Armed Launch by Sluicemaster - Panart - 1:16

CiscoH · October 1, 2022

looks really good! the stain takes it up a notch too

nice job

Mike Collier · October 1, 2022

Yes, it’s really looking great! Where did you get the long black clamps?

Sluicemaster · October 4, 2022

Hello HardeeHarHar, Mike Collier, Bruce D, CiscoH, Prowler901, and Paul Le Wol;

Thank you, gentlemen, for your likes! They are inspiring when I hit difficult instances doing this model.

Cisco - I tested 14 different stains before settling on special walnut. Boy, I'm set for a stain-fest now! I'm following your AVS build, and must apologize for not leaving comments, sooo - Good Job! I look forward to doing mine if I ever finish the launch, which I hope is in 2023.

Mike - I get the clamps at Menard's. For a while they carried Wolf clamps, the switched to Bessey brand. The are pretty much identical. It'd be really cool if someone made even longer clamps with the same small silhouette.

Sluicemaster · October 4, 2022

Thank you ccoyle for your Like. I appreciate and am thankful for all comments.

Sluicemaster · November 1, 2022

I’ve completed what I wanted to before my back surgery. All of the steps had challenges of their own, but I completed all of them with satisfaction. The biggest and most satisfying task was to finally remove the build form. I was happy to see that no glue seeped through the cherry wood planks. I used the kit supplied wood for planking below the deck surface. Lines of the strange planking diagram supplied on the plans is visible, but I don't think it will be too noticable as the interior is finished off. I did not use the kit offered method on layers two and three.

What the instructions called the rubbing boards (The best name I could find was bilge keels) were interesting, though a bit frustrating, project. Positioning them according the plans was sketchy, and aligning them with the keel proved the value of dividers. I tried using a thin stick taped to the hull as an alignment guide for gluing, but the tape pulled up some of the stain. Touching up was not a problem. I then switched to good ol’ rubber bands. I’m not totally pleased with their outcome, but since I used super glue I had to accept it. They are cherry wood brushed with India Ink.

Attaching the rubbing boards on the side of the hull once again showed that one can never have too many clamps. I first used clamps to secure purposely cut wood at a specific distance from the top edge of the hull. Since glue was applied the full length of the board, I pre-positioned clamps to secure the board as I laid it down. The boards are cherry wood brushed with India Ink. Two strips were butt-spliced in order to make a full length piece. The blue paint is dark blue acrylic model paint from Hobby Lobby.

The hull has been quite a project, and I’m really happy to move on to the “innards” of the launch. Every time I look at how badly the plywood keel took stain, I want to scream. I've pondered applying a thin veneer and staining it, but I'll have to sleep on that a day or twenty!?

ajromano · November 25, 2022

I have a bad case of clamp envy going after viewing this build!

Sluicemaster · November 25, 2022

Hello ajromano;

A coming post picture will be clamp overload!🥴 Stay tuned.

Sluicemaster · November 27, 2022

I thought I'd open this post with some photos of my "shipyard." I have one wall of what my wife and I call our "cave", while she has the other three for her crafts. If my wall looks full, you should see her three and the closet! Since I don't have room to spead out the plans, I had copies made so that I could cut sections and hang them on the door. At this point I found out that the plan drawings are not truly to scale as they profess.

I was so glad to be done with hull planking, and so bummed at how the keel looked, that I almost forgot that the plans called for it to be planked. Since the plans call for the bottom of the hull to be painted, I planked the keel different than what the plans showed.

Planking the forward and aft decks went well, but it became apparent that the bow deck is too high for proper mounting of the cannon carriage. I'm guessing that when I get to that point I'll have to raise it on the bench.

The main deck support does not conform to the inner planking so I had to add filler strips. I decided to build the deck outside of the ship so it would be easier to work on. I established where the outer edge planks should sit so that when installed, the ribs would properly meet it. When I stained the outer planks after bending with heat, I found that that they took stain differently than planks that had not been exposed to heat. They are much darker. They and the cross planks are Alaskan Cedar. The fill planking is cherry wood. All are stained with MinWax Honey stain.

Planking the deck is a delight since I don't have to do any bending and shaping. Soon it became apparent that I did not order enough 2mm x 8mm cherry planks. I couldn't order any more right now because Joe at Modeler's Sawmill is healing from hand surgery. Sooooo - I decided to glue together extra 1mm x 6mm and 1mm x 7mm planks topgether so to get 2mm thick planks. The plans call for 8mm width but these thinner planks will make no real difference. This proved my favorite mantra that one can never have too many clamps.

At this point, planking is going well. I've started making the grating frames, and will post next when the deck is done. Thank you for looking at my project.

Sluicemaster · January 16, 2023

The kit did not supply enough grating strips to construct all of the grates, so I installed planking in two of the forward grate positions. I tried altering and gluing the small left over grate pieces together, but to no avail. The strips are stained with Minwax Honey stain, as well as the frames which are Alaskan cedar. The cedar does not take satin well ofter being formed with a hot iron.

For some reason the stained wood looks washed out in this picture.

After the decks were installed, there was a two millimeter gap between the framing strips and the hull, just enough room for the ribs to fit snugly.

All of the ribs are Alaskan cedar and were individually bent and marked, then stained with Minwax Honey stain. I made small angles and a T-square to assure perpindicularity. At some point my carefully planned rib spacing went awry, and there is some inconsistency in a few places. This may slightly affect the spacing of one seat, but I hope that will not be too noticeable when the model is complete.

My trusty supervisor cat keeps an eye on my progress much of the time. Since there's not much sun in the winter, she takes soaks up rays from the lamp.

I had a lumbar laminectomy in October, and still have an issue with lumbar foraminal narrowing which is sometimes aggravated by sitting for long periods. So I built a platform hoping I could work while standing. It did not work out, so I just take more frequent breaks from sitting. Supervisor cat thought it was pretty cool. Probably more surgery will be needed to fix my "issue." Ahhhh - the joys of old age!?

To position the longitudinal strips to the ribs, I made two small height gauges to position small blocks of wood that set the top position of the rail correctly.

The nails supplied with the kit were too long, so I replaced them with some from MicroMark.

I'm pleased overall with the progress. I took a break from rib installation to work on the cannon assembly, and am looking forward to installing the benches and cannon. The wood called out for the carronades was too small in cross section, so I've ordered new wood from Joe at Modelers Sawmill. I also ordered an extra piece of wood for the aft benches in case I make an error while using the supplied walnut.

Thanks for looking at my project. Happy new year to you all.

CiscoH · January 17, 2023

looks great!
i too have back issues and resultantly do all my work standing. a great plan until my knees go.

Sluicemaster · May 13, 2023

Holy smokes! It’s sure been a long time since I did a post. I should have made more progress in the past four months than I have, but I’m happy with the progress achieved. I had to spend considerable time “ashore” taking care of the homestead, and take a wonderful vacation to Virginia Beach with my wife. Her lifelong dream of seeing the sun rise from the ocean was fulfilled with great sunrises. I got some serious beach metal detecting done, and managed to add one more silver ring to my findings.

While on vacation we went to the Mariner’s Museum in Newport News. I last visited it forty years ago, and was stunned at how it had grown, especially to accommodate the preservation of the Monitor, and provide viewing of its restoration. I’m hoping to take another trip to Virginia Beach, and would plan to spend an entire day at the Museum. The Crabtree collection is what sparked my interest in building ship models.

Now, on to the armed launch. I haven’t been taking as many pictures as I should but hope the ones presented here will suffice.

I replaced all of the wood in the kit, so the benches are made of cherry rather than beech. They are stained with MinWax Special Walnut.

As I expected I would, I had issues making the aft benches, so the replacement walnut that I ordered ahead from Modeler’s Sawmill paid off, and I finally made good benches.

It’s not real apparent from the pictures, but the top profile of the hull was not consistent from side to side and fore and aft. I’m sure its due to a lot of little stresses that built up in the three layers of planking. The cherry was a real bit of work to properly form and bend. Because of this I opted to make the stern side cap rails straight.

The kit instructions called out a rather awkward way to make the forward cap rails, so I made them in one piece from a pear wood plank 3mm thick. To do it I made a tracing of the contour for each side, then added the appropriate thickness to each side of the line. I’m really pleased how they turned out.

Only the stern cap rails are currently glued in place. All rails will be colored with India Ink, but first I need to mask off future glue sites.

Supervisor cat likes to keep a close eye on me, and sometimes just plops down wherever she wants to.

Thanks for viewing my post and work. The next post will be in a timely manner.

ccoyle · May 13, 2023

You have a handsome helper!

rcmdrvr · May 13, 2023

You hull is beautiful and the planking is impressive. I have to hide my planking behind paint.

Sluicemaster · May 13, 2023

Hello ccoye and rcmdrvr;

Thank you both for your kind words.

Planking this model was quite the task. It took almost a year, with plenty of time outs! When I decided not to use the supplied wood, I chose cherry because that's what was available at Modeler's Sawmill. After doing stain and clear coat tests, I felt that it would be a travesty to cover such nice wood. As I am still a fairly new modeller, there are plenty of awkward spots on the planking and model. As the hull becomes more populated, those issues become kind of hidden.

I notice that Model Expo currently has this model on sale. I hope my reference to ME doesn't offend too many readers. I have been a customer for almost thirty years, and will not abandon them because of a one bad mistake The one offered is by Mantua, while mine was made by PanArt in the mid-1990's. I'm almost tempted to buy it so that I could plank it with the knowlege I've gained. I won't though, because I have the Armed Virginia Sloop, New England Whaleboat, and John Smith's Carrack on the shelf.

Supervisor Cat, Muffin, is great! She has never once attempted to paw or play with my project. When supervising, she generally sits off to the starboard, and keeps an ever non-blinking gaze on construction.

Sluicemaster · May 14, 2023

Oops! I have John Smith's Shallop, not Carrack, on the shelf.

whitejamest · May 16, 2023

On 5/13/2023 at 6:28 PM, Sluicemaster said:

Supervisor Cat, Muffin, is great! She has never once attempted to paw or play with my project.

I would pay Muffin a great deal if she could teach my own supervisor a similar attitude.

The boat is looking beautiful. You do very neat work.

Sluicemaster · September 2, 2023

As I worked to finish the tackle on the cannon carriage, it suddenly hit me that I never posted about completion of the rails. They went well, and I’m happy that the India Ink worked so well. I applied two coats topped with a very light, almost a dry brushing, of matte polyacrylic.

The kit supplied a wood torroid that was to be cut into pieces to do the curved section between the stern and main deck rails. It was a perfect “unfit”, so I laminated sections of cherry strips together, and turned out new ones on my DB-250 lathe.

Thank you for viewing my project.