tlevine

Out of curiosity I visited the pirates forum and read the article about Chuck's Speedwell. I had a really good laugh at the comment by one of their admin wallahs. "Luckily we have same quality kits from Chinese manufacturers at one third of the price". Quality ???? What planet is that guy on ? Keep up the good work Chuck,I enjoy following your build. Sorry I wont be building your Speedwell as I've started rigging my 1/48th POB version after 5 years of work .  
 
Dave 

I don’t think so. There is also a lot of support for you there. 
 
The description of how you make and prepare your gratings shows again what I mean in my last post. I can prepare the gratings with my small CNC-mill and build the jig following your really good description. Thanks very much.

Tom, I like Chuck's method because it incorporates the round up. That might be possible on the mill but it's above my pay grade.

That would be so nice but it probably would put the builder at risk of being abused.
 
Anyway....those gratings
 
You will basically get all of the laser cut parts in this chapter.  There are only four hatches with gratings.  They are not very large.   Here are all of the elements needed.  You will get two layers for the jig.   The two layers are glued together to form the jig.
 
You also get a right angle jig which is 3/64" thick.  The thickness is very important.
 
Lets get started.
 

Start with the coamings.   They are laser cut and 1/8" thick.
 
The fore and aft sides are already shaped with the round-up of the deck....or camber as usually described but is an inaccurate term.
 
Use the right angle jig to glue two sides together...dont worry about the laser char just yet.   Then glue the remaining two sides together using the same jig to make a nice right angle.
 

Glue the two right angles together to form the coaming.  Sand the sides clean which are left a bit longer as you can see in order to remove the char and leave a nice bright smooth surface.   Also sand the top sides to clean the char.  You can see the cleaned coaming below.
 
Then you can start working on the grating.  Again just like my other smaller scale grating kits.
 
Insert the laser cut grating strips in the slotted jig.  NO GLUE of course!!!   This is just for alignment.
 
Then start adding the cross battens.  These are glued in position.  They may be too tight as you want a press fit.  So just run the small strips 1/16" x 1/16" through your fingers with some fine sandpaper.  Not much.  Just enough so the battens fit into the slots. see below.  There are seven batten strips and seven laser cut grating strips for three of the hatches.  The fourth is made the same way but is much smaller on the fcastle.
 

When all the strips are glued in position,  remove the grating from the jig.  Snip off the edges as shown below.  Then sand all four edges clean.  Try and not distort the perfect square shape.  In the photo two sides have the ends snipped off.   The smaller hatchway will have fewer battens and more to snip away.  Also sand the top surface clean and smooth.  Once again try and maintain the proper shape with the round-up.  You will know when its all done when the char is cleaned from the laser cut grating strip squares.

The photo below shows the top of the grating and sides all clean and nice and smooth.  It makes a nice grating.  The holes are 1/16" or 2" on the real ship and perfectly in scale.

You should but dont have to sand the bottom side as well.   Here is a look.  The battens are clearly less thick than the grating strips and these are pretty close to actual construction methods.  Or at least the impression of it.
 

And almost done...you will see how nice and tight the grating fits in the coaming.   Dont over sand the edges and you should test the grating in the coaming as you sand the edges.   In fact, the coaming normally has ledges on the port and starboard sides inside the coaming.  These create a ledge that the grating sits on so it doesnt fall through.  You can add those if you like.  But in my case the gratings fit so snug that they were not required.  I simply glued the gratings into the coamings making sure the top of the coaming was flush with the grating.  I sanded it smooth with some 400 grit paper.

The four corners of the coaming are very sharp at this point.  You dont want that.  They should be rounded off.  But they are only rounded off down to the deck level.   That is when you take that same right angle jig and use it.
 
The jig is the same thickness as the planking.   So you can place the coaming into the corner and use a sharp #11 blade to slice away the corner.  Slice it down to the top of the jig only.   You can make a stop cut at the jig level before slicing off the corner.  Then just round off the corner.
 
 
Dont slice off too much.   Just a little bit to round off each corner.
 
To finish it off I drilled three holes with a #76 bit.  I used 20lb black fishing line to simulate the bolts on the top of the coamings.  Three on each side.   They cut flush with the top of the coamings with a sharp blade.
 
All done!!!
 
 
 

It woul be a lot of fun to make a build log of your kit there.
I love your ideas and how open you share your knowledge. Without this I was not able to finish the frame design for my Alert. I also learned a lot to continue with my Sloop Fly. Thanks for that.

Excuse the newbie ignorance but I assume that is another forum?
Again as a newbie to the hobby I can't imagine (other than insecurity and jealousy( what folk can say negatively about your work. Having looked at a lot of kits before moving on from my first (admittedly online) the only kits I really wanted to try were yours and Vanguards. On all of the build logs here it comes across so strongly how high the quality of both your kits are to give any stage of modeller the very best chance of making something stunning. Yes they are expensive but you get what you pay for in most areas and this is definitely one.
Good luck to you!
 

I am just about to post an update with those...LOL
 
The gratings for Speedwell are different but the same basic concept.  They are a different scale to reflect the larger size needed.  They will have 1/16" square openings which at 3/8" scale would be a 2" hole.  Just right and exactly the same number of holes as the contemporary model.
 
These will all be included in the chapter along with the jig needed.
 
I will have construction pics really soon.
 
I have been distracted lately with the topic on the SOS where the staff and admin are trashing this project relentlessly....but its a lot fun to watch.   Many of you guys have sent me messages alerting me about it.
 
I have to thank Ben however for being a brave soul to have something nice to say about it knowing he will get the wrath for it.   I must be the worst kit designer in the world if you read some of that stuff over there.  But seriously...dont put yourself out there because if you do say anything positive about Syren or any of my projects on SOS they will lambaste you.  So no worries.   Dont put yourself in that position.  Its not worth it.   Most folks know its all nonsense.  And I am well aware.  But thanks for the positive notes of private support.
 
Anyway...back to building gratings.

steps.....
 






 

I own a small CNC. What has changed is the precision for cutting out parts. So you begin to think about problems, which you not have, if you cut out parts manually. The model is further build by the model builder. The quality depends further on the knowledge and experience of the builder.
I prepare my parts directly from my own reconstruction with the CNC. By all the precision It is not possible for me to build my model in the quality you are showing here. I simply love it.
 
I do not like competitions for my hobby and will never participate in one.
 

Like the rug in the classic movie "The Big Lebowski" it ties the whole thing together.  Such a beautiful model!

I agree, I personally don't have very good memories of the judges in Croatia either (I participated there with Pandora). And as for the "new" group of CNC models, maybe that will happen one day, just as a new category for kit models (C8) was established. I wish you a lot of fun building a beautiful model (after all, that's why we build models - for fun).

Hello,
it is done. At least the wheels are ready build. Next to build are the two supporters for the wheels.

It is time to start rigging the mast.  Some lines are served with an additional layer of line wrapped around them to protect them wherever they would be at risk of damage from rubbing.  On this model, the pendant of tackles, the foremost shroud, the other shrouds above the catharpins and the jeer block strop are served.  Because this is a cross-section, the main and back stays will not be installed but they would also be served.  Standing rigging is protected from water damage with a tar-like compound.  This resulted in a dark brown appearance to the lines.  The running rigging was not protected and so was a natural hemp color.  On this model, the burton pendants and shrouds are standing rigging;  everything else is running rigging
 
Rope sizes are calculated from the diameter of the mast.  The kit contains a table with the dimensions for the various ropes, based on the diameter of the mast.  To measure the diameter of the line, I wrap it around a dowel twenty times, measure the width of the wrapping and divide by twenty.  This is much more accurate than  trying to measure an individual line. The first rope to go over the masthead is the pendant of tackles.  On the topmast, this line is referred to as the burton pendant.  This rope is completely served, and has a thimble on one end.  The other end is spliced to its opposite, resulting in the rope in the diagram below.  Where the red and blue lines meet are splices.  The pendants extend to approximately two feet below the hounds.  They were used with a tackle to raise and lower heavy weights.

To properly rig a model there is no substitute for the appearance of a served line.  I use 6-0 fly tying thread, which can be purchased at a sporting goods store or online.  I start by running thread, from left to right in this case, into the depression between the rope strands (worming), smoothing its surface (the yellow areas seen in the drawing below.  Then I serve the rope from right to left. 

I find it easier to serve short segments of rope, such as this, on the same piece of rope and then cut them apart.  I served the rope, leaving approximately six inches of serving thread for the splices (red circles).

Then I made a diagonal cut, following the lay of the rope ¼” away from the end of the serving.  The unserved line was held against the other line where the splice would go and I wrapped the two lines with the left-over serving thread “splicing” them together.  I continued the wrapping a few more twists to smooth out the transition and tied it off.  A tiny bit of dilute glue held everything together. The pendant was put over the mast head and onto the bolsters.  It was marked on each leg, two feet below the hounds and removed from the mast.  I used blackened 1/16” ID brass tubing for my thimbles.  The mark was placed on the side of the thimble and the pendant was wrapped around it.  For simplicity I used a simple seizing to secure the thimble and put it back on the mast.

 
 
 
 

What a difference some paint makes.   Bulwarks are painted however as usual, I will be applying many more thin coats over the next few weeks as I progress.   
 
Before and after...
 

 

Hello,
because today the summer ended we had here the last weeks and it rained again the whole day, I was busy at the yard. 
This is cutter No. 3 and I think now it works. The handles are a little too bulky, but when they are slimmer they would break. The spooks have a Ø of 1,6 mm!


Now are only 17+ spooks left

It is interesting to see the difference between the European and US/Canadian situations.  In the States, there are few contests and a few non-competitive shows.  Although some models are built by people who accept commissions, I would not describe them as professional modelers.  Your Pegasus is beautiful and deserves to be appreciated by the modelling community.

It is interesting to see the difference between the European and US/Canadian situations.  In the States, there are few contests and a few non-competitive shows.  Although some models are built by people who accept commissions, I would not describe them as professional modelers.  Your Pegasus is beautiful and deserves to be appreciated by the modelling community.

It is interesting to see the difference between the European and US/Canadian situations.  In the States, there are few contests and a few non-competitive shows.  Although some models are built by people who accept commissions, I would not describe them as professional modelers.  Your Pegasus is beautiful and deserves to be appreciated by the modelling community.

It is time to start rigging the mast.  Some lines are served with an additional layer of line wrapped around them to protect them wherever they would be at risk of damage from rubbing.  On this model, the pendant of tackles, the foremost shroud, the other shrouds above the catharpins and the jeer block strop are served.  Because this is a cross-section, the main and back stays will not be installed but they would also be served.  Standing rigging is protected from water damage with a tar-like compound.  This resulted in a dark brown appearance to the lines.  The running rigging was not protected and so was a natural hemp color.  On this model, the burton pendants and shrouds are standing rigging;  everything else is running rigging
 
Rope sizes are calculated from the diameter of the mast.  The kit contains a table with the dimensions for the various ropes, based on the diameter of the mast.  To measure the diameter of the line, I wrap it around a dowel twenty times, measure the width of the wrapping and divide by twenty.  This is much more accurate than  trying to measure an individual line. The first rope to go over the masthead is the pendant of tackles.  On the topmast, this line is referred to as the burton pendant.  This rope is completely served, and has a thimble on one end.  The other end is spliced to its opposite, resulting in the rope in the diagram below.  Where the red and blue lines meet are splices.  The pendants extend to approximately two feet below the hounds.  They were used with a tackle to raise and lower heavy weights.

To properly rig a model there is no substitute for the appearance of a served line.  I use 6-0 fly tying thread, which can be purchased at a sporting goods store or online.  I start by running thread, from left to right in this case, into the depression between the rope strands (worming), smoothing its surface (the yellow areas seen in the drawing below.  Then I serve the rope from right to left. 

I find it easier to serve short segments of rope, such as this, on the same piece of rope and then cut them apart.  I served the rope, leaving approximately six inches of serving thread for the splices (red circles).

Then I made a diagonal cut, following the lay of the rope ¼” away from the end of the serving.  The unserved line was held against the other line where the splice would go and I wrapped the two lines with the left-over serving thread “splicing” them together.  I continued the wrapping a few more twists to smooth out the transition and tied it off.  A tiny bit of dilute glue held everything together. The pendant was put over the mast head and onto the bolsters.  It was marked on each leg, two feet below the hounds and removed from the mast.  I used blackened 1/16” ID brass tubing for my thimbles.  The mark was placed on the side of the thimble and the pendant was wrapped around it.  For simplicity I used a simple seizing to secure the thimble and put it back on the mast.

 
 
 
 

I did a variety of things over the last week.  I built the jib outhaul block (shown in the painfully enlarged photo below . . . warts and all, haha).  Mike (stuntflyer) has an excellent tutorial for that on his Cheerful build, so I followed that.  I then made a card stock mock up of the starboard side seat.  I used the card stock templates as a pattern to cut out the parts.  As others have said this is a bit finicky.  I have a feeling the second one will be more of a challenge as I try to get it to match the first.
 
I spent some time this week reading ahead in Chuck's monograph chapters to get a list of the last little bits I need to finish the build.  I ordered some Albion Alloys brass tube.  I also messaged Chuck, Mike, and Glenn (glbarlow) with questions about the thread type/size/color they used with Chuck's scale rope for seizing and serving.  Today I went on a region wide road trip to fly fishing shops and fabric stores.  Most of my dark brown rope is Chuck's old style rope, other than the .012" new Ultra for rat lines (so I don't need thread for seizing or serving the brown Ultra rope).  My tan rope is a mix of his old rope and the new Ultra rope.  These tan colors are close enough in shade to mix on the model, but I wanted thread for seizing that matched each shade.  The photos below are color corrected to be as close to accurate as I could possibly get the images.  The Gutermann thread is for most serving and seizing.  The smaller diameter UNI-Thread fly tying thread is for tiny serving and seizing.
 
Here's what I came up with based on what I could find locally.
Using with Syren old brown rope - Gutermann 50wt CA02776 Polyester thread Color 593 - UNI-Thread 72D 8/0W Dark Brown
Using with Syren old tan rope - Gutermann 50wt CA02776 Polyester thread Color 512 - UNI-Thread 72D 8/0W Tan
Using with Syren new Ultra tan rope - Gutermann 50wt CA02776 Polyester thread Color 509 - also UNI-Thread 72D 8/0W Tan
 
Also, as Chuck had answered, the thread he uses for seizing and serving his new Ultra rope is as follows (I researched what actual size/diameter it is in wt and tex).
Ultra Brown rope - Gutermann Mara 150 50wt/20Tex  Color 682 or for smaller uses Mara 220 77wt/13Tex
Ultra Tan rope - Gutermann Mara 150 50wt/20Tex  Color 263 or for smaller uses Mara 220 77wt/13Tex
This is hard to find in the US, so Chuck recommended this place: https://www.williamgee.co.uk/product-tag/mara/
 
Erik
 

Many of you are curious about this photo.   Its floating around the forums without an explanation.  I brought my Medway Longboat to the New London show last week where it was photographed..   You may not be able to see it right away but yes I changed this Medway English longboat to be an American boat.   This model was used in the movie that I worked on last year which I talked about a while back.   I changed the flag and the nameplate on the model.  They wanted it to be American and have the Character's Name on the model.  They were going to slowly pan across it for the movie and wanted Ed Harris' character name very visible etc.
 
To my Surprise after spending a bunch time with him trying to teach him how to fake being a ship modeler,   Ed Harris signed the model.  But of course not the base....Black sharpie right across the hull.   No fixing that!!!  So rather than put the model back to its original English origin and remove the nameplates, I decided to just leave it as is.  It will make for a nice conversation piece.   The movie is supposed to come out in July I believe....It was about 10 degrees out the day he signed it.  The workshop was set up in the garage of the set.  I have no idea how they acted as if it wasnt freezing all the time.  I suppose that is why he is considered such a great actor.
 
Starring Ed Harris, Dustan Hoffman, Bill Murray, Gabrielle Union, Jenifer Coolidge, Pete Davidson and a bunch of others you would certainly know.   We shall see how the movie turned out!!!   At least I have a memento for the wonderful experience.
 

Hello,
the first results.  I think, tomorrow I have to make the cutter new. But it is an interesting material and cuts better then wood. 

It is time to start rigging the mast.  Some lines are served with an additional layer of line wrapped around them to protect them wherever they would be at risk of damage from rubbing.  On this model, the pendant of tackles, the foremost shroud, the other shrouds above the catharpins and the jeer block strop are served.  Because this is a cross-section, the main and back stays will not be installed but they would also be served.  Standing rigging is protected from water damage with a tar-like compound.  This resulted in a dark brown appearance to the lines.  The running rigging was not protected and so was a natural hemp color.  On this model, the burton pendants and shrouds are standing rigging;  everything else is running rigging
 
Rope sizes are calculated from the diameter of the mast.  The kit contains a table with the dimensions for the various ropes, based on the diameter of the mast.  To measure the diameter of the line, I wrap it around a dowel twenty times, measure the width of the wrapping and divide by twenty.  This is much more accurate than  trying to measure an individual line. The first rope to go over the masthead is the pendant of tackles.  On the topmast, this line is referred to as the burton pendant.  This rope is completely served, and has a thimble on one end.  The other end is spliced to its opposite, resulting in the rope in the diagram below.  Where the red and blue lines meet are splices.  The pendants extend to approximately two feet below the hounds.  They were used with a tackle to raise and lower heavy weights.

To properly rig a model there is no substitute for the appearance of a served line.  I use 6-0 fly tying thread, which can be purchased at a sporting goods store or online.  I start by running thread, from left to right in this case, into the depression between the rope strands (worming), smoothing its surface (the yellow areas seen in the drawing below.  Then I serve the rope from right to left. 

I find it easier to serve short segments of rope, such as this, on the same piece of rope and then cut them apart.  I served the rope, leaving approximately six inches of serving thread for the splices (red circles).

Then I made a diagonal cut, following the lay of the rope ¼” away from the end of the serving.  The unserved line was held against the other line where the splice would go and I wrapped the two lines with the left-over serving thread “splicing” them together.  I continued the wrapping a few more twists to smooth out the transition and tied it off.  A tiny bit of dilute glue held everything together. The pendant was put over the mast head and onto the bolsters.  It was marked on each leg, two feet below the hounds and removed from the mast.  I used blackened 1/16” ID brass tubing for my thimbles.  The mark was placed on the side of the thimble and the pendant was wrapped around it.  For simplicity I used a simple seizing to secure the thimble and put it back on the mast.

 
 
 
 

It is time to start rigging the mast.  Some lines are served with an additional layer of line wrapped around them to protect them wherever they would be at risk of damage from rubbing.  On this model, the pendant of tackles, the foremost shroud, the other shrouds above the catharpins and the jeer block strop are served.  Because this is a cross-section, the main and back stays will not be installed but they would also be served.  Standing rigging is protected from water damage with a tar-like compound.  This resulted in a dark brown appearance to the lines.  The running rigging was not protected and so was a natural hemp color.  On this model, the burton pendants and shrouds are standing rigging;  everything else is running rigging
 
Rope sizes are calculated from the diameter of the mast.  The kit contains a table with the dimensions for the various ropes, based on the diameter of the mast.  To measure the diameter of the line, I wrap it around a dowel twenty times, measure the width of the wrapping and divide by twenty.  This is much more accurate than  trying to measure an individual line. The first rope to go over the masthead is the pendant of tackles.  On the topmast, this line is referred to as the burton pendant.  This rope is completely served, and has a thimble on one end.  The other end is spliced to its opposite, resulting in the rope in the diagram below.  Where the red and blue lines meet are splices.  The pendants extend to approximately two feet below the hounds.  They were used with a tackle to raise and lower heavy weights.

To properly rig a model there is no substitute for the appearance of a served line.  I use 6-0 fly tying thread, which can be purchased at a sporting goods store or online.  I start by running thread, from left to right in this case, into the depression between the rope strands (worming), smoothing its surface (the yellow areas seen in the drawing below.  Then I serve the rope from right to left. 

I find it easier to serve short segments of rope, such as this, on the same piece of rope and then cut them apart.  I served the rope, leaving approximately six inches of serving thread for the splices (red circles).

Then I made a diagonal cut, following the lay of the rope ¼” away from the end of the serving.  The unserved line was held against the other line where the splice would go and I wrapped the two lines with the left-over serving thread “splicing” them together.  I continued the wrapping a few more twists to smooth out the transition and tied it off.  A tiny bit of dilute glue held everything together. The pendant was put over the mast head and onto the bolsters.  It was marked on each leg, two feet below the hounds and removed from the mast.  I used blackened 1/16” ID brass tubing for my thimbles.  The mark was placed on the side of the thimble and the pendant was wrapped around it.  For simplicity I used a simple seizing to secure the thimble and put it back on the mast.

 
 
 
 

It is time to start rigging the mast.  Some lines are served with an additional layer of line wrapped around them to protect them wherever they would be at risk of damage from rubbing.  On this model, the pendant of tackles, the foremost shroud, the other shrouds above the catharpins and the jeer block strop are served.  Because this is a cross-section, the main and back stays will not be installed but they would also be served.  Standing rigging is protected from water damage with a tar-like compound.  This resulted in a dark brown appearance to the lines.  The running rigging was not protected and so was a natural hemp color.  On this model, the burton pendants and shrouds are standing rigging;  everything else is running rigging
 
Rope sizes are calculated from the diameter of the mast.  The kit contains a table with the dimensions for the various ropes, based on the diameter of the mast.  To measure the diameter of the line, I wrap it around a dowel twenty times, measure the width of the wrapping and divide by twenty.  This is much more accurate than  trying to measure an individual line. The first rope to go over the masthead is the pendant of tackles.  On the topmast, this line is referred to as the burton pendant.  This rope is completely served, and has a thimble on one end.  The other end is spliced to its opposite, resulting in the rope in the diagram below.  Where the red and blue lines meet are splices.  The pendants extend to approximately two feet below the hounds.  They were used with a tackle to raise and lower heavy weights.

To properly rig a model there is no substitute for the appearance of a served line.  I use 6-0 fly tying thread, which can be purchased at a sporting goods store or online.  I start by running thread, from left to right in this case, into the depression between the rope strands (worming), smoothing its surface (the yellow areas seen in the drawing below.  Then I serve the rope from right to left. 

I find it easier to serve short segments of rope, such as this, on the same piece of rope and then cut them apart.  I served the rope, leaving approximately six inches of serving thread for the splices (red circles).

Then I made a diagonal cut, following the lay of the rope ¼” away from the end of the serving.  The unserved line was held against the other line where the splice would go and I wrapped the two lines with the left-over serving thread “splicing” them together.  I continued the wrapping a few more twists to smooth out the transition and tied it off.  A tiny bit of dilute glue held everything together. The pendant was put over the mast head and onto the bolsters.  It was marked on each leg, two feet below the hounds and removed from the mast.  I used blackened 1/16” ID brass tubing for my thimbles.  The mark was placed on the side of the thimble and the pendant was wrapped around it.  For simplicity I used a simple seizing to secure the thimble and put it back on the mast.