hollowneck

Excuse the newbie ignorance but I assume that is another forum?
Again as a newbie to the hobby I can't imagine (other than insecurity and jealousy( what folk can say negatively about your work. Having looked at a lot of kits before moving on from my first (admittedly online) the only kits I really wanted to try were yours and Vanguards. On all of the build logs here it comes across so strongly how high the quality of both your kits are to give any stage of modeller the very best chance of making something stunning. Yes they are expensive but you get what you pay for in most areas and this is definitely one.
Good luck to you!
 

Yes, another forum but seriously most already know what they are like...thats why I wanted to post publicly for everyone not to take the bait.   Its just not worth it.    Just stay clear of the whole bunch.
 
Chuck

Thanks Chris, Chuck, mugje, really appreciated. 
 
Fitting out of Adder’s hull nearing completion. 

I decided to risk blotches and apply Danish oil to the outer bulwarks and it worked! The engraved pear looks amazing with Danish oil. 
I’ve done a somewhat amateurish job of fitting breech ropes to the cannons and carronades. 
The cannonballs were added using ultra matt poly varnish to hold them and take some of the shine off them. 
Fitting the parts is pretty straightforward. The fiddliest parts are the rope for the wheel and also for the drop keels. I have taken the drop keels off again whilst I manhandle the hull and fit deadeyes and chainplates. 
 
I’m leaving the anchors off until rigging is complete. I’m not sure when best to fit the hammock cranes and the cord between them as they’ll likely be in the way to for tying off rigging, then again I’ll need access to fit them which may be hard post-rigging.
 
Still to add the deadeyes, chainplates and drop keels. 
 
Thanks for looking! 
 
 

Well, the file's been done now for that figure, so can no longer change it. I will ask for a seated officer next.
 
What a morning, from 9am until just now I have been cleaning the laser machine after re stocking Indy and other laser cut parts. Not an enviable job..

That's better
 

Touché, Chris. A cut above.

Touché, Chris. A cut above.

The sword will be replaced with a 1795 Naval Pattern

The detail looks amazing Chris, but I'm intrigued by the style of the sword.
 
It does not  resemble any Naval sword I recall seeing, was it perhaps a specific sword gifted to Nelson?
It rather looks like the sword on the Nelson statue atop his column.
 
The Nelson Companion edited by Colin White has a photo of the only sword that is known to have been owned by Nelson, and it is of the traditional type.
 
For the purposes of displaying the figure on a model I think it would be safer to include a Naval pattern sword.
 
Just a thought.
 
B.E.

I have commisioned a second figure of Nelson using a new carver with more accurate facial features:
 
These are a work in progress with a little more tweaking required. The render showing Nelson on the plinth was the first. I asked, based on previous feedback, to have dowels on the bottom of the feet and holes to take the dowels in the plinth, if people want to display the figure either on the plinth, or on the deck directly.

Here is an unboxing review of Sherbourne, bt the Midwest Model Shops in the US:
 
(Not much else to report on, just been producing/re stocking Indy laser cut sheets, which has taken an absolute age to do...)

Here you can see the ply pattern clamped and glued in place. No pins were used at all in fixing these. They were first clamped in place and then brush glued. Note there are no kinks in the lower edges at all, all fits nicely. The second pic shows were I am up to, checking the very first iteration of the outer bulwark skin and main wale, just clamped loosly in place to check general fit. The final ones will have engraved detail. Next job is to first plank the hull, which I shall start next week.

Yes, most will not be seen, as I have to take into account the depth of the carronade carriages and the various openings down the centre of the deck. When I started this, my main thought was that I want to include a ships stove, and it kind of progressed from there.
 
However, as some build logs of Sphinx and Indy has shown, the modeller can choose how much of the upper deck is planked, and this one will be easier due to the sub deck being much less prominent, and the beams being flush with the upper surface of the ply deck.
 
I always think back to the excellent Tamiya kits I have, where they have details that are almost, sometimes completely covered up once fully built. 

Harpy also has 17 bulkheads with lots of bracing, so very structurally sound..
 
Yesterday I clamped and then glued the final iteration of the gun port patterns - as usual for this sort of kit, no gunports or oar ports need to be marked and cut out, these will be already done.
 

If you go to the Royal Museums Greenwich site, there are many open boat plans showing davits and windlasses. An example:
 

The windlass and stern davit was used for various tasks, one of thich was to help work the anchors with their parent ship, helping lifting the crown so that the anchor could free itself, and the the ships capstan did the work of raising it. The windlass was used to coil the buoy rope.

I have the second in my new line up of alternative printed resin boats almost ready. This is a 24 and 26 foot launch, complete with windlass and davit.

It is time to start rigging the mast.  Some lines are served with an additional layer of line wrapped around them to protect them wherever they would be at risk of damage from rubbing.  On this model, the pendant of tackles, the foremost shroud, the other shrouds above the catharpins and the jeer block strop are served.  Because this is a cross-section, the main and back stays will not be installed but they would also be served.  Standing rigging is protected from water damage with a tar-like compound.  This resulted in a dark brown appearance to the lines.  The running rigging was not protected and so was a natural hemp color.  On this model, the burton pendants and shrouds are standing rigging;  everything else is running rigging
 
Rope sizes are calculated from the diameter of the mast.  The kit contains a table with the dimensions for the various ropes, based on the diameter of the mast.  To measure the diameter of the line, I wrap it around a dowel twenty times, measure the width of the wrapping and divide by twenty.  This is much more accurate than  trying to measure an individual line. The first rope to go over the masthead is the pendant of tackles.  On the topmast, this line is referred to as the burton pendant.  This rope is completely served, and has a thimble on one end.  The other end is spliced to its opposite, resulting in the rope in the diagram below.  Where the red and blue lines meet are splices.  The pendants extend to approximately two feet below the hounds.  They were used with a tackle to raise and lower heavy weights.

To properly rig a model there is no substitute for the appearance of a served line.  I use 6-0 fly tying thread, which can be purchased at a sporting goods store or online.  I start by running thread, from left to right in this case, into the depression between the rope strands (worming), smoothing its surface (the yellow areas seen in the drawing below.  Then I serve the rope from right to left. 

I find it easier to serve short segments of rope, such as this, on the same piece of rope and then cut them apart.  I served the rope, leaving approximately six inches of serving thread for the splices (red circles).

Then I made a diagonal cut, following the lay of the rope ¼” away from the end of the serving.  The unserved line was held against the other line where the splice would go and I wrapped the two lines with the left-over serving thread “splicing” them together.  I continued the wrapping a few more twists to smooth out the transition and tied it off.  A tiny bit of dilute glue held everything together. The pendant was put over the mast head and onto the bolsters.  It was marked on each leg, two feet below the hounds and removed from the mast.  I used blackened 1/16” ID brass tubing for my thimbles.  The mark was placed on the side of the thimble and the pendant was wrapped around it.  For simplicity I used a simple seizing to secure the thimble and put it back on the mast.

 
 
 
 

Everything depended on the size and type of ship.  This little ship only had a lower mast and topmast.

Most kits come with deadeyes and partially completed chains.  Usually, the upper link (the link that goes around the deadeye) is pre-formed, with the bottom cut for insertion of the deadeye.  Wire is provided for the builder to form the other two links but the entire assembly has very little strength and the cut ends of wire are ugly.  The only way to make this assembly stronger and better looking is to solder the links closed.  I prefer silver soldering, even though regular soldering will give sufficient strength.  The benefit of silver soldering is that the metal is fused together rather than connected by a dissimilar metal, tin.  This makes it easier to bend the part without worrying about the solder joint breaking.  The downside is that there is a learning curve and the tools are more expensive.  Silver solder also blackens well.  There are also low melting point silver bearing solders (Tix) which can be blackened. 
 
The measurements for all the parts of a British warship were determined by the Admiralty.  There are reference books that contain this information such as Steel’s Tables.  An easily read version of the tables is sold in the NRG store.  The main mast diameter is given on the plans as 18”.  Using the information from the tables, I determined that the main stay is 9” and the shrouds are 5.5”.   Lines are measured by their circumference. The diameter of the deadeye is 1.5 times the size of the shroud or stay it is attached to, in this case 8 ¼”.  A spreadsheet comes in handy in determining all the measurements.
Let me start by saying that my metal work has a bit to be desired.  The chains are made from 1 ¼” wire, which is 22 gauge.  I temper the wire by drawing it through a gas flame until it glows red.  This makes the wire more malleable and removes any factory applied coating.
 
The deadeye chain is the same length for all the deadeyes.  Make one and use it as a template for the others.  I wrapped wire around the deadeye, leaving long tails, and inserted this into the slot in the channel.  The tails were cut long enough to be able form the loop below the channel.  I removed the deadeye and applied a finish. 

The lower links are all the same length.  From the plans I knew that the toe of the lower link is bolted 5” below the top of the wale and that its overall length was 9”.  Two T-pins were inserted into the soldering board and the wire was wrapped around them, with the cut ends on the side.  The middle link is different for every shroud because each is at a different angle to the mast as seen in the two pictures below.  The link becomes longer with greater angulation of the shroud.  You can see the difference in the shroud angles and how this would affect the length of the middle link.


To determine the angle of the chains, I put masking tape on the hull above and below the channel.  A loop of rope was placed over the mast head and inserted through a slot in the channel.  The angles made by the shroud were transferred to the tape.  I dimpled the wale where the toe of the lower link and the lower preventer chain bolts will be located and removed the tape.

A hole was drilled through the wale where the toe of the lower link would later be bolted.  The lower link and deadeye were temporarily installed. The length of the middle chains was determined by trial and error.  With the deadeye and lower link in place, I formed the middle link from rope the same thickness as the wire and transferred those lengths to wire.  I formed the middle link and soldered it closed, keeping the joint on one of the long sides.  Then I inserted the lower link through the middle link and soldered it. 

A T-pin was pushed into the soldering board and used to form the lower link toe.  The lower link is also bent at the toe, allowing it to lay flat against the wale. 

Finally, the wire for the upper link was passed through the middle link and  soldered.  The deadeye was inserted into the loop and the wire was crimped around it to fit into the channel slot, placing the solder joint in the slot camouflaged it.  

And here are the ten chains, ready for blackening.  The blackening chemical did not damage the wood deadeyes. 

 
After blackening, the chains were installed.  I have a piece of wire temporarily holding the lower link to the wale. 

The preventer plate prevents the bolt securing the lower link from going all the way through the toe. It was made from square bar stock that was forged to the correct shape.  Mine are made from sheet brass, cut and filed to the correct shape.  Just like the middle links, they varied in length. The top of the plate makes a step over the bottom of the lower link toe to cover it. To determine the distance between the bolt holes on the plate, I measured the distance between the toe bolt and the previously marked lower preventer plate bolt and added the diameter of the wire the link was made from.  The sequence is shown in the drawing below. After they were finished, they were blackened and installed.  

To hold the upper links in the channels, a strip of molding was placed over them.  Next up, the rigging begins.

 

Thank you ccoyle the whole model has progressed through each part of build log, constantly having little ideas, some from looking at old photos and some from visiting the Mikasa museum, some from artistic license, the final part with the raised waterline was always in my head, the three quarter effect stems from deciding to display torpedo net extended, anyone deciding on this for their build, would recommend fitting this last as it’s so very easy to knock and damage it am speaking from experience, l damaged it at least three times, very frustrating, only just finished making it a bit better now, never as good as my first attempt though, trying to keep those guy wires straight is a mission for sure. Can safely say won’t be doing another one, that’s me got that out of my system for good 😂  Regarding awards, that was just  so incredibly, never experienced anything like this before but shall always remember humbly the experience. Thanks again ccoyle. 🤛

Oh, there was already some information from you that helped me with my model. Of course, it is always much easier and requires less research when you can use such a detailed report. Funnily enough, it was user CDW's model that brought me to the Mikasa. And don't worry, I'm not a fan of quick construction, I worked on my Battleship Bismarck for almost two and a half years.
So thank you again for sharing this report with us.

Congratulations with the marvelous model, the inspiring buildlog and the many trophys

Wow! That is a fantastic model and display! The awards are well-deserved. Congratulations!

Stupendous result Jeff! What an awesome model. A lot of painstaking work I know but you really brought it home.