Chuck

The figure is off scale for the model but looks really good just with the fire hearth.   So I made a mini diorama of sorts to display on my desk.  I used the old second hand aged stove, LOL.  Its one of Chris' figures as you would recognize.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

The figure is off scale for the model but looks really good just with the fire hearth.   So I made a mini diorama of sorts to display on my desk.  I used the old second hand aged stove, LOL.  Its one of Chris' figures as you would recognize.
 

Indeed you are correct.  The humidity will take care of it.  Its best not to spray that.  After a day or so it gets fixed on its own.  I forgot to mention that.  
 
Chuck

Thanks guys.   Yes I could make this a mini kit.  I just dont have enough brass rod at the moment.  I have to source more of it and then I could make a small base for it like I did for the Winnie stove.  
 
Chuck

Step by Step...
 

1. Laser cut cedar brickwork.   Lightly sand the char.  But not so much that you remove the etched mortar lines.   Just a little.  Especially on the edges of the pieces.   Many have bricks etched on both sides.
apply wipe on poly when finished...this is important to seal the wood a bit.
 

2. Yes its bright!!   But this is just the initial steps.  I used a red promarker, you can see which color to add the base coat of red to all faces of the brickwork.  Also note the two pieces that make up the sides have been glued together.  Make sure you have the holes and pieces facing the correct direction.
 

3.  Glue the sides to the back wall.  Keep nice right angles.   Also add the front piece.   This is left a bit long and you will have to trim it to fit.  DO NOT glue to the base.  This will be done much later in the project.   Much, much later.
 

4.  Using weathering powder add some red/brown colors and dark browns to suit.   It depends on how weathered you want to go with the fire hearth.  You will see this at the end.   Spray all the pieces lightly with some matte spray fixative when you are done.
 

5.  This is where the magic happens.   You could use white weathering powder but that would also pigment the bricks.  You dont really want that.   So instead use regular white flour.   Brush it on and push it into the mortar lines which are made pretty deep for you.   Dont go for a perfect even coverage here.  Experiment a little.  Push it in the cracks with your finger....pack it in there.  Then brush it off the brick faces with a light touch.  Experiment for the look you really want...use some additional weathering powders if you want to add soot and ash.   Make it a used hearth or a relatively new one!!!  Also note the frame on the base was painted black.  Dont spray with fixative.  The normal humidity in the air will fix the flour in position on its own.  It may take a day or so depending on the weather.  
 



6.  1/32" brass wire/rod (not included) were blackened and added as shown above.
 

 
7.  The hood...laser cut from 1/64" thick boxwood.   Glue the shorter back piece on the base first.  It should be a at a perfect right angle vertically and centered.

8.  Add the two sides.  You will need to bevel the bottom to sit flush on the base.
 

9.  Add the front piece...which is taller than the back piece.  Note how the front hangs over the the front of the base just a bit.  That is done on purpose.  It is correct.

10.  Finally add the top and front pieces.   apply filler to all the cracks and sand smooth for painting.   Also build the stack the same way and prepare for painting.
 

11. Hinges are laser board.   Construct them in the sequence shown above...left to right.   First add the bottom half of all the hinges.  Then the hinge pins are glued along the top edge.  Use 24 gauge black wire for that.  To finish that up,  set the top half of the hinges above the wire.  An eyebolt is also added in the center.  You can see that in the photos below of the finished fire hearth.  There are two of them shown...
 
A beat up used and weathered fire hearth....and a shiny almost new hearth.   Have fun with it and weather to your preferred tastes.  LOL
 



NOTE....the hearth is NOT glued to the base yet.  And the stack is NOT glued to the hood yet.  It is best to keep them separate for now. 
 
 
 

Ship modelers and comedians!!!  LOL

No mistake....just a personal preference.   Once the deck is framed and planked overhead, it will hardly be seen.  Just a glimpse of it.  And it will be a nice surprise of a glimpse....
Yes...one can make it shiny new if they want to.   
 
I instead will pretend that my model portrays the ship only one month after launch, LOL.   If you use the hearth just a few times it will get full of soot and ash....while the other parts of the ship still look like new.  
 
Chuck

Nope…Im not that crazy.   The brickwork  is laser cut and etched in just six pieces.  Its actually much easier to build than a traditional iron stove.  Once I lasercut the parts this test mock up only took about four hours.  That was after many failed attempts however where each piece had to be tweaked and recut for a better fit.  But the last complete mock-up went together really easily.  
 
…just a hint of the technique for the brickwork.  Ordinary flour was used for the mortar between the bricks once the red color was completed.  Its a really neat trick and really finishes everything nicely.  I hope you agree.
 
I guess it is still a bit crazy seeing how its a lot of work for an item that will hardly be seen.  LOL

Finishing up the platforms with the ringbolts for the scuttle lids.  I also made a quick mock-up today of the fire hearth.  Unlike the Seawatch books I am deviating from the traditional stove.   I have built a lot of traditional iron stoves in my time.   Based on the original drafts and on the draft for the similar sloop Fly I am going with a brick fire hearth.   The contemporary draft is shown in the photos below.  You can clearly see the bricked up hearth.  I think it is a much more interesting fixture and its something I have never modelled before.  You guys can go either way...its up to you.  But I will only be making a mini kit for the fire hearth for the model.  This was actually very typical for sloops of this time period and I found a great deal of source info for these.
 
All of the brickwork is lasercut cedar.  The hood parts are thin boxwood sheet with laserboard hinges.   I will of course have to make another because I didnt take step by step photos.   I used a really easy and neat technique to weather those bricks.  I will detail that when the time comes.
 
The fire hearth isnt permanently added yet.   I will however glue the base onto the platform at this time.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

The figure is off scale for the model but looks really good just with the fire hearth.   So I made a mini diorama of sorts to display on my desk.  I used the old second hand aged stove, LOL.  Its one of Chris' figures as you would recognize.
 

Step by Step...
 

1. Laser cut cedar brickwork.   Lightly sand the char.  But not so much that you remove the etched mortar lines.   Just a little.  Especially on the edges of the pieces.   Many have bricks etched on both sides.
apply wipe on poly when finished...this is important to seal the wood a bit.
 

2. Yes its bright!!   But this is just the initial steps.  I used a red promarker, you can see which color to add the base coat of red to all faces of the brickwork.  Also note the two pieces that make up the sides have been glued together.  Make sure you have the holes and pieces facing the correct direction.
 

3.  Glue the sides to the back wall.  Keep nice right angles.   Also add the front piece.   This is left a bit long and you will have to trim it to fit.  DO NOT glue to the base.  This will be done much later in the project.   Much, much later.
 

4.  Using weathering powder add some red/brown colors and dark browns to suit.   It depends on how weathered you want to go with the fire hearth.  You will see this at the end.   Spray all the pieces lightly with some matte spray fixative when you are done.
 

5.  This is where the magic happens.   You could use white weathering powder but that would also pigment the bricks.  You dont really want that.   So instead use regular white flour.   Brush it on and push it into the mortar lines which are made pretty deep for you.   Dont go for a perfect even coverage here.  Experiment a little.  Push it in the cracks with your finger....pack it in there.  Then brush it off the brick faces with a light touch.  Experiment for the look you really want...use some additional weathering powders if you want to add soot and ash.   Make it a used hearth or a relatively new one!!!  Also note the frame on the base was painted black.  Dont spray with fixative.  The normal humidity in the air will fix the flour in position on its own.  It may take a day or so depending on the weather.  
 



6.  1/32" brass wire/rod (not included) were blackened and added as shown above.
 

 
7.  The hood...laser cut from 1/64" thick boxwood.   Glue the shorter back piece on the base first.  It should be a at a perfect right angle vertically and centered.

8.  Add the two sides.  You will need to bevel the bottom to sit flush on the base.
 

9.  Add the front piece...which is taller than the back piece.  Note how the front hangs over the the front of the base just a bit.  That is done on purpose.  It is correct.

10.  Finally add the top and front pieces.   apply filler to all the cracks and sand smooth for painting.   Also build the stack the same way and prepare for painting.
 

11. Hinges are laser board.   Construct them in the sequence shown above...left to right.   First add the bottom half of all the hinges.  Then the hinge pins are glued along the top edge.  Use 24 gauge black wire for that.  To finish that up,  set the top half of the hinges above the wire.  An eyebolt is also added in the center.  You can see that in the photos below of the finished fire hearth.  There are two of them shown...
 
A beat up used and weathered fire hearth....and a shiny almost new hearth.   Have fun with it and weather to your preferred tastes.  LOL
 



NOTE....the hearth is NOT glued to the base yet.  And the stack is NOT glued to the hood yet.  It is best to keep them separate for now. 
 
 
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

The figure is off scale for the model but looks really good just with the fire hearth.   So I made a mini diorama of sorts to display on my desk.  I used the old second hand aged stove, LOL.  Its one of Chris' figures as you would recognize.
 

Lovely!!

Outstanding

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

Step by Step...
 

1. Laser cut cedar brickwork.   Lightly sand the char.  But not so much that you remove the etched mortar lines.   Just a little.  Especially on the edges of the pieces.   Many have bricks etched on both sides.
apply wipe on poly when finished...this is important to seal the wood a bit.
 

2. Yes its bright!!   But this is just the initial steps.  I used a red promarker, you can see which color to add the base coat of red to all faces of the brickwork.  Also note the two pieces that make up the sides have been glued together.  Make sure you have the holes and pieces facing the correct direction.
 

3.  Glue the sides to the back wall.  Keep nice right angles.   Also add the front piece.   This is left a bit long and you will have to trim it to fit.  DO NOT glue to the base.  This will be done much later in the project.   Much, much later.
 

4.  Using weathering powder add some red/brown colors and dark browns to suit.   It depends on how weathered you want to go with the fire hearth.  You will see this at the end.   Spray all the pieces lightly with some matte spray fixative when you are done.
 

5.  This is where the magic happens.   You could use white weathering powder but that would also pigment the bricks.  You dont really want that.   So instead use regular white flour.   Brush it on and push it into the mortar lines which are made pretty deep for you.   Dont go for a perfect even coverage here.  Experiment a little.  Push it in the cracks with your finger....pack it in there.  Then brush it off the brick faces with a light touch.  Experiment for the look you really want...use some additional weathering powders if you want to add soot and ash.   Make it a used hearth or a relatively new one!!!  Also note the frame on the base was painted black.  Dont spray with fixative.  The normal humidity in the air will fix the flour in position on its own.  It may take a day or so depending on the weather.  
 



6.  1/32" brass wire/rod (not included) were blackened and added as shown above.
 

 
7.  The hood...laser cut from 1/64" thick boxwood.   Glue the shorter back piece on the base first.  It should be a at a perfect right angle vertically and centered.

8.  Add the two sides.  You will need to bevel the bottom to sit flush on the base.
 

9.  Add the front piece...which is taller than the back piece.  Note how the front hangs over the the front of the base just a bit.  That is done on purpose.  It is correct.

10.  Finally add the top and front pieces.   apply filler to all the cracks and sand smooth for painting.   Also build the stack the same way and prepare for painting.
 

11. Hinges are laser board.   Construct them in the sequence shown above...left to right.   First add the bottom half of all the hinges.  Then the hinge pins are glued along the top edge.  Use 24 gauge black wire for that.  To finish that up,  set the top half of the hinges above the wire.  An eyebolt is also added in the center.  You can see that in the photos below of the finished fire hearth.  There are two of them shown...
 
A beat up used and weathered fire hearth....and a shiny almost new hearth.   Have fun with it and weather to your preferred tastes.  LOL
 



NOTE....the hearth is NOT glued to the base yet.  And the stack is NOT glued to the hood yet.  It is best to keep them separate for now.