Beef Wellington

@mugje - just to be clear, the resin hull shown is an 'aftermarket' mini-kit supplied by caldercraft, its not included in the kit.  What I'm attempting to do is leverage the kit supplied items as best I can.
 
Cutter Progress: Part 2
 
Keel and bow section was cut out of some spare wood and glued in place, and once the basic hull was completed, a decision was needed on how to add a second layer of planking, kit instructions specify to use another layer of 0.5mm walnut.  I really wanted to try and replicate the clinker hull planking shown in the AOTS Diana book, and to do this a used some cardstock instead of wood to cut individual strakes.  Fist challenge was to determine the width of each plank on the hull.  This was done using 'tick strips' at about 10 points along the hull.  The lowest (non-clinkered) garboard strake was simply omitted.  The end of the cardstock strips were cut down (rather than truly tapered) to allow the planking to terminate smoothly at the front bow and stern which is how I believe the planking is done in practice.  Each strip was cut to about 2.5mm thickness, the benefit of cardstock is that when coated with dilute PVA glue it becomes very manageable and can simply be bent to shape rather than the spiling that would have been necessary if wood had been used.
 
Once the hull had been marked out to 'prove' the planking separation, these were not referenced again.  Once a strip had been installed, the lowest point of the next strip was placed using the tickstrips.  This process was simply repeated, with time allowed for the glue to dry sufficiently for the surface to harden.  Dilute PVA was used quite liberally to ensure a good bond between the wood and card as the hope is for this to add additional structural strength.
 

 

 
The final 2 strakes were completed with one wider strip as the uppermost strake is non-clinkered and would not be visible.  Extra height was added for safety as this can be easily cut back once glue has dried.
 

 
Once both sides had been completed, each was  given a few more coats of dilute PVA for added insurance....why not?!  With the exterior planking work completed, attention could be turned to the interior and the potentially catastrophic step of removing the frames.  This actually went smoothly, but has to be approached with patience and a light hand.  The kit base was removed as well as the actual flooring should be a little lower I feel.  The frames were cut back a little more than is perhaps necessary, but this will allow flexibility as to where the floor is, and hopefully prevent them from being seen.  Practically, it also allowed the interior planking to be sanded more effectively.  The hull in this state clearly needs a light hand, but is surprisingly robust despite my fears.
 
Once an initial sanding had been completed, some light wood filler was used to fill imperfections and deal with some of the slight clinkering of the topmost walnut strips.  Once sanded back, dilute PVA was once again brushed on....yes, paranoia perhaps, but can't hurt.
 

 
Finally I was able to add an initial coat of white point to the hull to get a better idea of how this turned out (In this case Valejo 'off white' as it was all I could get from Amazon in a reasonable timeframe).  This highlighted that some finish work will be required in some areas where the eye is drawn to surface imperfections, but one thing I've learned is that the cardstock planks can be effectively sanded, probably due to the application of dilute PVA glue.  Definitely some fine tuning still needed and far from perfect, but its hard not to be pleased with the result for a first attempt.
 

Hi Folks,  have been away from the shipyard and this site for quite some time, and I've missed the friendly interaction.  Looking forward to catching up with everyone's builds soon!
 
@Martin - welcome to the neighborhood!  We got lucky and didn't lose power in the storms, hope you stayed safe.  We definitely need to connect at some point so I can pick your brains 🙂
@ Sjors - Good to hear from you old friend, its been a while!  Will check out your new model soon.
@ Stergios - the yards were rigged from bottom to top.  Not sure if that is the recommended way, but it made sense to me to do that way because the lower masts require quite a few items of rigging to be in place near the mast and it seemed that this would be harder if the lines from the top masts were getting in the way.  Maybe personal preference?
 
The cutter has finally been finished and the details of the final stages of construction are posted in my 'Jason' build log.  Figuring out where to place the cutter onboard Snake was a little bit of a challenge.  It seems inconceivable that a ship (sloop) like Snake would not have at least one boat, but there is simply no space to place one.  I could find no examples of solutions to this in practice (recognizing that other ships may well have had raised davits), and it seems somewhat logical to mount the supports on the coamings which would also be supported by the deck beams underneath.  Finally in position, its clear that even a modest 24' cutter has little room to spare.
 
With that done, now rigging can continue, hopefully some progress possible soon...
 

Hi Folks,
 
Sadly been rather absent from both the shipyard and this site for some time.  I very much hope to catch up soon on everyone else's fine builds here soon.  Time to get a little more up to date, the cutter is pretty close to completion aside from a little fettling.
 
Frames were added to the interior using strips cut from some scrap 0.5mm pear wood.  These were soaked and pre-bent in situ prior to gluing with PVA:
 

 
The frames were further reduced down to the keel former to try and get a bit more depth the boat.  To my eye, applying planking to the false deck puts the board too high, especially as there is very little room to play with considering the various structural elements still to go on. A template for the footwaling was then made up to determine the shape.  Once the placement was determined, the rising plank was added (again cut from some 0.5mm pear sheet)
 
I wanted to try and allow the footwalling to have an element of curvature which would be natural on the real boat.  A relatively straightforward way to achieve this was to apply wood strip to thin card to match the template which maintains a lot of flexibility (Straight strip was used rather than the more complicated curved planking on the plan).  Once dry, the assembly was easily glued on top of the keel former, the footwaling then follows the interior curve naturally.  
 

 
With those element in place, it was possible to add the platform under the sternsheets.  The Diana plans show these as a grating, but to my eye again the kit supplied grating is too large, so plain boards were installed instead which also appear to be used.  After the main and fore mast steps, thwarts and ringbolts I assume would be used for hoisting the boat had been added, the bow was closed in using a cover as suggested on the plan - this also helped disguise the rudimentary construction at the bow.  The rowlocks were cut, interestingly these are not symetrical between port and starboard, and one seems to sit rather awkwardly in the sternsheets.

 
The sternsheets were made up and installed, again having used a template to finalise shape, together with all the other details including mast thwarts, gunwale and knees.

 
The colour scheme follows a slightly simplified version of that shown below which seems suitably utilitarian.  Looking at this, and comparing once the black was applied, suggests to me that I made a mistake in the tapering of the clinker planking.  The black area covers both the wash strake and upper strake, and judging from these pictures it appears that these are of somewhat consistent in width, especially toward the stem.  I had tapered these proportionally as well, hoping nobody else notices...
 

Hi Folks,  have been away from the shipyard and this site for quite some time, and I've missed the friendly interaction.  Looking forward to catching up with everyone's builds soon!
 
@Martin - welcome to the neighborhood!  We got lucky and didn't lose power in the storms, hope you stayed safe.  We definitely need to connect at some point so I can pick your brains 🙂
@ Sjors - Good to hear from you old friend, its been a while!  Will check out your new model soon.
@ Stergios - the yards were rigged from bottom to top.  Not sure if that is the recommended way, but it made sense to me to do that way because the lower masts require quite a few items of rigging to be in place near the mast and it seemed that this would be harder if the lines from the top masts were getting in the way.  Maybe personal preference?
 
The cutter has finally been finished and the details of the final stages of construction are posted in my 'Jason' build log.  Figuring out where to place the cutter onboard Snake was a little bit of a challenge.  It seems inconceivable that a ship (sloop) like Snake would not have at least one boat, but there is simply no space to place one.  I could find no examples of solutions to this in practice (recognizing that other ships may well have had raised davits), and it seems somewhat logical to mount the supports on the coamings which would also be supported by the deck beams underneath.  Finally in position, its clear that even a modest 24' cutter has little room to spare.
 
With that done, now rigging can continue, hopefully some progress possible soon...
 

Hi Folks,  have been away from the shipyard and this site for quite some time, and I've missed the friendly interaction.  Looking forward to catching up with everyone's builds soon!
 
@Martin - welcome to the neighborhood!  We got lucky and didn't lose power in the storms, hope you stayed safe.  We definitely need to connect at some point so I can pick your brains 🙂
@ Sjors - Good to hear from you old friend, its been a while!  Will check out your new model soon.
@ Stergios - the yards were rigged from bottom to top.  Not sure if that is the recommended way, but it made sense to me to do that way because the lower masts require quite a few items of rigging to be in place near the mast and it seemed that this would be harder if the lines from the top masts were getting in the way.  Maybe personal preference?
 
The cutter has finally been finished and the details of the final stages of construction are posted in my 'Jason' build log.  Figuring out where to place the cutter onboard Snake was a little bit of a challenge.  It seems inconceivable that a ship (sloop) like Snake would not have at least one boat, but there is simply no space to place one.  I could find no examples of solutions to this in practice (recognizing that other ships may well have had raised davits), and it seems somewhat logical to mount the supports on the coamings which would also be supported by the deck beams underneath.  Finally in position, its clear that even a modest 24' cutter has little room to spare.
 
With that done, now rigging can continue, hopefully some progress possible soon...
 

Hi Folks,  have been away from the shipyard and this site for quite some time, and I've missed the friendly interaction.  Looking forward to catching up with everyone's builds soon!
 
@Martin - welcome to the neighborhood!  We got lucky and didn't lose power in the storms, hope you stayed safe.  We definitely need to connect at some point so I can pick your brains 🙂
@ Sjors - Good to hear from you old friend, its been a while!  Will check out your new model soon.
@ Stergios - the yards were rigged from bottom to top.  Not sure if that is the recommended way, but it made sense to me to do that way because the lower masts require quite a few items of rigging to be in place near the mast and it seemed that this would be harder if the lines from the top masts were getting in the way.  Maybe personal preference?
 
The cutter has finally been finished and the details of the final stages of construction are posted in my 'Jason' build log.  Figuring out where to place the cutter onboard Snake was a little bit of a challenge.  It seems inconceivable that a ship (sloop) like Snake would not have at least one boat, but there is simply no space to place one.  I could find no examples of solutions to this in practice (recognizing that other ships may well have had raised davits), and it seems somewhat logical to mount the supports on the coamings which would also be supported by the deck beams underneath.  Finally in position, its clear that even a modest 24' cutter has little room to spare.
 
With that done, now rigging can continue, hopefully some progress possible soon...
 

Hi Folks,
 
Sadly been rather absent from both the shipyard and this site for some time.  I very much hope to catch up soon on everyone else's fine builds here soon.  Time to get a little more up to date, the cutter is pretty close to completion aside from a little fettling.
 
Frames were added to the interior using strips cut from some scrap 0.5mm pear wood.  These were soaked and pre-bent in situ prior to gluing with PVA:
 

 
The frames were further reduced down to the keel former to try and get a bit more depth the boat.  To my eye, applying planking to the false deck puts the board too high, especially as there is very little room to play with considering the various structural elements still to go on. A template for the footwaling was then made up to determine the shape.  Once the placement was determined, the rising plank was added (again cut from some 0.5mm pear sheet)
 
I wanted to try and allow the footwalling to have an element of curvature which would be natural on the real boat.  A relatively straightforward way to achieve this was to apply wood strip to thin card to match the template which maintains a lot of flexibility (Straight strip was used rather than the more complicated curved planking on the plan).  Once dry, the assembly was easily glued on top of the keel former, the footwaling then follows the interior curve naturally.  
 

 
With those element in place, it was possible to add the platform under the sternsheets.  The Diana plans show these as a grating, but to my eye again the kit supplied grating is too large, so plain boards were installed instead which also appear to be used.  After the main and fore mast steps, thwarts and ringbolts I assume would be used for hoisting the boat had been added, the bow was closed in using a cover as suggested on the plan - this also helped disguise the rudimentary construction at the bow.  The rowlocks were cut, interestingly these are not symetrical between port and starboard, and one seems to sit rather awkwardly in the sternsheets.

 
The sternsheets were made up and installed, again having used a template to finalise shape, together with all the other details including mast thwarts, gunwale and knees.

 
The colour scheme follows a slightly simplified version of that shown below which seems suitably utilitarian.  Looking at this, and comparing once the black was applied, suggests to me that I made a mistake in the tapering of the clinker planking.  The black area covers both the wash strake and upper strake, and judging from these pictures it appears that these are of somewhat consistent in width, especially toward the stem.  I had tapered these proportionally as well, hoping nobody else notices...
 

Hi Folks,  have been away from the shipyard and this site for quite some time, and I've missed the friendly interaction.  Looking forward to catching up with everyone's builds soon!
 
@Martin - welcome to the neighborhood!  We got lucky and didn't lose power in the storms, hope you stayed safe.  We definitely need to connect at some point so I can pick your brains 🙂
@ Sjors - Good to hear from you old friend, its been a while!  Will check out your new model soon.
@ Stergios - the yards were rigged from bottom to top.  Not sure if that is the recommended way, but it made sense to me to do that way because the lower masts require quite a few items of rigging to be in place near the mast and it seemed that this would be harder if the lines from the top masts were getting in the way.  Maybe personal preference?
 
The cutter has finally been finished and the details of the final stages of construction are posted in my 'Jason' build log.  Figuring out where to place the cutter onboard Snake was a little bit of a challenge.  It seems inconceivable that a ship (sloop) like Snake would not have at least one boat, but there is simply no space to place one.  I could find no examples of solutions to this in practice (recognizing that other ships may well have had raised davits), and it seems somewhat logical to mount the supports on the coamings which would also be supported by the deck beams underneath.  Finally in position, its clear that even a modest 24' cutter has little room to spare.
 
With that done, now rigging can continue, hopefully some progress possible soon...
 

Thanks for the likes!
The depth marks are on it.
Also the butterfly at the stern.....
The Channel parts and deadeyes are also on the ship.
Till next time.
 
 
Sjors

Thanks for the likes.
Always a pleasure that you see that someone is watching.....
Done a little bit more.
Place the rudder and hinges, catheads, stern section  and bow section.
All that is seen by the pictures.
Now we go to the interior .
 
Sjors
 
 
 

I don't like the paint job at the bow so a little bit of sanding and painted again.
In my opinion it looks much better now.
Also placed the anchor hawse bolsters and the upper rail.
 
Sjors
 
 

Second planking done.
Sanded and so smooth as possible.
It was a fun job to plank this little one
I'm happy with the result.
 
Sjors
 
 

First planking is done!
On the last days of my vacation I have planked and did a lot of sanding.......
Normally I take a little sander machine called a mouse but because it is a small model I do it by hand.
The blisters are now on it 😢
Time to heal 🙂
I must say that the planking was not that easy...
Normally I have plank models that are over 1 meter long.
But I have done it.
And now tho the stern..
And then the second planking.
I only have to figure out how I clamp that second planking....
Maybe pushpins or those pins that you are using on a board?
 
 
Sjors
 
 

Even when there is a heatwave in Holland I have done some work on the Flirt.
The frame's are glued in en beveled the bow frames.
It's indeed easy to do that before it is glued to the model. (thanks for the tip Jim!)
Also placed the lower deck en the deck beams.
And there is a little door.... 🙂
I hope that we can see that when the second deck comes in place.
If not, we knows that it is there and that's the most imported thing ( I think ) 
 
Sjors
 
 
 

Yes Jim 😀
 
The first glue is on it......
Ok, it's the cradle but it is glue!
De frames are dry fit at the moment and I can trow my file's away because it fits perfect!
This will be a pleasant and amazing build!
Even Anja was surprised with what see has seen in the box.
First pictures!
 
 
 
 
 
 

Hi Folks,
 
Sadly been rather absent from both the shipyard and this site for some time.  I very much hope to catch up soon on everyone else's fine builds here soon.  Time to get a little more up to date, the cutter is pretty close to completion aside from a little fettling.
 
Frames were added to the interior using strips cut from some scrap 0.5mm pear wood.  These were soaked and pre-bent in situ prior to gluing with PVA:
 

 
The frames were further reduced down to the keel former to try and get a bit more depth the boat.  To my eye, applying planking to the false deck puts the board too high, especially as there is very little room to play with considering the various structural elements still to go on. A template for the footwaling was then made up to determine the shape.  Once the placement was determined, the rising plank was added (again cut from some 0.5mm pear sheet)
 
I wanted to try and allow the footwalling to have an element of curvature which would be natural on the real boat.  A relatively straightforward way to achieve this was to apply wood strip to thin card to match the template which maintains a lot of flexibility (Straight strip was used rather than the more complicated curved planking on the plan).  Once dry, the assembly was easily glued on top of the keel former, the footwaling then follows the interior curve naturally.  
 

 
With those element in place, it was possible to add the platform under the sternsheets.  The Diana plans show these as a grating, but to my eye again the kit supplied grating is too large, so plain boards were installed instead which also appear to be used.  After the main and fore mast steps, thwarts and ringbolts I assume would be used for hoisting the boat had been added, the bow was closed in using a cover as suggested on the plan - this also helped disguise the rudimentary construction at the bow.  The rowlocks were cut, interestingly these are not symetrical between port and starboard, and one seems to sit rather awkwardly in the sternsheets.

 
The sternsheets were made up and installed, again having used a template to finalise shape, together with all the other details including mast thwarts, gunwale and knees.

 
The colour scheme follows a slightly simplified version of that shown below which seems suitably utilitarian.  Looking at this, and comparing once the black was applied, suggests to me that I made a mistake in the tapering of the clinker planking.  The black area covers both the wash strake and upper strake, and judging from these pictures it appears that these are of somewhat consistent in width, especially toward the stem.  I had tapered these proportionally as well, hoping nobody else notices...
 

Hi Jason -- I hope you've survived the blackout and that your electricity is back on.  It's hard to work on a build in the dark, eh?
 
Cheers,
 
Martin

Hello Jason,
 
Your work is as usual...great!!!
Almost to the end?
 
Sjors

Cheers Jason.
May I ask you, finally have you worked the yards from top down or the opposite?
Thanks
 
Stergios

Such a beautiful ship!

Outstanding!  I still haven't opened the box on my planned Snake build, but I've  been following your outstanding work, and a number of others, for many months--and staring at the picture on the box lid--all the time wondering just how much confidence a crew would have to have in their captain, to set sail without a ship's boat (or three) on board, just in case.  Looking forward to seeing how you shoe-horn it in.

I bought 2 boats from CMB and mounted them on the stern quarters. worked out well.
 
Mort

The coppering is finally done! On to some more exciting things

Carronades continued. 
 
I made some .95mm rope for the guns and think I may move up to 1.10mm and see if that looks closer to scale.  The length needs to be increased also as you can see it can't haul in very far.  Fiddling with all these tiny parts makes me nervous about adding outhaul tackle.  

Made the Ships wheel and capstan as a break from the guns.  The wheel may be changed out in the future if I can find a reasonable replacement.  The parts came off the sheet all hairy and chipped but they turned out okay regardless    
 

Time for small uodate.
 
Varnished the hull and deck. Really happy with result, specially deck as it gives that slight wet look i was after. Used Admiralty matt varnish.
 
Clued cleats. Have interesting problem-kit has more cleats i can find on drawings....
Anyone with some problem?
 
Not happy with CC rooes so i have to order new ones or lend it from other kits...not sure yet. I have feeling that i must see and feel new rope and not buy it just online. Will try to find Güntteann thread here.

Also as slow pace i do the cannons-damn they are time consuming.

Woodworking i close to an end with yards and cannons left. Then its off to rigging...