goemon Posted March 9, 2021 Share #1 Posted March 9, 2021 (edited) Two months ago, I started making OccCre HMS Beagle. The Beagle is a famous ship used for exploration by Darwin, who discovered the theory of evolution. The kit is a production manual only, no drawings A detailed production video from the manufacturer is available on YouTuber. The material of the kit is rough in a nutshell, but the laser cut is accurate. As for the deck, I felt that the 60mm designation was too short, so I put up a 120mm long board. The sides of the board are painted black with a 6B pencil. I cut a 23g needle and attached a stamp with a nail mark. The inside of the blue work has been changed to Sapelli. There is no camber on the deck and it is flat, but it is difficult to change, so I will make it as it is. The door was made of wood. I bent it after getting it wet, but it broke. Falcata filler has been added to the bulkhead to make it easier to fix the wood with a thumbtack. The first outer panel has been pasted. I glued the keel before sticking the second tree. For the overlay, I pasted one gun gate and then two 2x5mm boards. I painted the wales black, stuck one Sapelli underneath, and then stuck it upwards from the bottom of the ship. The sheer rail 2x2mm was a little too thick. I painted it with natural milk paint. The white paint on the gun gate has been changed so that the lower part is about 5mm above the specified position. Edited March 9, 2021 by goemon The Gimps Chimp, Cathead, Pete D and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Gus M Posted March 9, 2021 Share #2 Posted March 9, 2021 the Beagle is one of projects in my mind to the future. The history of this awasome ship is fantastic. Really amazing. Your work is fantastic, I follow this thread and your advances with attentioin, thanks for sharing goemon 1 Quote Greetings Gus ------------------------------------------------------------------- Current build log: San Francisco Cross Section Link to comment Share on other sites More sharing options...
Cathead Posted March 9, 2021 Share #3 Posted March 9, 2021 Good work so far! goemon 1 Quote Eric Current builds: scratchbuilt Missouri River steamboat Peerless (1893); 1:1 scale timber-framed outdoor kitchen Nautical builds (kits): USS Cairo; NRG capstan project; NRG half-hull; Viking longship; US revenue cutter; 18th century longboat; Bounty launch Missouri River craft (scratchbuilt): 1853 Missouri River steamboat Arabia; 1865 steamboat Bertrand; Lewis & Clark barge; keelboat; 1876 steamboat Far West Link to comment Share on other sites More sharing options...
uncarina Posted March 9, 2021 Share #4 Posted March 9, 2021 Very impressive introduction! I really am enjoying your work. Will you be adding copper plating to the hull? Cheers, Tom goemon 1 Quote Link to comment Share on other sites More sharing options...
Kevin Posted March 9, 2021 Share #5 Posted March 9, 2021 thats very nice indeed goemon 1 Quote Its all part of Kev's journey, bit like going to the dark side, but with the lights on All the best Kevin SAY NO TO PIRACY. SUPPORT ORIGINAL IDEAS AND MANUFACTURERS. KEEP IT REAL! ------------------------------------------------------------------------------------------------------------------------------------------------------ On the build table HMS Indefatigable 1794 by Kevin - Vanguard Models - 1:64 - Feb 2023 HMHS Britannic by Kevin SD 14 - Marcle Models - 1/70 - March 2022 - Bluebell - Flower Class - Revel - 1/72 U552 German U Boat - Trumpeter - 1/48 Amerigo Vespucci 1/84 - Panart- HMS Enterprise -CAF - 1/48 Finished St-Nectan-Mountfleet-models-steam-trawler-1/32 - Completed June 2020 HMS Victory - Caldercraft/Jotika - 1/72 - Finished Dorade renamed Dora by Kevin - Amati - 1/20 - Completed March 2021 Stage Coach 1848 - Artesania Latina - 1/10 -Finished Lady Eleanor by Kevin - FINISHED - Vanguard Models - 1/64 - Fifie fishing boat Link to comment Share on other sites More sharing options...
BranPie Posted March 9, 2021 Share #6 Posted March 9, 2021 (edited) Following! There's a lot of these builds ongoing, but since I'm just about sure I'll be building one of these in the future I'm following every one of them. You have gotten of to a great start. 👌 Edited March 10, 2021 by BranPie goemon 1 Quote Cheers, Pieter Current build: Polaris (OcCre, 1:50) Link to comment Share on other sites More sharing options...
Pete D Posted March 10, 2021 Share #7 Posted March 10, 2021 12 hours ago, goemon said: Two months ago, I started making OccCre HMS Beagle. The Beagle is a famous ship used for exploration by Darwin, who discovered the theory of evolution. The kit is a production manual only, no drawings A detailed production video from the manufacturer is available on YouTuber. The material of the kit is rough in a nutshell, but the laser cut is accurate. As for the deck, I felt that the 60mm designation was too short, so I put up a 120mm long board. The sides of the board are painted black with a 6B pencil. I cut a 23g needle and attached a stamp with a nail mark. The inside of the blue work has been changed to Sapelli. There is no camber on the deck and it is flat, but it is difficult to change, so I will make it as it is. The door was made of wood. I bent it after getting it wet, but it broke. Falcata filler has been added to the bulkhead to make it easier to fix the wood with a thumbtack. The first outer panel has been pasted. I glued the keel before sticking the second tree. For the overlay, I pasted one gun gate and then two 2x5mm boards. I painted the wales black, stuck one Sapelli underneath, and then stuck it upwards from the bottom of the ship. The sheer rail 2x2mm was a little too thick. I painted it with natural milk paint. The white paint on the gun gate has been changed so that the lower part is about 5mm above the specified position. Great work goemon 1 Quote Link to comment Share on other sites More sharing options...
goemon Posted March 10, 2021 Author Share #8 Posted March 10, 2021 Thanks Gixli,Cathead,Uncarina,Kevin,Brainpie and Pete. 20 hours ago, uncarina said: Will you be adding copper plating to the hull? I don't really like the copper plate on the bottom of the ship. If I were to scratch build, I would stick a copper plate, but I didn't intend to stick this kit from the beginning. uncarina 1 Quote Link to comment Share on other sites More sharing options...
goemon Posted March 10, 2021 Author Share #9 Posted March 10, 2021 This is an image of the current Beagle. I also put Sapelli material on the keel part. The hinge part of the gun gate metal fittings is not reproduced. The bottom of the ship is coated with flaxseed oil, which is easier to use than varnish. The handrail has been cut from 7mm width to 5-6mm width. The diamond-shaped hollow of the part where the hammock is inserted cannot be reproduced. Since there is an exhibition, we need to complete HMS FLY by the end of June, so we may not be able to make Beagle for a while. GrandpaPhil, Fernando E, uncarina and 3 others 6 Quote Link to comment Share on other sites More sharing options...
uncarina Posted March 11, 2021 Share #10 Posted March 11, 2021 I’m very impressed with your work so far! Cheers, Tom Quote Link to comment Share on other sites More sharing options...
Dart Posted March 11, 2021 Share #11 Posted March 11, 2021 I also paused a little. GrandpaPhil and Valeriy V 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.