Jack12477

Guy Fawkes Day, British observance, celebrated on November 5, commemorating the failure of the Gunpowder Plot of 1605

I have Richard's honing guide. Bought it several years ago thru Garrett Wade catalog. Don't know know if they still carry it. I have used it on some of my other chisels. Thanks for the link.

👍👍👍👍

My table and accessories have arrived. I was asked in PMs from a couple of members to do a review once I received the order from Lee Valley. Haven't had much time to really test it out but my first impressions follow: The table is impressive and well made. It's laminated Birch plywood, 12 plys, 5/8 inch thick, 4 rubber feet measuring 5/8 inch high are attache d with screws to the underside, overall table is 8 inches wide by 11 inch long, holes are 7/16 inch diameter spaced 1-1/2 inch apart in each x-y direction, rows indent approximately 1 inch from each edge. I checked the mini vice and there is not enough clearance under the table to install it. You would have to remove the rubber feet and make new legs. Footnote: After re-reading the instructions for the mini vice it appears to require a bench top thickness of 1-1/4 inches. This table top is only 5/8 inches thick, so some modifications would be needed. The accessories are tiny but well made as would be expected of Lee Valley. I would recommend storing them is some type of parts drawer or box so they don't get lost on the workbench. The packages. Unpacked Some test setups Using the miniature block plane Using the miniature Plow Plane Level up Jack Plane Using my ceramic sharpening stone and the miniature honing guide to sharpen one of the miniature chisels I didn't do a lot of setup work or try to do any serious work, just some quick tests with a couple of planes. It sat pretty flat on my work bench and didn't move around when I was planing but if I was doing something more strenuous it might need clamping to the bench to keep it from sliding around. The rubber feet could be removed and longer legs attached to give it more height of the work bench/table. All in all I think it is a worthwhile investment, especially for those with a small workshop and workbench. I didn't order the hold down accessory because I didn't think I would need it but I may reconsider that decision. As I use it more I will post updates and/or suggestions.

Chuck, I've found these videos on sharpening and stropping helpful. Once you have the chisel sharpened, then stropping before each use, and during use, should keep it sharp. You should not have to,put it to a stone everytime. I use this technique for my woodcarving knives. Also use a good stropping compound, usually comes as wax stick, green is finest grit. Sharpening Stropping

Good choice! My table arrived last night, rest of backorder items shipped today

Well the "in stock" portion of my order arrived last night around dinner time. When the remainder of the order arrives, I will post photos.

Here's Thor dismounted from the Railroad carriage with its loader in 1:35 scale. Yea I went down the rabbit hole with that mortar. 9n

Denis, you should add Thor to the collection. I built this model ages ago.

Nice !

Wow! Impressive Denis !

Kevin, follow the links in Post #10, they are 7/16 diameter

No, that's the full size one. I want the miniature table top bench as shown below. It's perfect size for small stuff and it accepts the mini vice. m

Yea making a video of making a toothpick is tad silly. 😬 I wish they had used a more serious subject because the mini tools are excellent tools, perfect for tapering ships planking, square an edge, or even thinning a plank. And I have used them on 1:1 stuff where the full size tools are too big for the task. That depends on what you are using it for. I have a full size wood vice (two in fact) on my Sjoberg Hobby Bench which I use a lot. And I have used vices similar to the one posted. But when it comes to clamping the size wood we use for our model ships, I find both woefully inadequate or plain over kill. And I have tried several of the keel clamps for holding the model which I quickly discarded as more of a PITA than useful. I have a decent selection of Veritas and Lie Nielson planes for 1:1 work. As for metal bending, the "metal" I need to bend is PE brass and "the Bug" from The Small Shop does an excellent job for me.

I wish they would publish the plans for the table in this Video

Yes! It comes with instructions and diagrams on how to attach it. Mine is still in the box waiting for a suitable small bench. Been looking at various mini tables on YouTube for ideas.

I have that mini vice ! 😉

Veritas miniature work surface Veritas miniature surface dog set Veritas miniature wonder dog Veritas miniature planing stop set Veritas miniature hold down Veritas miniature work surface accessories set All are individually available for purchase. The wonder dog and planing stops are backorder, due in Nov 1st according website. Everything else is in stock

What's out of stock ? I just looked and the table worktop and surface dogs are available online. The plane stop and other dog are backorder.

Just got confirmation from Lee Valley that my order for the board and one set of dogs has shipped, the other set of dogs are backorder and will ship soon. Admiral doesn't know it yet but she's giving it to me for Christmas 😊😇

While browsing the Lee Valley website I came across their online 2021 Christmas Catalog. On page 36 they show this cool miniature worktop with 1/3 scale miniature hold down clamps. This is a nice addition to their 1/3 scale miniature Veritas tools.

Looks good Edward

Or place a Kleenex tissue over the flash if you can. Try just 1 thickness of tissue to start, add more if needed.

He's going to need major therapy for that leg caught in that bear trap ! 😳 Looks good Edward !

Welcome Len, you may find this link useful HRMM. I live a short distance from Hudson River