-
Posts
2,949 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by Glenn-UK
-
I have made more progress, the hull has been painted but I'm leaving the covers on hull for the time being while I add some deck detail. I have added all the parts to the bow section and I'm currently adding some parts to the stern section. Pictures of the bow section added.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
The three main guns require a handrail, but you need to drill a 0.5mm diameter hole approx. 0.5 mm deep to secure the handrail posts. I soon found out that I was unable to drill these holes in the die case metal case. I solved this by adding a 0.5mm thick wooden top. This will not be noticed once the gun as been primed and painted. I have now completed adding the features to the port side of the hull, namely the load lines, portholes, hanger cranes and exhaust pipes. I opted to use some Amati potholes for the open hatches. I also used 1mm plastic strip for the load lines.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
Today I worked on installing the hanger deck and associated supports. The task turned out to be much simpler than I was expecting. I printed out a picture of the hanger support arrangement and positioned it under the deck and used that as a guide to add the various hanger deck support pieces. The hanger deck will require some additional filler / glue as can be seen below. The hanger deck grills have been dry fitted at this stage as then need to be removed and painted Iron Grey before they are glued in place.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
Thanks Mike It is an interesting build, difficult at times due to the poor quality of the materials and or the build instructions.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have continued on with steady progress. I have assembled 12 small machine guns, which was quite time consuming given how small the parts were and that I also had to manufacture 24 gun barrels, each 5mm long. I also fitted the bow and stern photo etched plates. Following on from that I added the rolling chocks, propellers and rudders to the hull assembly. Again there was quoite a bit of work involved with these tasks.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have continued to work on the main superstructure assembly. It takes quite a bit of work due to the poor quality of some of the die cast parts, requires plenty of filing and putty to correct. I have added primer to some parts to help highlight some of the defects The main bridge and funnel assemblies have not been glued as yet, as there is still some more bits to add.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
Thanks, still another day or two work required on hull before it's really smooth
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have spent quite a bit of time on sanding (and filling) the hull to get a nice smooth finish. It is still very much work in progress as I continue to apply more coats of primer and to then sand smooth. It is a task I prefer to do outdoors and the weather is not playing ball today (windy with a few drops of rain). To make the attached photo a bit more interesting I decided to add some of the superstructure parts, noting these have not been assembled or positioned correctly on the deck. They have just been added for a bit of fun, but I think they do add menace to the model. The two photo etched deck parts are also only positioned for effect. There will need to be painted prior to actual fitting.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I decided to deviate from the instructions, which requires each deck part to be planked separately and installed at a much later stage. I think it is better to fit all the deck panels first and to then fit the deck planks later on. The photo etched parts are only dry fitted at the moment as is the final deck part, as the hanger deck will require painting prior to the fitting. I found this method was much better for getting the hull profile to fit the sanding templates. Decks fitted.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
Having completed the hull planking I decided to dry fit the hull deck parts. The seemed to fit OK and will not require too much tweaking. I took the hull sanding profiles provided (a great kit idea) and spent a nice couple of hours in the sun this afternoon sanding and smoothing. The hull profile is now more or less in line with the all the different profiles templates. The hull requires a couple of minor tweaks. I think I will spray the hull with a primer to highlight any defects. This can then be filled as necessary and sanded smooth.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have now completed adding the strakes to the starboard side of Yamato's hull framework. It looks rough and uneven at the moment which is to be expected. I should be able to complete adding the remaining strakes to the port side in the next couple of days (or so). Once I have added all the strakes the hull can then be marked out and sanded (and filled) smooth, using the various templates provided to ensure the correct profile along the length is achieved. I think the sanding and filling process will take some time to get right. I have noted the problem strake toward the keel on the following picture, which I have now sorted out due to a bad glue joint.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have made more progress on the hull planking. I have now completed the stern area. I only have the final few top strakes to add. The fun and games then starts with the hull sanding. Templates have been provided to help check the shape of the hull during the sanding process.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
The replacement parts are supplied free of charge.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have continued to make good progress on both the superstructure and hull planking. The quality of some of the die cast parts is a concern, one part arrived badly warped, it has an approx. 3mm displacement. I could use the part but it would require a lot of filing and filling with epoxy resin. I have been in contact with the supplier and they have ordered a new part. Photo of warp part WIP Superstructures I am finding the detailed planking instructions very odd and goes against what I would normally do. I should be able to completed the hull planking in the next few days all being well. Planking progress photos
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have added a few more hull planks today. I thought I would share my method for doing this. The instruction manual requires 5 planks are fitted at a time. I started by measuring and cutting the 5 planks to the correct length. I then added a chamber to the top edge of the planks to ensure the edges line up when fitted to the hull. The next task was to make the pin holes and then to add the pins. I made a small hand made tool to make the holes. The first plank was then glued and pinned in place, ensuring it was correctly positioned on the hull frame. I then repeated this process for the 4 remaining planks, using clamps to close the gaps between the planks and where necessary using the pins to help secure the planks.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have started the hull planking, added 5 strakes each side. I have been following the instructions in the manual. To ensure the gaps are maintained at the bulkheads, scrap pieces were used as spacers.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
My IJN Yamato 1/250 scale model kit arrived 5 days ago. I have now completed the basic hull frame assembly. Once I have attached the bow assembly (also completed) to the hull frame assembly I can then start work on the hull planking. I am also making good progress on the bridge assembly.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
More work undertaken today on the bridge and hull Bridge Work I have added some more bridge parts. I made another small wooden jig (10mm one edge and 11mm the other edge) to support one piece as the epoxy resin sets. Hull Assembly I have now glued the majority of the hull bulkheads in place. I still have a slight issue with the warped keel support piece but it is almost straight. I'm just giving it one more clamping (after soaking in water).
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
I have sorted out the issue with the gun range finder and using epoxy resin, fitted both parts to the main gun assembly. I also fitted the flag signalling deck to the bridge assembly. This took a bit of time to get correctly positioned. I made a small wooden jig to aid the clamping of the deck as the epoxy resin cured. I tested fitted the range finders to the command post, they required a bit of filing before the could be located in the fixing holes. I added a some small wooden strips to help fix the warping issue with the base plate and also applied some wood glue and clamped the two edges. I also marked the position of the bulkheads and support frames to assist me to correctly pin the bulkhead. Finally I clamped the warped keel support, after I had soaked it in water. This seems to have sorted the problem.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
There is quite a bit of wood required for the hull assembly, especially when the hull and deck planking has been added which I think will balance the weight between the hull and the die cast super structures.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
Today I have started the build in earnest. First task was to dry fit the hull parts. Everything went together without any issues and the Yamato is going to be a big model. There are two parts which are warped however. One is one of the base plates which can be rectified when the bulkheads are glued and pinned in place. The other part is keel of stern part. I will probably have have to straighten this piece before it is fitted in place. I fixed the bridge misalignment issue. This turned out to be an easy task as I was able to file a little bit off the locating pins. I also looked at the first big gun. There are a couple of minor issues that needs to be addressed. The first one is the wooden based plate is a tad to big and a couple of the edges need to be trimmed. The second issue is one of the two range finders does not fit in the slot provided so will require a bit of filing to sort that out.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
-
It is not a cheap kit to buy, looking at other examples of this build, there are not too many build issues to contend with. There is a lot more detail to add to the bridge and the slight misalignment would not be noticeable when complete. However better to correct it, if possible, in my opinion.
- 64 replies
-
- yamato
- deagostini
-
(and 2 more)
Tagged with:
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.