wefalck Posted January 16 Share #61 Posted January 16 What kind of belt-sander is it? mtaylor 1 Quote wefalck panta rhei - Everything is in flux Link to comment Share on other sites More sharing options...
DaKea90 Posted January 16 Author Share #62 Posted January 16 This one: It's relatively small, handy and has a small dustbin to the rear. The only downside is its noise, but you can counter it with even basic ear protection. wefalck, Ryland Craze and mtaylor 2 1 Quote Link to comment Share on other sites More sharing options...
wefalck Posted January 16 Share #63 Posted January 16 Ah, thought I thought it might have been the small PROXXON one ... mtaylor 1 Quote wefalck panta rhei - Everything is in flux Link to comment Share on other sites More sharing options...
DaKea90 Posted January 16 Author Share #64 Posted January 16 Proxxon would have been nice, but the Black&Decker did only cost less than a third (rather a quarter) as much as the Proxxon-equivalent. I was limited by the budget of the person, who wanted to give me this present after all. mtaylor 1 Quote Link to comment Share on other sites More sharing options...
mtaylor Posted January 19 Share #65 Posted January 19 On 1/16/2024 at 12:44 PM, Strelok said: Proxxon would have been nice, but the Black&Decker did only cost less than a third (rather a quarter) as much as the Proxxon-equivalent. I was limited by the budget of the person, who wanted to give me this present after all. It does look like the Proxxon, So much so, I'm wondering if it's made under license? Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned) Link to comment Share on other sites More sharing options...
wefalck Posted January 19 Share #66 Posted January 19 The PROXXON is a lot smaller, I believe. mtaylor 1 Quote wefalck panta rhei - Everything is in flux Link to comment Share on other sites More sharing options...
DaKea90 Posted January 22 Author Share #67 Posted January 22 The Proxxon is smaller, indeed, but not by THAT much. The B&D's measurements are 19,6 x 45,4 x 14,4 cm; 1,2 Kilogramm, compared to 19,3 x 33 x 11,2 cm; 0,9 Kilogramm (both according to amazon). Yes, it's a thrid shorter shorter overall, but it's only 300 gramm lighter. Now for something completely different: Another bit of progress was made today GrandpaPhil, Meriadoc Brandybuck, wefalck and 1 other 4 Quote Link to comment Share on other sites More sharing options...
DaKea90 Posted January 26 Author Share #68 Posted January 26 The first planking is done. The next planking will be the main deck and then the passengers cabin. KARAVOKIRIS, wefalck, SighingDutchman and 6 others 9 Quote Link to comment Share on other sites More sharing options...
DaKea90 Posted January 28 Author Share #69 Posted January 28 I just realized that I will need to tear out the main deck again. Its planks are 1mm thick and as you can see, the windowsills of the passenger's cabin sit visibly less than one 1mm above the main deck. Fortunately, I have another template already printed out. mtaylor and Meriadoc Brandybuck 2 Quote Link to comment Share on other sites More sharing options...
DaKea90 Posted February 23 Author Share #70 Posted February 23 Hey some good progress has been made again. Mast, bowsprit, gaff and gaff sail boom are done. When I made the gaff sail boom, I made a small oopsie and had a little heart attack: I broke the "fork" that goes to the mast (Klaue in german), but I was able to repair it. The only hint that this happened is that the fork connects to the gaff sail boom in a slight angle. I'm fine with that, though. Here you can see the gaff, gaff sail boom and bowsprit painted and with all clamps, blocks and dead eyes attached I close my update with a picture of the current status of the hull. The mast is not yet glued in place. CiscoH, GrandpaPhil, JacquesCousteau and 3 others 6 Quote Link to comment Share on other sites More sharing options...
DaKea90 Posted August 28 Author Share #71 Posted August 28 It's been a while, but I've made a bit of progress today. I've almost completed planking the deck. There are only two itsy-bitsy planks right next to the kabin left to do. These will be done next time. I also think I will redo the framing for the hatches in front of the cabin. I think I'll use walnut for a nicer contrast. The deck fittings will be left until the hull is planked and done, just before installing the rigging. I hope, my next building session does not lie half a year in the future as the last one oO ccoyle, CiscoH, JacquesCousteau and 3 others 6 Quote Link to comment Share on other sites More sharing options...
DaKea90 Posted September 2 Author Share #72 Posted September 2 Soooo, progress! Woohoo The deck is done, so are the hatches and gangways. I had to realize that I have no tool, to remove the big hatches to replace the framing. I've also installed the stem and stern post. The thing that I'm pretty proud of is the jig where the hull can stand in. It's simple but it works - and will probably need a rework later on The next steps are the windows for the cabin and the planking of the hull can begin. Snug Harbor Johnny, CiscoH, wefalck and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.