the first parts of the keel.
 
Next I'll add the false keel and the pieces on top of the keel for the rabbet strip.