Archi
Members-
Posts
42 -
Joined
-
Last visited
About Archi
- Birthday 03/28/1975
Profile Information
-
Gender
Male
-
Location
Montréal
-
Interests
Shipmodeling
Recent Profile Visitors
-
Archi reacted to a post in a topic: Sloop Speedwell 1752 by Chuck - Ketch Rigged Sloop - POF - prototype build
-
Archi reacted to a post in a topic: Friedrich Wilhelm zu Pferde by Lee J H - Euromodel - 1:48
-
Archi reacted to a post in a topic: Friedrich Wilhelm zu Pferde by Lee J H - Euromodel - 1:48
-
Archi reacted to a post in a topic: Friedrich Wilhelm zu Pferde by Lee J H - Euromodel - 1:48
-
Archi reacted to a post in a topic: Saint Philippe 1693 by CRI-CRI - scale 1/72 - French warship from Lemineur monograph
-
Archi reacted to a post in a topic: Saint Philippe 1693 by CRI-CRI - scale 1/72 - French warship from Lemineur monograph
-
Archi reacted to a post in a topic: Saint Philippe 1693 by CRI-CRI - scale 1/72 - French warship from Lemineur monograph
-
Archi reacted to a post in a topic: Saint Philippe 1693 by CRI-CRI - scale 1/72 - French warship from Lemineur monograph
-
Archi reacted to a post in a topic: Saint Philippe 1693 by CRI-CRI - scale 1/72 - French warship from Lemineur monograph
-
Archi reacted to a post in a topic: Sloop Speedwell 1752 by Chuck - Ketch Rigged Sloop - POF - prototype build
-
Archi started following French 64 Gun Ship 1729 by Jeronimo , SZKUTNIK , Mycenaean War Galley by Woodrat - 1:48 - Shell first Plank on Frame and 2 others
-
mtaylor reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Canute reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Byrnes tablesaw compares with Proxxon FET tablesaw
Archi replied to kgstakes's topic in Modeling tools and Workshop Equipment
Ok, thanks ! The deviation is approximately 0.13mm. I'll act taking this fact into account. -
mtaylor reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
kgstakes reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Canute reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
ERS Rich reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Byrnes tablesaw compares with Proxxon FET tablesaw
Archi replied to kgstakes's topic in Modeling tools and Workshop Equipment
Yes, of course, I would be happy if my MicroLux® Table Saw worked as it should. Then all this fanciful Kama Sutra with clamps, screws, overlays, etc. would not be required. -
Canute reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Canute reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Canute reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
tkay11 reacted to a post in a topic: Byrnes tablesaw compares with Proxxon FET tablesaw
-
Byrnes tablesaw compares with Proxxon FET tablesaw
Archi replied to kgstakes's topic in Modeling tools and Workshop Equipment
If anyone is interested in how I dealt with the problem with the MicroLux® Table Saw: The problem of non-parallelism of the saw blade and guide grooves for Miter gage remains unsolvable. As a result, it is very difficult to use Rip Taper Gage and Sliding Table on the MicroLux® Table Saw. -
Byrnes tablesaw compares with Proxxon FET tablesaw
Archi replied to kgstakes's topic in Modeling tools and Workshop Equipment
Good photos ! Living in Ukraine more than 12 years ago, I used Proxon Table Saw FKS/E from Germany. Yes, with this saw there was no problem with parallelism, well, almost. Then I started using its clone MicroLux® Mini Tilt Arbor Table Saw. It was because of the saw blade and the guide fence are not too parallel (and not only with my exemplar, a friend has the same problem) that I had to buy Byrnes tablesaw. But something bad happened: my wife lifted my Byrnes Table Saw right behind the fence🥵. And I discovered the already skewed the saw fence😖. Now I will try to reinstall / readjust the Table Saw Fence. -
Byrnes tablesaw compares with Proxxon FET tablesaw
Archi replied to kgstakes's topic in Modeling tools and Workshop Equipment
Everything said is, of course, wonderful. But I remember that the Proxxon and its clone MicroLux® Mini Tilt Arbor Table Saw have a little problem: the saw blade and the guide fence are not too parallel. -
Excellent work ! Is it possible that the scale is closer to 1/72 ?
- 133 replies
-
Weathering wood
Archi replied to JpR62's topic in Painting, finishing and weathering products and techniques
http://forum.modelsworld.ru/topic7684start45.html -
Small comment from russian-speaker: Pear-wood, two layers of linseed oil; and then this patina (Idea Liquid Bitumen #741)
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.