Jump to content
New Publication - Ship Modeler's Handbook - Temp out of stock ×

HIPEXEC

Members
 View Profile  See their activity

  • Posts

    2,698

  • Joined

  • Last visited

 Content Type 

Everything posted by HIPEXEC

  1. HIPEXEC
    I masked the bow stem and keel since I do not know what I am doing with them yet and varnished all the planks to seal them. I used semi-gloss clear poly.
  2. HIPEXEC
    I decided to give all the veneer work a coat of varnish to "toughen" it up. It has a tendency to splinter when handled too much. The varnish will seal it. I've masked the few deck pieces I've installed since I don't want the deck varnished.
  3. HIPEXEC
    You are off to a great start. That's the neatest filler blocks I've ever seen. You should see my filler block mess. I'll be watching. Goos luck
  4. HIPEXEC
    I glued the first deck plank right down the center.
  5. HIPEXEC
    Well here's my hull without painting but it still gives the same dark/light look. I added some doo-dads to the stern to make it more pretty. The clamps on the bow are to show Heronguy that even at the state I'm in. The bowsprit is still vulnerable to breaking. I have been using these clamps since I broke off the bowsprit a while ago, but I still have to maneuver the hull where it could still be broken.
  6. HIPEXEC
    I glued on the margin planks with a little kentucky windage, forcing, bending and other acrobatics. It still isn't perfect but I have to eventually install waterways which should cover the small gaps.
  7. HIPEXEC
    It gets stronger after a while. I finally took all my supports off and I'm starting deck planking! This kit is a fragile mess until then. Nice recovery and repair
  8. HIPEXEC
    Frank, A guy named "GRIPHOS" is building a skipjack (Willie Bennet) and has questions about paint colors. Maybe you can help him Rich
  9. HIPEXEC
    I made the cut to match the laser cut pieces to my raw material. Tricky cut. Now I'll tweak the laser cut pieces to fit my hull. They are just a bit off.
  10. HIPEXEC
    Now I'm prepping for planking the deck. I framed the companionway and a long time ago I pre-drilled the holes for the masts. The kit comes with two laser cut deck framing pieces for the forward part near the bow that don't quite match the curve of my hull. I'll have to tweak them.
  11. HIPEXEC
    Port side top rail is now glued on. I only see one place on the starboard rail that will need my attention when the glue dries. I don't like the way it sits there. It will take some filling and sanding to make it right. Top rails are much easier when they come laser cut in the box. Making them yourself is many times harder.
  12. HIPEXEC
    Starboard top rail glued and being held flush with masking tape. I now am tweaking the port top rail to get the curves exactly.
  13. HIPEXEC
    I'm fine tune bending the cap rail. Pre-bent was just a little off. By the way, I sanded down the bulkheads to make them just a bit thinner than the cap rail as per the instructions.
  14. HIPEXEC
    Wow! Nice work.
  15. HIPEXEC
    I'm using Chuck Passaro's method of flat or edge bending the cap rails. Only I did soak it for a little bit.
  16. HIPEXEC
    I'm finishing the hull planking for the sliver I left off because that edge under the cap rail would have been too delicate while I planked the entire hull. I'm also bending the cap rail. The cap rails have to be bent flat side up which is difficult.
  17. HIPEXEC
    I finished the basic trim on the transom. I'm not sure if I like it or not? I'll keep looking at it and tweaking it.
  18. HIPEXEC
    It's another beauty!
  19. HIPEXEC
    I just make my own. This way I can have all sorts of sizes and shapes to get into weird places.
  20. HIPEXEC
    But with model ship building it's true. It's a challenge sometimes.
  21. HIPEXEC
    Yea! Old Farts Rule! I like that. By the way, your Connie looks great!
  22. HIPEXEC
    Cap trim on the transom is trickier than meets the eye. I got it on but I will have to do some artistic filling to make it look like I want it. Oh well, if it was easy anybody could do it.
  23. HIPEXEC
    Good recovery
  24. HIPEXEC
    The instructions call for me to finish the stern trimmings and cap rail before plunging into installing the decking. I pre-made the gold piece a while ago. I'm pre-shaping the stern cap trim. I am also shopping for 1/8" letters for the name "ARGUS" since the kit only comes with "SYREN" letters. The gold trim piece has been glued but the cap is just snapped on for photo purposes.
  25. HIPEXEC
    No copper plate....I like to look at wood

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...