Jump to content

Lowell Grand Banks Dory by Reece - FINISHED - Model Shipways - 1:24


Recommended Posts

Hello Model Ship World members. I’m Reece and I'm a new boat modeler.

 

I decided to start my start my journey with the Model Shipways Shipwright Series. The first build is the Lowell Grand Banks Dory. I don’t have all the pictures from this build but I have a fair amount and wanted to post this for those that may be looking for references in the future.

 

I thought this was a great introduction to ship modelling and thoroughly enjoyed my time spent on the project. I definitely learned a thing or two and look forward to applying those to my next build in the series.

 

Here are some of the steps I struggled with on this build and how I corrected them:

  1. I had trouble aligning the bottom/stem/transom assembly with the frames and building board. This is something I should have spent much more time on because it ultimately affected the outcome of the planking. I should have spent some more time getting the stem and transom holders securely placed. Some slop here caused the transom to not be exactly perpendicular to base of the building board and resulted in the planks being slight asymmetric when viewed from the bow. I ended up just sanding this as best I could and the planks are slightly uneven. Lesson learned for next time for sure.
  2. My seat risers were slightly off and had to be removed and reattached as it made the thwarts out of level.
  3. I tried to thread the beckets without applying CA to the tips first. This caused me to waste an entire section as it unraveled before my eyes. I was able to salvage this step with the remaining pieces by dividing the remaining rope in half and giving myself extra material to work with beyond the recommended 4" section. I think in the end the pieces ended being about 5 1/2" each. I had just enough and was able to trim the excess to match the pictures in the instructions.
  4. The oars. I was too heavy handed when sanding the oars and completely lost one when it snapped in my hands. Yikes. Luckily the kit includes an extra laser cut piece probably for this very reason. I ended up snapping the hand holds on several of the oars as well and had to glue some little pieces of balsa I had left over to make them look somewhat like the pictures. Not my finest moment but I’ve definitely learned a lesson here that I can use on future models. I’m not totally satisfied with the shape and look of the oars. I might try to revisit in the future if I’m looking for something to do.

 

Other Notes:

  1. I found the section on the thole pins was slightly different.  In the instructions it mentions using a 3/64" dowel and cutting the pins to length.  I spent some time looking for this until I realized that a dowel was actually not provided but was replaced in the kit by a strip of 3/64" balsa.  I ended up cutting this in half and shaping it on a drill press.  I inserted the balsa half way into the chuck, set the speed on the lowest I had available (approx. 500 rpm), and then proceeded to very lightly apply sandpaper to the strip as it spun.  I flipped the balsa piece in the chuck and repeated.  It made short work of creating the dowel.

 

Overall I had a great time with this kit and would definitely recommend anyone who’s curious about building it to give it a go. Its a great model to learn some basic ship modelling skills on.

 

processed-img_1135.jpeg.c0026525bbd4dd44c2dcb39e3d0f5a20.jpeg

The completed Lowell Grand Banks Dory.

 

processed-img_0419.jpeg.527515f1c0ecd06c2d153c088be7e7e0.jpeg

Attaching the sheer plank.

 

processed-img_0423.jpeg.12e5f4207a325e8230c97dd3175e2c69.jpeg

The Dory right side up and about to clean the frame tops.

 

 

processed-img_0458.jpeg.f746429b25ff8c89356b0f52adc9f7e4.jpeg

Gluing on the starboard gunwale.

 

processed-img_1115.jpeg.ed22083313e9ed212a07cf441523b05b.jpeg

Attaching the cap rail after painting the model using the recommend Hull Yellow Occre and Bulwarks Dark Green.

 

processed-img_1120.jpeg.42ea1765d753f5f26b1d2e864ed0b15b.jpeg

Close up of the bow after rebuilding the stem top so that it was aligned better with the cap rails.  This was a result of poor original alignment of the bottom/stem/and building board before planking.

 

processed-img_1123.jpeg.f55d96e87fee490fd8126c8f0943c183.jpeg

Using the handle of a model knife to force the becket into place after applying the watered down PVA glue.

 

processed-img_1124.jpeg.d1fd7cee6a261816cae841e134b6ea47.jpeg

Cutting and installing the thole pins.

 

processed-img_1130.jpeg.dbc99755965594e44c9f57e593553ac0.jpeg

Attempting to fix the oar handles.

 

processed-img_1136.jpeg.4b8785146b6fd4b6f6b248a193074007.jpeg

Another shot of the completed Lowell Grand Banks Dory.

 

Edited by Reece
Link to comment
Share on other sites

Well done, Reece. You've learned a lot out of fixing and re-doing things. This will stand you in good stead for your next model. A very respectable first model indeed!

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Excellent job on your first build.  You have learned skills that will help you on future builds.

Ryland

 

Member - Hampton Roads Ship Model Society

            - Ship Model Society of New Jersey

               - Nautical Research Guild

       

 

Current Build - Armed Virginia Sloop, 18th Century Longboat

Completed Build - Medway Longboat

Link to comment
Share on other sites

Super congrats Reece.   Looks like you got a great start with the dory model.  One little trick to make the handles round, if not tapered, is to drill a hole in a piece of brass, aluminum or steel,  cut a couple slots and then chuck it in drill or drill press and run down the handle area.  Picture below when I used it to round the axles on gun carriages.

Allan

953325348_Axletreesandcutter.jpg.a9b35378cf7a28b7c8128bae013b4525.jpg

 

 

 

 

PLEASE take 30 SECONDS and sign up for the epic Nelson/Trafalgar project if you would like to see it made into a TV series.   Click on http://trafalgar.tv   There is no cost other than the 30 seconds of your time.  THANK YOU

 

Link to comment
Share on other sites

  • 2 years later...
Posted (edited)
On 1/23/2022 at 12:25 PM, Reece said:

tried to thread the beckets without applying CA to the tips first

I have mine in the mail and am browsing builds to learn while I wait. What is CA in this context? some sort of adhesive?

 

Great job on your first build btw!

Edited by MBerg

On the slip:

Norwegian sailing pram

 

On the drafting table:

OcCre Polaris

Muscongus Bay lobster smack

 

Completed:

Lowell Grand Banks Dory

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...