Jump to content

Recommended Posts

Posted

Thanks Rick.

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

I finished up the apron. I was hesitant to trim the parts all the way down to the line due to potential errors on my part, so stopped a bit short of that and will finish fairing them later. I did accidentally chip a piece off the top of the number 2 part and had to make a repair. You can see that in the last picture.

20240529_175638(002).thumb.jpg.32b3d58dda4e3e7b4ee4f96c7e803921.jpg

I then did a dry fit of the remaining keel parts. I noted that the keel is slightly longer than the plan but I believe that is intentional based on what I read in the instructions. I think the most critical point going forward is to make sure the upper and lower apron are in the right position.

20240529_181201.thumb.jpg.c0a8566b8dad885abb95b46f19c563c9.jpg

I mentioned this previously, I have a gap between the lower apron and the rabbet strip. I didn't sand anything there so not sure what caused it. I reduced the thickness of the plank forming the rabbet strip immediately behind the laser cut part of the rabbet strip and that did nothing. I need to figure out how to deal with this. I may remove the rabbet strip there and try again. Or maybe I should just fill the gap with some strip material. You can see the gap in the picture below.

20240529_181227.thumb.jpg.cdb2d3c6c7bee2e343ac5147bed27d3d.jpg

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

Jeff, is the lower apron a tight fit between the upper apron and the riser? If so, that'll compress the wood a little and not allow the apron to seat properly. I too had some gap on the lower apron, I gently sanded ends of the apron until the gap was smaller and used a clamp to seat fully on the rabbet strip. It didn't take too much effort to get the apron in place. Best Regards .... Rick

Posted

I think that may be the case. I will double check everything.

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

  • 2 weeks later...
Posted

I'm a little behind on this. I've had a couple medical procedures to deal with over the last two weeks so I haven't been able to do much. I'll be back on it soon.

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

  • 2 weeks later...
Posted

Trying to get back in the saddle here. Continuing on with my gap issue with the apron. I went back a couple of steps here and removed most of the forward parts of the rabbet strip and replaced it. This was because I removed some material in an attempt to get the apron to sit flush, which didn't work. I decided to replace the rabbet strips with the 1/16 strip included in the kit. I cut the first two parts to match the length of the kit parts. I soaked them and clamped in place to hold the shape and then glued them on afterwards. I also removed two of the upper parts to allow the apron to flex a bit. They may have also have been causing the lower apron to straighten a bit. At this point its nearly a perfect fit and it doesn't look like I will need any flex at all. The next challenge for me is gluing the parts on. These parts are wider than the keel so I will need to figure out how to make sure I get them properly centered.

redo.thumb.jpg.cc70fdeaa6b7912d031fd60184975544.jpg

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

  • 1 month later...
Posted

So, I'm in the process of separating all the frame parts and I'm concerned about the parts for frame Af. My Af frame parts don't seem to fit together very well. The upper timbers seem to be over sized compared to the lower frame at the joint, pictures below. This surprised me since all the others fit together almost perfectly. Did anyone else encounter this? Or is just me? I'm confident I have the right parts. 

 

frameaf3.thumb.jpg.4e407f8cf1311f05c7d0e7f298c2bbff.jpg

frameAf.thumb.jpg.0669fa64b3a6c72e6179618c70cb0308.jpg

frameaf4.thumb.jpg.3e32020580989b6f2bab8bd4b3d8bd71.jpg

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

This was Noted earlier and in the monograph.

 

Note: Those building from the laser cut parts, there are two frame parts mislabeled on sheet “M”. The two frame parts etched as “Af” are actually supposed to be parts “10a” Please correct these parts on your sheet before you begin building. Only the first 12 kits are mislabeled.   You will see two sets of AF parts with one mislabeled.  The correct AF parts are on sheet "N".

Posted
5 minutes ago, Chuck said:

This was Noted earlier and in the monograph.

 

Note: Those building from the laser cut parts, there are two frame parts mislabeled on sheet “M”. The two frame parts etched as “Af” are actually supposed to be parts “10a” Please correct these parts on your sheet before you begin building. Only the first 12 kits are mislabeled.   You will see two sets of AF parts with one mislabeled.  The correct AF parts are on sheet "N".

 

Thanks. I totally forgot about that.

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

Problem solved. I still had the old chapter one mono. Just downloaded the new one.

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

Okay, now I remember why I dismissed the note on the 10a and Af parts. When I checked my kit I saw that I had a set of correctly marked 10a's, so I assumed I had the corrected kit. I have both sets of parts, the correctly marked 10a's and the originally incorrectly marked Af's.

 

pic.thumb.jpg.3aacb4a2783c03d96b61c38e94f58328.jpg

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

Another potential issue. Hopefully I'm not just being dumb again but cant find anything in the notes about this. I can't find one piece of Cant frame part 9. I'm not able to find one of the lower parts of the frame. There are 3 parts for frame 10 though. I circled the three 10's and the one 9 in the photo. I looked everywhere for the other part 9. 

 

pic2.thumb.jpg.043164ee46a09a2ec38b91a78756abff.jpg

pic1.thumb.jpg.685fb3428bca0d03e3dfef50435cd076.jpg

 

 

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted
4 hours ago, Chuck said:

I can send another.  Just PM me your address info.  
 

 

Chuck

PM sent

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

  • 3 months later...
Posted

Hello everyone. Just wanted to let everyone know that my build is temporarily on hold. I'm the unlucky recipient of not one, but two autoimmune disorders, one of which is affecting my vision. My immune system has decided that my eyes are a foreign invader and is attacking them. As a result, I'm having vision difficulties. I have started treatment and I'm hopeful things will improve enough in a few weeks to get back to it.

Jeff

 

In progress:
Medway Longboat 1742 - Syren Ship Model Company -1/2" scale

USS Constitution - Model Shipways - Scale 1:76

HMS Granado - CAF Model - 1:48

HMS Sphinx - Vanguard

Posted

Sorry to hear about that Jeff. Hope the treatments work and your recovery is quick. 

Rusty

"So Long For Now" B) 

 

Current Builds: Speedwell

 

 

Completed Build Logs:  HMS Winchelsea 1/48   Duchess of Kingston USF Confederacy , US Brig Syren , Triton Cross Section , Bomb Vessel Cross SectionCutter CheerfulQueen Anne Barge, Medway Longboat

 

Completed Build Gallery: Brig Syren , 1870 Mississippi Riverboat , 1949 Chris-Craft 19' Runabout

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...