harlequin Posted May 28, 2015 Share #1 Posted May 28, 2015 (edited) are they flush with the planking or slightly set back inside the hull......the plans on Bellona look like they are flush, but I'm not sure that is right. In this pic they are flush with surrounding planks, or do they need to be set back into the hull slightly. Edited May 28, 2015 by harlequin Quote Link to comment Share on other sites More sharing options...
jbshan Posted May 28, 2015 Share #2 Posted May 28, 2015 The outer layer of the lid will be the same thickness as the hull planking, so the lining should be held back by that amount. mtaylor, augie and Landlubber Mike 3 Quote Joel Sanborn http://modelshipworld.com/index.php/topic/9953-lexington-by-jbshan-dlumberyard-164-from-the-seaways-practicum-by-clay-feldman/ Link to comment Share on other sites More sharing options...
harlequin Posted May 28, 2015 Author Share #3 Posted May 28, 2015 yep that's what I thought .cheers. Quote Link to comment Share on other sites More sharing options...
augie Posted May 28, 2015 Share #4 Posted May 28, 2015 Joel covered it. Quote Augie Current Build: US Frigate Confederacy - MS 1:64 Previous Builds : US Brig Syren (MS) - 2013 (see Completed Ship Gallery) Greek Tug Ulises (OcCre) - 2009 (see Completed Ship Gallery) Victory Cross Section (Corel) - 1988 Essex (MS) 1/8"- 1976 Cutty Sark (Revell 1:96) - 1956 Link to comment Share on other sites More sharing options...
Tadeusz43 Posted May 28, 2015 Share #5 Posted May 28, 2015 Hi, Gunport lids are flush with hull planking. See photo: 1 HMS Victory 2 Jylland Danish frigate 3 Drwg from Historic Ship Models by Wolfram zu Mondfeld Tadeusz robin b, Archi, butch and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Jaager Posted May 28, 2015 Share #6 Posted May 28, 2015 (edited) Although not addressed in the cross section schematic shown above, I am guessing that there is no Port lining at the sides. The sides are flush with the ends of the planking? No picture frame effect, just a recessed top and bottom layer? Edited May 28, 2015 by Jaager Quote NRG member 45 years Current: HMS Centurion 1732 - 60-gun 4th rate - Navall Timber framing HMS Beagle 1831 refiit 10-gun brig with a small mizzen - Navall (ish) Timber framing The U.S. Ex. Ex. 1838-1842 Flying Fish 1838 pilot schooner - framed - ready for stern timbers Porpose II 1836 brigantine/brig - framed - ready for hawse and stern timbers Vincennes 1825 Sloop-of-War - timbers assembled, need shaping Peacock 1828 Sloop-of -War - timbers ready for assembly Sea Gull 1838 pilot schooner - timbers ready for assembly Relief 1835 ship - timbers ready for assembly Other Portsmouth 1843 Sloop-of-War - timbers ready for assembly Le Commerce de Marseilles 1788 118 cannons - framed La Renommee 1744 Frigate - framed - ready for hawse and stern timbers Link to comment Share on other sites More sharing options...
mtaylor Posted May 28, 2015 Share #7 Posted May 28, 2015 Jaager, the sides would be the frames. The planking (when there are lids) goes just short of the opening to allow a lip (top, bottom and sides) for the lid to close on. robin b 1 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned) Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.