Jump to content

Spanish Galleon by ships88 - Billing Boats


Recommended Posts

I got this kit on Ebay years ago. It was started and abandoned (i believe due some of the hull bulkheads upper deck pieces were broken/ missing). The model’s bulk heads, main deck and front side of the fore castle and the stern panel were put together.

 

since this Billing Boats kit was manufactured in the 1960s (i think), i figure i better do something about it before it disintegrates into dust.  

The only build log /youtube video I can find about this kid  is the one  by Frankie Day.

 

The kit doesn’t have the details of modern kit standard, however, it does have a beautiful hull lines, 4 masts and plank walkway between the forecastle and the quarter deck, which are rare subject matter combination. Can’t find much history or details about the kit or the ship it supposedly reepresents. It looks like it is just a generic representation of a Spanish galleon of the period.

 

I plan to build the model as close to the kit enclosed building drawings (two draon one sheet) as possible. Drawing 2 provides impressive number of details/clues.

The kit only provide printed gun port lids to be glued onto the finished hull. This simplificatin takes away the prowness of the galleon. I plan to add the  main gun ports operning and install half canons to remediate the short coming.

 

The broken hull bulkheads above the quarter deck are copied and glued on using the bulkhead profile from opposite of the hull.

619295D6-33CB-4C14-954F-7782850268A8.thumb.jpeg.15ecb4265f9fdc3aa29a682322f08a25.jpeg

 

The broken head was fixed using left over wood from the kit.

18C59544-9652-4A49-8DFD-EFE7F3A27B2E.jpeg

 

Lower fore-castle support beans and deck, Quarter deck support and deck were all cut from the printed sheet and installed.

28AA770F-DBCC-4655-B45B-AFB495779690.jpeg

 

 

 

6554B4B7-A600-4A69-B766-567FE87AEC19.jpeg

 

64930644-BBFD-4A9E-8377-5DB1E4348E61.jpeg

 

DD8BCA9C-21D8-4CE6-8F2F-F100ADA6C4B3.jpeg

Link to comment
Share on other sites

The head timber pieces outline were printed on a light wood board and needed to be cut out individually. Due to the characteristics of the wood, most either split or broke apart during the cutting. They were glued back together then attached to the printed head decking panel. Once attached, the head timbers became very rigid and stable.

A6D0D061-8D50-4180-B4AF-36B7E8E743B5.jpeg

 

E8DEBCF0-89FD-4054-BF96-20C4D9A15BA9.jpeg

 

The helmman's shelter was made from 5 parts cut out from the printed boar. The roof panel required soaking in water overnight, then bend over a cup with rubber bands until dried and the shape is set.

D91F9B7E-8339-4611-B2AE-EC3BF0157724.jpeg

 

4 wedges made from scrap wood were used to tie the 5 parts together. The wedges are  also cut a bit longer than the shelter height. They will server as anchor /alignement pins into the deck opening.

12B85937-4382-4B3D-98B6-BF34A4E127E7.jpeg

 

 

Cut out the back side of the forecastle & top deck and the poop deck.  Dry fit those to get an idea on how they well they fit.CECEFCF6-37EF-447C-B79C-3A08B4E8E160.jpeg

 

 

2EFD2EB7-2D09-42AC-B1E2-D44542A73326.jpeg

263E0B59-41B4-43A4-813A-C66406C4229E.jpeg
 

The last hull bulkhead is too high compared to the other two bulkheads in front of it. This need to be cut down in alignment to the others in order for the poop deck to sit properly.

F58D5395-C5CF-476B-A479-48E84BE7EB8F.jpeg

 

 

 

 

 

 

Edited by ships88
rearranaging text to match images
Link to comment
Share on other sites

According to the instruction booklet, it is 1/66 scale (a bit odd, but close enough to the 1/64 scale norm).

 

The Billing Boats catalog  brochure that was with the kit indicated a length of 73 CM (a decent size).


I photoed the other side of brochure just in case any one are interested with the available kits from Billing Boat from the time period (1960s ??)

403AA001-4C5E-47AA-96A3-6B411D0EBFB6.jpeg

F15CC22F-8DE9-49A3-B3B6-D35EC3BB1413.jpeg

 

0C6208F9-62F7-4527-8952-8E2C1E3040A4.jpeg

Edited by ships88
Link to comment
Share on other sites

Took inventory of the planks in the kit. The light colored rubbing stake planks are 3mm thick and the mahogany hull planks are 2 mm thick. They are a challenge to deal with (double plank model strips are much easier to deal with at half or less the thickness).

 

The 3mm planking turned out to be very difficult to work with. It doesn’t have any flexibility and break easily when pressure is applied. Tried soaking then bending, streaming and hot iron,, nothing seems to work. Ended up cutting notches in the plank then soak it over night, followed by fracture bending the plank.

 

88CB27BB-1DBF-4BC7-9F3F-2D2026ECBB8C.jpeg

 

A Lot of the mahogany strips were wrapped from long term storage (only few are shown in the below picture). They looked really bad.

18EA76E7-378C-4C71-A71B-AA077FDA07A9.jpeg

 

However, it turn out some were easier to fit onto the hull’s curvature by default (go figure, who knew),,,  The strips were soaked in water over night in a tall juice bottle with a clip on the end to “slowly bend it  (deluxe bending naturale by gravity) - LoL.   Final adjustment was done by cutting some small noches and fractured bending as needed.057F1CA6-41CF-479E-BB1F-9616BADE00EB.jpeg

 

I used home made planking  clamps made from folder clips (saw this hack on the internet years ago,I t works very well - no nail or hammering required) to hold the plank in place until the glue dries. 

F321707D-8CEF-4B88-A6BE-2A80FB0152F7.jpeg

 

To make a plank clamp (3 folder clips will yield 2 plank clamps) - (1) Remove the two wire handles from one of the folder clip. Take the removed wire handle and insert it sideway nto a pressed opened second file clip, then release the clip.  you now have a  finished plank clamp (easy peasy).

FF7D574C-3176-452B-914F-0A5FF7FE8869.jpeg

 

 

The rfirst hull rubbing stake and first row of hull plank installed.ADBD1C47-6016-46C8-AFEF-9EEDADB5A2CE.thumb.jpeg.d747fe70413352c15cd51d51ed0d5f35.jpeg

 

Top view with rubbering stake installed on both side.

826C1138-9CA2-47C7-9E9C-AC923C5CCB83.jpeg

 

It will take a bit of time to plank to the lower hull rubbing stake.......

 

Edited by ships88
Update and re-arrange pictures
Link to comment
Share on other sites

Single planking went a lot faster than I anticipated. Finished the 4 rows of planking under the first rubbing stake (wale) before the second rubbing stake is installed. Waiting for the 3 mm light color wood stake to get soft enough to work on.

32917ACC-414A-4D95-81A0-6B633BC0E6C3.jpeg

 

Trace out the gun port locations from the plan and made a paper template from it. I had to make an adjustment to the location of the first and last gun port as the plan side view can’t account  for the additional length from to the hull curvature. I used the hull bulkhead as the preference, separated the paper template after the first gun port snd last gun port then taped the paper template back together (see arrows in the picture of the two gap spaces added).70E39100-A0EB-46E5-9684-1A1C7048625D.jpeg

 

Taped the paper templates to the hull and Marked out the gun ports with pencil.

B0AECBDB-12C8-4E90-91FF-DF1B5E2D4412.jpeg

 

The kit instruction indicated just to glue the printed gun port cut outs to the hull. I want to cut out the gun ports and install dummy half canons and opened gun port lids. Will start that once the second rubbing stakes are installed (it would provide support for cutting the gun ports).

C1FFB1A7-548A-4AC4-87C0-7569FC6B4948.jpeg

Edited by ships88
rearranaging text to match images
Link to comment
Share on other sites

Installed the lower rubbing stake (wale).

0DA123F6-7542-4AA2-A244-BE91EFB0B757.jpeg

 

Starting to cut out the gun port by hand. Slow going cutting  the thick single plank (not as easy to cut compared to double plank method). Marked the gun ports before cutting to save the cut out piece to use as the back side of the gun port (as gun port lid follows the curvature of the hull sharpe and is not flat/ straight shape).

7EBE210B-7A1D-4F48-8EF6-287641FA8D2A.jpeg

Edited by ships88
Adding pictures
Link to comment
Share on other sites

  • 2 weeks later...

Completed cutting out the gun ports.
1203557C-3312-4E99-AC9A-157916785009.thumb.jpeg.fd3dcefe425f20a313e83d3faf056cde.jpeg

 

Made the generic shape  gun carriages from a craft stick and two coffee stirrers.

F22C117C-7540-4054-90C8-5D7E5F1F4E6B.thumb.jpeg.ea03d7ab59bb6201fe844abb57123912.jpeg

 

Going to paint those carriages with hull bulk red (I can’t find information as to what color the Spanish galleon gun carriage are normally painted with. My gut feeling is they just varnishes them).
DCD199EB-6574-4E36-A166-271B577BDB2A.thumb.jpeg.7213dae64dad9ec11fd3295bfa42b6e2.jpeg
Carriages painted. Looks ok.

 

The trim off from the coffee stirrers will do nicely for making the deck grill later.

Edited by ships88
Add pict
Link to comment
Share on other sites

472A5EC6-E03B-4967-916C-95E520F08DA7.thumb.jpeg.f09186bf24f97c383de4fe252d7908c1.jpegCut out deck pieces for the placing the gun carriages in the gun ports. As the Billing boats construction plan doesn’t have “real” gun ports installations, everything is by trial and error.


1F98DE22-A39C-4633-B574-6D5BCDEA1B49.thumb.jpeg.0793df243d209cd1b6a19eee1a6349fa.jpeg

Test shot of the gun carriage in the gun port. Looks fine, but realized a spacer will need to be added underneath the carriage (aka, to account for carriage wheel height), otherwise the deck piece will be flush with bottom of the gun port opening (awkward position).

 

4B37D1C6-604D-404B-867F-0EC68E5AC446.thumb.jpeg.f62183713a2c085a35ca32bcf79280f1.jpegspace added comparison to the original.

 

 

Link to comment
Share on other sites

Five out of the seven gun ports are located adjacent to a bulkhead. The gun carriage deck piece will be glue to those bulkheads. A piece of wood is glued perpendicular to the deck piece to serve as the joining surface.

93A4718B-98F4-477A-A0E2-CD083156BBA5.thumb.jpeg.6df006579c3a35a60ce521afdfe2d8c9.jpeg


Gun ports #3 and #6 are located in the mid point between two bulkheads and required those to be glued to the hull directly. Those deck pieces were shave off a bit on both end to confirm to the hull area they are to be positioned in. Two support wedges were added underneath to increase gluing surfaces and provide vertical supports.

21AC7898-3B86-4143-B2EE-BF91F62A0C60.thumb.jpeg.135266e53b6d5ec44c391f5465037efd.jpeg

 

Made a simple deck positioning jig to aid leveling where the deck should be placed.
F74AEC66-9B17-41E3-9CCE-D5727924A6AF.thumb.jpeg.6ea0a588ee3971af0d68d6c4df1058f9.jpeg

 

The jig’s rod is approximately where the gun would be out of the gun port.

51766184-3E41-4550-8555-0DDBD6D0390E.thumb.jpeg.fa86dd560911e5cff110f71e8819b2ed.jpeg


This is what the carriage deck looks like from underneath.

3650CC5D-3DD7-4F8A-AE16-5EA05480ED9E.thumb.jpeg.b2053ec1f451dbfb12177fcf200e4858.jpeg

 

Test fitting of the gun carriages.

71108B52-A7A7-4E80-802A-74C3A8ED248C.thumb.jpeg.f7fd6cc648a00b64909f018d6d7e42db.jpeg

 

On to the other side and repeat the same,,,,

Link to comment
Share on other sites

  • 3 weeks later...
  • 2 weeks later...
On 12/6/2021 at 2:21 AM, Backer said:

Nice work 👍


Thank you for your interest and support. Hope you are enjoying the build progress.

 

The hull planking is almost completed, 2 -3 rows left close to the keel remains.

17742E25-6EE9-44D5-B013-813840D85818.thumb.jpeg.792328531f9340f4f8c325fe89dcff86.jpeg
A lot of scrapping and sanding of the hull still need to performed.

45EE8FC2-F4AC-4A6A-85BA-27CEEB319FCC.thumb.jpeg.485920b57cb29df7fd9bc7905124e857.jpeg

All the gun carriages are installed in place.

47DF53D5-0632-4A86-A3C7-4C6E4A810E9C.thumb.jpeg.83543da49ed5e6e27f9fd3444f7b55de.jpeg

The over hang hull planking will be trimmed flush against the stern planks (after they are installed). Stern wale added (not in the Billingboats drawing)

 

 

 

Looking and planing forward to the next phase of the build and there are few decisions need to made as to what to proceed with.

 

The Billingboat’s plan for the stern area detail is very vague at best.

1509FBBC-F3C1-4217-A3B7-32A6D753C38D.thumb.jpeg.15aa1cfc43c290f43e232545e1e28059.jpeg

I think they did it intentionally to leave it up to the builder to decide as this model is a “generic Spanish galleon” of the era.

 

C80E80F5-9C7F-4004-858D-DF71298D7F41.thumb.jpeg.894774fcbffe67aabe4248528a3cd564.jpeg

The finished model galleon picture on the cover page of the written instruction booklet shows 2 lower heavy gun ports and 2 lighter gun ports at a higher deck level, and a enclosed stern wall.

 

68D937A1-B233-4B4B-BAD4-03ABA1845427.thumb.jpeg.f04c5ef3649931594a1781b9d3353615.jpeg


0783C16F-B2A1-415A-906C-B1156296E6CB.jpeg

 

I think the 2 light gun ports maybe too much (due to the width of the stern, and compared to the number of guns installed hull length wise on the same level).

 

EB6EB47E-82EF-4FA5-A8F2-B1BDC9C4750D.thumb.jpeg.c72fb965fe436ca73c36de5a8faebbe1.jpeg

The other decision is  to add individual planking, doors and hardware to the printed upper hull wall structure or just affixes them in place as is ?

24FDB1A0-F4E0-4448-A7EA-C96700E166AC.jpeg


What does everyone think ?  
Please comment with your suggestion.

 

 

Edited by ships88
Adding upload failed pictures
Link to comment
Share on other sites

Nice work.

 

Enclose?? yes

The 2 lower heavy cannons (stern chasers)?  yes  

The 2 smaller cannons? I wouldn't do this 

 

68D937A1-B233-4B4B-BAD4-03ABA1845427.thumb.jpeg.f04c5ef3649931594a1781b9d3353615.jpeg20211219_101111.thumb.jpg.11db8e566da70183b2461de1f27d99b2.jpg

Link to comment
Share on other sites

Hey Patrick, you are are doing beautiful work on the galleon.  Back in the 70’s I built two Billings kits.  I can tell you that planking and detailing as much of the printed surfaces as possible will make a big difference to your completed ship.  So I vote go for it.  👍 Hope you don’t mind me following 

 

Paul

Edited by Paul Le Wol

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

Thanks Backer and Paul for your feedbacks and inputs. They are very helpful and greatly appreciated !!

 

Working on the stern area. Starting adding the stern planks and cutting off the hull over hangs in conjunction.

6730E177-3D3C-4A0B-8BFF-FEC1582E39E3.thumb.jpeg.c4861ef9051ccb2c5fe75e12ed2b40f5.jpeg


Added two stern gun ports.

D2E97FC7-6324-4CDD-ACFB-809DA0AC1B99.thumb.jpeg.1b3ea69b42a6f820dfe9198124ffcd93.jpeg

 

Planking surrounding the gun ports completed.

537FBE4C-F37D-40E8-9584-0415460ECDAB.thumb.jpeg.605d9a8d4e43b89d7d4f6d7e29475f9f.jpeg

The gun port hinges, gun port door lifting ring and rope will be added at the end of the construction to avoid damages.

 

Wishing all a happy holiday season !!

Link to comment
Share on other sites

6B6B2F48-F4CB-4F9B-ACD5-E8FF70A8BB44.thumb.jpeg.9cdc303c3c29f82f1ac402ec45e7314f.jpeg

Installed the 2 outside stern pieces to the upper hull. Those pieces were shaved slanted to fit the hull curvature.

014EF997-AB8C-4E62-97EC-28EA20AC3FA1.thumb.jpeg.219de34626098f3eaced9332779864f7.jpeg

Scratch built the main deck ladder. It was built using my favor crap wood (two different sizes of coffee stirrers).

1F358708-A1C1-4640-A036-C552A1ECEE33.thumb.jpeg.58b342cdf2a063b937ba5dc75e002b42.jpeg

Test fitting the ladder.

 

1EA899AE-D2B5-48C6-968B-C1D1BE0B8150.thumb.jpeg.85b76cb58ed3244021c4a39b7251f9b6.jpeg

Made a 1/66 scaled sailor cut out to check for proportional correctness. All mast coats were all shaped and installed. I don’t believe they are the correct shape (should be circular shape instead of square). Oh well,,, building as indicated in the drawing. There isn’t much available information on Spanish galleon to confirm one way or the other.

B42CF85B-9CAE-4827-A3EE-B2844815E685.thumb.jpeg.36e31bf1dace509ffb011ca83c6cb71b.jpeg

Started the first planking above the deck. I had to add spaces in three places to ensure proper backing and curvature lengthwise.

Link to comment
Share on other sites

Complete 3 layers of the planking above the first hull  wale. The plan calls for 4 layers of 5mm width planking. This created a big discrepancy between reality versus the plan (there is only approximately 2 mm height left at the mid ship area (see below pictures). This height is important since there will be a highlighting light wood strip running from the head rail all the way to the stern. Need to think about which route to proceed.

76BCF9BD-05F1-4138-BE37-E0717390CBEE.thumb.jpeg.c8d21b0c30473797a21df6aad18e1f46.jpeg


9392DA32-0FB5-4B40-AC63-5CB5A4597089.thumb.jpeg.c87eab8e04b5fa65a3b95af9981ac786.jpeg

 

Made a paper template for the upper hull gun ports against the plan drawing. Added spacing for hull curvature adjustment.

7EEAF32D-CE71-4270-8847-30F104F584E5.thumb.jpeg.a960195f5dcfe9ab2d1dc946067235a9.jpegAAD3B9A8-67C0-4E7E-AA2A-184C556FB3F9.thumb.jpeg.316492d4c4d5ee1a4ce5e7424ea48b1b.jpeg

 

0A8ED8D1-DF35-4490-BA66-B717533AB7F8.thumb.jpeg.4dba52f54e71d99748354b7ff7061413.jpeg

 

2 items need a decision:

 

1. Add upper hull stern wale ? My gut feeling is not to since it will overlap over the rudder- tiler opening. This would not make any sense as wale is installed to add strength to the hull structure.

2D3047F5-B9E4-4DE6-BCCC-FCB0D6BB9D99.thumb.jpeg.1612101e9a171a1566ab8aa96b825b1f.jpeg

 

2. what plank size (width) to use for the forecastle and the poop deck planking ? Based on the scaled sailor cut out, i think it should be be the wider plank (4-5mm).
 

What does everyone think ?

759EAADD-F0F4-471C-A111-D418C54A2699.thumb.jpeg.f6ee9e121e82e18338b5791cc312fc3c.jpeg

487836C5-1F9B-4968-ADF4-EBBF79917263.jpeg

Link to comment
Share on other sites

Hey ships88, you are doing a beautiful job planking the Galleon. Would it be possible to lower the hole for the rudder/ tiller so that it is below the light colored plank (wale?) . Doesn’t look like it needs much but it may mess up your rudder.

 

Paul

Regards……..Paul 

 

Completed Builds   Glad Tidings Model Shipways. -   Nordland Boat. Billings Boats . -  HM Cutter Cheerful-1806  Syren Model Ship Company. 

 

Link to comment
Share on other sites

16 minutes ago, Paul Le Wol said:

Hey ships88, you are doing a beautiful job planking the Galleon. Would it be possible to lower the hole for the rudder/ tiller so that it is below the light colored plank (wale?) . Doesn’t look like it needs much but it may mess up your rudder.

 

Paul


Thank Paul for the suggestion.

 

There are two considerations for lowering/shorten the stern post for the rudder - tiller opening. They seems to out weight the modification justification.

 

(1) You are correct about the modification will alter the rudder profile (the fix likely will cause a lot more distortion to the over all ship profile)

 

(2) The lowered stern post /rudder opening would technically resulting in the tiller swing into the path of the two stern chase guns and their crew’s heads.

 

Link to comment
Share on other sites

10 hours ago, ships88 said:

1. Add upper hull stern wale ? My gut feeling is not to since it will overlap over the rudder- tiler opening. This would not make any sense as wale is installed to add strength to the hull structure.

 

Post 72

10 hours ago, ships88 said:

2. what plank size (width) to use for the forecastle and the poop deck planking ? Based on the scaled sailor cut out, i think it should be be the wider plank (4-5mm).
 

What does everyone think ?

post 118

 

Non-binding info 😉

 

Link to comment
Share on other sites

Thanks Backer for the build references.     Greatly appreciated! Btw. Was the Golden Hind drawings by Aeropiccola by chance ?

 

EA56BD68-0D32-4642-86C8-CB7BFAEFEEE8.thumb.jpeg.13e20e32fe577fc431d302b7bbf2f1af.jpeg

I have to first plank over the printed forecastle forward facing panel in order to proceed w the upper hull planking. By luck I found some Billing Boats mahogany planks that I brought years ago for my other Corel Hms Peregrine build. They will do nicely planking over the printed structure areas. Go figure 😁😁.

 

2107B8EA-1D58-4659-8939-77905DA046F0.thumb.jpeg.1a446fd97f031d356b5bc04eda012627.jpeg

Traced out the forecastle doors w wax paper. Shaped and created the two door frame from the thin plank. They consist of three pieces each, a header and 2 door jam studs. Those took almost 1 1/2 hrs.

 

F3FDBA8F-BC3B-4663-BCB1-7E9BFBEFD5DB.thumb.jpeg.9dee2da5ea8bfc80c67fe0b8c6952716.jpeg

Trimmed the 5mm thin planks down to 1.5 mm with strips then cut to shape and length. They took a lot of time - 2 1/2 hrs. The door hangs and handle were added afterward. Those are heavy black construction paper cut outs. The gammoning holes were cut out on the head deck and set in place.

Link to comment
Share on other sites

2 hours ago, ships88 said:

Was the Golden Hind drawings by Aeropiccola by chance ?

Difficult subject.
In my opinion, Yes


With these drawings you could build a (heavily) armed merchantman. The stern gallery and the poop deck should not be present.

 

But,

Since no one can really prove what the Golden Hind really looked like, you can also use these drawings for this purpose.
But (again) that's my opinion.

Link to comment
Share on other sites

Link to comment
Share on other sites

On 1/12/2022 at 3:35 AM, Backer said:

A newly started Aeropiccola build log. 

Interested ?


Thanks Patrick for the heads up. I will check out the build log.

 

PS. I have the Aeropiccola Golden hind kit and will build it sometime in the future.

========================
 

A few dilemmas arise after installing the 4th planking above the upper rubbing stake. It is hard to judge the exact heigh and curvature at the waist area.

 

There is a trim stake running from the head all the way to the stern. The drawing and instruction booklet did not give enough direction on the construction sequences (there seems to be a lot of inter- dependencies).  After studied the drawing numerous times, it was deducted the most logical place to start is from the head, then work backward toward the stern.

 

 

AF6EABC8-9F09-4DB5-B03F-10C0D172738D.thumb.jpeg.c23f586407985c724f7bfb38de66fd0e.jpeg

The lower trim stake for the head planking installed. The stake tills slightly upward, which will align the head planking in parallel to the forecastle silhouette angles.

 

A3C36C31-DA32-4535-B06A-728BDFD305D2.thumb.jpeg.e3ad5b9531580a90ba87b66634fc5204.jpeg

The lower head trim stake actually run into the hull upper rubbing stake. This transitions and integrates the two together.

 

AD9DB855-3C36-4F89-A870-C4B999C24279.thumb.jpeg.edc2eb83c616e0950eb2aafa2b67f9e4.jpeg

Both head trim stakes installed. The head bulwark stake had to be trim back quite a bit to allow the trim stake to lay flush against the head deck.

 

1E4AF534-111D-406B-8B4B-5F90B1FCC210.jpeg

A frontal view.


4CCC969C-7EB3-49A2-AB7E-8D37370FE278.thumb.jpeg.10b26ecff05860663a70d813d6e116da.jpeg

The head plankings installed. The over hang portions will be cut off later. Noticed the head planking tills inward. They aligned up to the forecastle’s angle profile (almost).


687EB838-5B37-4343-9089-54E5B022FB4F.thumb.jpeg.b5385e38de1782dac018c279cf1975ca.jpeg

The head planking height reduce down towards the front. Once it is trimmed down to the correct height and angle, the head rail trim will be added. This will allow the remaining trim strip height from the forecastle, to the hull waist section, all the way out back to the stern to be calculated, worked out and installed.

 

C4E63594-C014-416D-998B-D6D1F8BA39A8.thumb.jpeg.50900c3c7b43b6930af16bef8925677c.jpeg

 

Will update…

 

Edited by ships88
Edit pictures & text
Link to comment
Share on other sites

FYI. In case anyone wants to build this kit (which is very hard to find now a day), there is a complete kit w fittings (mine didn’t included this) for sale on Ebay ending in 7 hours.

 

https://www.ebay.com/itm/Spansk-Galeon-Billing-Model-Ship-Kit-Vintage-Denmark-Wooden-Spanish-Galeon-/234365391734?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l6249&mkrid=711-127632-2357-0

 

7DBF3EC0-9802-4F4A-A677-E174BDC4355C.thumb.png.42b8ae6255ce3fd7116b1eb23b4bf63e.png

Link to comment
Share on other sites

Working on the head section, this is critical in determining the rest of the upper hull structure and hull lines.

40E0F5A3-7CB4-4AEA-954F-2D4B7F7AE26E.thumb.jpeg.7ed120adb63965f7c97eb0d2cb2e5e9c.jpeg

The starboard side head hull planking trimmed down to the correct height and slope.

 

31F7C8DD-2966-498A-9A61-C3A0EB082142.thumb.jpeg.2f60fd0608f40dbc16110dcb5475464a.jpeg

The forecastle planking is being cut back to match the trimmed head hull height & angle. This adjustment in height & line will be follow thru toward the stern. Note: the tapping diminishes at the start of the quarter deck post.


4CD11ADA-DA67-4FDD-8320-E03FEFE91E27.thumb.jpeg.de5c8d59ce0088e05c62114dd255d41e.jpeg
This close up shows the height & angle differences between the trimmed Starboard and the untrimmed port-side head planking.

 

8455E086-0C14-46A5-A5D0-37F3CC072926.thumb.jpeg.b4a2875a7c0d6e84d328ff38f9764313.jpeg
An overall view of the trimmed line (Starboard side only, the port-side still need to be worked on next)

 

508DC4B2-4CA5-4828-814A-D9EE850D9CB8.thumb.jpeg.ef746bbcc1b7e4f824ef91ed0293883b.jpeg

A close up illustrating the mid ship hull line difference between the trimmed starboard side and the un-trimmed port-side height and profile.


79853C53-3E33-4005-885D-B19F21F572EA.thumb.jpeg.c78946934bd929503b28b84bc2f77427.jpeg
Test fitting of the head trim stakes. The port-side stake corner was rounded in compared to un-rounded yy side stake. Notice the frontal shape of head, it forms a trapezoid shaped.

 

405179E1-7DF7-4383-A1E8-1C7F90C76908.thumb.jpeg.ab4fb06f1d4c2e0392575d4768d043f4.jpeg
How the two head trim rails supposed to come together and finished off depended on stake #67. There is not much information about this important component other than what is shown on the drawing. It was deducted from the drawing it is 4mm thick. There are no supplied wood in the kit to account for it. It will need to be created from gluing numbers of pieces of wood together then shaped to match the drawing profile. This need to be installed first before installing the two head trim rails.

Edited by ships88
Editing text
Link to comment
Share on other sites

Working to finish the bow area in order to continue the build of the rest of the ship.

 

4159F289-F281-4C1B-9D10-B20A0EBB904B.thumb.jpeg.89d251ac070c5851f9b31261b1e906ba.jpeg

Bow frontal closed  off with planks.

8D8A9A78-27AE-4402-9ACC-07AFD8D6A34B.thumb.jpeg.4eec31ae8ef9ebaf0cac6d445937cf01.jpeg


1601CBCA-6E2B-49BA-BAFA-24636E0A0446.thumb.jpeg.022ef94df9aa49c001d6c2d6090bbee5.jpeg

Head post (#71) is a very important component determining the rest of the build. The upper bow horn(#91, I think this is used to tie up the ship to the dock in the habor ? Anyone knows more and share info on this ?) shown in the Billing boat’s drawing seems to be in the wrong spot (too high).

 

C1C3AE57-7E64-47A5-A2D9-7BB6F5D2442E.thumb.jpeg.b3fbd36c8a4e975d303aaca59a90b781.jpeg
The book “The Ship” by Bjorn Landstom has a very nice illustration of a Spanish galleon showing the upper bow horn located just below the bow bulwark rail. This location makes more sense to me than the Billingboats’ drawing location. There is NO bow figurehead. Spanish Galleon seems to be very much focused on utility and not so much with ecstatic and appearances (cravings, reliefs and decorations). 

 

398D74F8-FDE0-4E06-B2B0-DAD835C59E81.thumb.jpeg.70961e4d6c015de7bac11d7c9d9a68f8.jpeg

Traced out the bow head stud profile from the drawing to a card board. Carved out the stud using the card board template (a glued 2 piece 2mm wood stocks to build up to the required 4mm thickness). 


12D4C43C-F8C0-4182-BA3C-93E1418FDCA6.thumb.jpeg.217d1021042a73ea6d2711fb51b0c2c7.jpeg

Had to notch the head stud back 1.8mm to account for the bow frontal planking thickness (the drawing and the instruction did not accounted for this) so it can line up withe the foremost outline of the bow.


237EB7A7-C61C-4BA0-BDB1-9DFB8264AB5B.thumb.jpeg.13296b2f8388dcee3f6c423d762e3b94.jpeg
The bow upper rail was notched to fit around the bow stud.

The kit provided mid ship rail & belaying pin rail raised a question as to if an additional rail stake (from the forecastle to the stern) will lay over this. After studied the drawing, instruction booklet and the pictured model on the kit box, it is deducted it is a combo rail & belaying rack piece ( aka. There will be 3 separate rail stake segments for this elevation - forecastle to midship, midship and mid-ship to stern)


E56E537E-A5FE-497B-B029-708D4308F9E5.thumb.jpeg.a41ce937b86b3aa97deb4d47adc7dea6.jpeg
Both bow upper rails cut and installed.


A8D0DD9F-2592-4B1C-8ED0-A8BD1B77E8BA.thumb.jpeg.114d03e867bfb1a3abf77c8e1677c647.jpeg
A side view of the completed bow section.

Edited by ships88
Link to comment
Share on other sites

  • 2 weeks later...

Fixed the forecastle trims. Notches had to be cut into the strip in order to bend them to required curvature.EEAA5C6A-FA5A-4B81-831D-A3C1B5800E99.thumb.jpeg.b4e71bcd26e5c77a06f3371f63eeffa2.jpeg

 

10D74F2A-44D8-43CC-B746-C25330FE3677.thumb.jpeg.858bf102f36c90266e10235e46020c5f.jpeg

Frontal view. It became apparent that the deck need to be sealed finish before any more upper planking can proceed (access will no longer be available).

 

172148A0-2BAE-47AE-9A94-CA3FB9DA45B4.thumb.jpeg.0738b032684bc3e42413fb8d47e28736.jpeg
OMG. Tiny glue spill shows up after polyethylene is applied. The wet deck is now looks really dark. Hopefully it will lightened up a bit when completely dried.
 

Picking a sealing product turn out to be more headachy than I thought. Finish oil and bee wax option looks great, but i am not crazy about re-applying them again from time to time. Oil polyethylene and shellac is out of the question because of the fume.  Water based polyethylene seems to fit the bill. Then there is the reflective option, gloss, satin and matte finishes. since i am not making furniture, gloss was out. It was down between satin and matte - I decided on the matte finish (never used it before). Does anyone have opinions on sealing finishes that they can share ? This topic for wooden ship model is not widely covered and hard to find info on.

 

 

306A0A8F-8E2F-4E58-8CA2-18B3D7240503.thumb.jpeg.87dd9d5487a6aa0870652dcbb1a7a16e.jpeg

once the polyethylene dried, it wasn’t too bad. The finish was perfectly clear and not shiny. The main deck and the forecastle were from the same mahogany wood sheet, which is a bit darker than the other deck pieces (lighter color from a different sheet, which I liked better),,, oh well, it is real wood,, what can you do,,

DBE87937-BE4B-45A8-B072-876F98380B84.thumb.jpeg.3308bd5ddf5eecc400789b72fba2bedc.jpeg
stern over hang trimmed off. 

DD137CA5-228E-4515-A667-4314189D905C.thumb.jpeg.493ea9455e19087ffd33bc5fa5a2619b.jpeg

The hull lines are the best feature of this model ship. Just noticed the drunken sailor in the bow,, 

 

E0BAE2F2-5F01-4BE2-B19D-F5A032120924.thumb.jpeg.632e6937d3d958d730dcb31e31ea1862.jpeg

Edited by ships88
Text editing
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...