Thistle17
-
Posts
1,042 -
Joined
-
Last visited
Reputation Activity
-
Thistle17 got a reaction from GrandpaPhil in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
After nearly two years in my basement and garage the hull for the PBR has gone back to the museum for final detailing. It is a mixed milepost. The venturi or cowling in the helm area was installed and glassed in for a finished look. The whole area was primed and painted. Unfortunately we used spray cans of the paint, a flat enamal. Unfortunately the spray pattern was too narrow and it was almost impossible to get a full wet coat. Quite disappointing after all the work we put into the glassing , glazing and fairing of the hull. A quick stop on the way back to the museum at an auto body shop for a quote was disappointing. The owner quoted an $800 charge!!!!!! Looks like we are going to break out some home gear to have a go at a final wet sand and repaint.
Very few deck appointments need to be completed. All cleats, armor shields, canopy frames, masts, helm, radios, scope and of course the forward gun tub and aft gun are ready to install. We just have to get past this hull paint situation. Who knew this journey would be so troubled.
Joe
-
Thistle17 got a reaction from KeithAug in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
Now that the model has been moved back to the museum it is receiving the attention it deserves. The director of the museum supported the effort by purchasing an airless paint gun with adjustable nozzle patterns. Since the hull had more than enough time to cure the oil thinner" based paint it was decided to spray the hull with latex. I must say it was a hugh improvement over the earlier attempt. Chuck, the director was able to keep a wet coat and as noted the results were quite pleasing.
After months, no years, of a bare hull we could not resist dry fitting some of the major components to give ourselves a boost to "bring the project home". Shown in the accompanying photos we temporarily placed the pilot console and the armament sheilds in the helm area. And of course we had to witness the forward gun tub resting in the hull. Also note the venturi is now in place and some of the helm area braces (not shown) have been added. It is amazing how even the little things contribute to the character of the project.
Standby as we will be installing signal and radar masts, attennas, aft gun platform, canopy framing and all the other previously mentioned elements.
Joe
-
Thistle17 got a reaction from Jack12477 in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
Now that the model has been moved back to the museum it is receiving the attention it deserves. The director of the museum supported the effort by purchasing an airless paint gun with adjustable nozzle patterns. Since the hull had more than enough time to cure the oil thinner" based paint it was decided to spray the hull with latex. I must say it was a hugh improvement over the earlier attempt. Chuck, the director was able to keep a wet coat and as noted the results were quite pleasing.
After months, no years, of a bare hull we could not resist dry fitting some of the major components to give ourselves a boost to "bring the project home". Shown in the accompanying photos we temporarily placed the pilot console and the armament sheilds in the helm area. And of course we had to witness the forward gun tub resting in the hull. Also note the venturi is now in place and some of the helm area braces (not shown) have been added. It is amazing how even the little things contribute to the character of the project.
Standby as we will be installing signal and radar masts, attennas, aft gun platform, canopy framing and all the other previously mentioned elements.
Joe
-
Thistle17 got a reaction from GrandpaPhil in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
Now that the model has been moved back to the museum it is receiving the attention it deserves. The director of the museum supported the effort by purchasing an airless paint gun with adjustable nozzle patterns. Since the hull had more than enough time to cure the oil thinner" based paint it was decided to spray the hull with latex. I must say it was a hugh improvement over the earlier attempt. Chuck, the director was able to keep a wet coat and as noted the results were quite pleasing.
After months, no years, of a bare hull we could not resist dry fitting some of the major components to give ourselves a boost to "bring the project home". Shown in the accompanying photos we temporarily placed the pilot console and the armament sheilds in the helm area. And of course we had to witness the forward gun tub resting in the hull. Also note the venturi is now in place and some of the helm area braces (not shown) have been added. It is amazing how even the little things contribute to the character of the project.
Standby as we will be installing signal and radar masts, attennas, aft gun platform, canopy framing and all the other previously mentioned elements.
Joe
-
Thistle17 got a reaction from Roger Pellett in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
Now that the model has been moved back to the museum it is receiving the attention it deserves. The director of the museum supported the effort by purchasing an airless paint gun with adjustable nozzle patterns. Since the hull had more than enough time to cure the oil thinner" based paint it was decided to spray the hull with latex. I must say it was a hugh improvement over the earlier attempt. Chuck, the director was able to keep a wet coat and as noted the results were quite pleasing.
After months, no years, of a bare hull we could not resist dry fitting some of the major components to give ourselves a boost to "bring the project home". Shown in the accompanying photos we temporarily placed the pilot console and the armament sheilds in the helm area. And of course we had to witness the forward gun tub resting in the hull. Also note the venturi is now in place and some of the helm area braces (not shown) have been added. It is amazing how even the little things contribute to the character of the project.
Standby as we will be installing signal and radar masts, attennas, aft gun platform, canopy framing and all the other previously mentioned elements.
Joe
-
Thistle17 got a reaction from Canute in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
Now that the model has been moved back to the museum it is receiving the attention it deserves. The director of the museum supported the effort by purchasing an airless paint gun with adjustable nozzle patterns. Since the hull had more than enough time to cure the oil thinner" based paint it was decided to spray the hull with latex. I must say it was a hugh improvement over the earlier attempt. Chuck, the director was able to keep a wet coat and as noted the results were quite pleasing.
After months, no years, of a bare hull we could not resist dry fitting some of the major components to give ourselves a boost to "bring the project home". Shown in the accompanying photos we temporarily placed the pilot console and the armament sheilds in the helm area. And of course we had to witness the forward gun tub resting in the hull. Also note the venturi is now in place and some of the helm area braces (not shown) have been added. It is amazing how even the little things contribute to the character of the project.
Standby as we will be installing signal and radar masts, attennas, aft gun platform, canopy framing and all the other previously mentioned elements.
Joe
-
Thistle17 got a reaction from FrankWouts in HMS Winchelsea 1764 by Rustyj - FINISHED - 1:48
Such a rich, warm effect achieved with the wood choice and color added.
Joe
-
Thistle17 got a reaction from mtaylor in Pequot 1908 by svein erik - FINISHED - 1/48 scale - Coast Guard Cutter
A masterwork! I was fascinated with the hull construction. The "plating" was just beautiful. Such an interesting subject as well.
Joe
-
Thistle17 got a reaction from FrankWouts in HMS Winchelsea by rafine 1/48
I have tracked your work since I discovered this site some years ago. Your work is always inspiring.
As the saying goes "love like youth is wasted on the young". One might draw a comparison to ship modeling and modelers. General health including sight, dexterity and the like, most needed for modeling alude us as we age and when we are most apt to be into this pursuit!
Wishing you a speedy recovery. Be patient with it.
Joe
-
.jpg.d84ec4dad1d7791e855dca06210ab6f3.thumb.jpg.f45209242e851d4409eca1a09293165b.jpg)
Thistle17 got a reaction from hollowneck in HMS Winchelsea by rafine 1/48
I have tracked your work since I discovered this site some years ago. Your work is always inspiring.
As the saying goes "love like youth is wasted on the young". One might draw a comparison to ship modeling and modelers. General health including sight, dexterity and the like, most needed for modeling alude us as we age and when we are most apt to be into this pursuit!
Wishing you a speedy recovery. Be patient with it.
Joe
-
Thistle17 got a reaction from yvesvidal in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
We cannot account for the lost days and time during the Covid isolation as I am sure you will agree. As far as the PBR is concerned we have been working on her albeit haltingly. Here is a recent photo of the model coming together in April for a dry fit of masts, gun turret, helm (not shown) and rear 50 caliber tripod mount gun. The hull still needs some refining but we are getting close to a full paint job of the basic unit. Lots of fittings and details to add but we are getting there.
Joe
-
Thistle17 got a reaction from mtaylor in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
After nearly two years in my basement and garage the hull for the PBR has gone back to the museum for final detailing. It is a mixed milepost. The venturi or cowling in the helm area was installed and glassed in for a finished look. The whole area was primed and painted. Unfortunately we used spray cans of the paint, a flat enamal. Unfortunately the spray pattern was too narrow and it was almost impossible to get a full wet coat. Quite disappointing after all the work we put into the glassing , glazing and fairing of the hull. A quick stop on the way back to the museum at an auto body shop for a quote was disappointing. The owner quoted an $800 charge!!!!!! Looks like we are going to break out some home gear to have a go at a final wet sand and repaint.
Very few deck appointments need to be completed. All cleats, armor shields, canopy frames, masts, helm, radios, scope and of course the forward gun tub and aft gun are ready to install. We just have to get past this hull paint situation. Who knew this journey would be so troubled.
Joe
-
Thistle17 got a reaction from Canute in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
After nearly two years in my basement and garage the hull for the PBR has gone back to the museum for final detailing. It is a mixed milepost. The venturi or cowling in the helm area was installed and glassed in for a finished look. The whole area was primed and painted. Unfortunately we used spray cans of the paint, a flat enamal. Unfortunately the spray pattern was too narrow and it was almost impossible to get a full wet coat. Quite disappointing after all the work we put into the glassing , glazing and fairing of the hull. A quick stop on the way back to the museum at an auto body shop for a quote was disappointing. The owner quoted an $800 charge!!!!!! Looks like we are going to break out some home gear to have a go at a final wet sand and repaint.
Very few deck appointments need to be completed. All cleats, armor shields, canopy frames, masts, helm, radios, scope and of course the forward gun tub and aft gun are ready to install. We just have to get past this hull paint situation. Who knew this journey would be so troubled.
Joe
-
Thistle17 got a reaction from Jack12477 in PBR Mark 1 River Patrol Boat by Thistle17 - FINISHED - Scale 1:6 - Model Shipwright Guild WNY
After nearly two years in my basement and garage the hull for the PBR has gone back to the museum for final detailing. It is a mixed milepost. The venturi or cowling in the helm area was installed and glassed in for a finished look. The whole area was primed and painted. Unfortunately we used spray cans of the paint, a flat enamal. Unfortunately the spray pattern was too narrow and it was almost impossible to get a full wet coat. Quite disappointing after all the work we put into the glassing , glazing and fairing of the hull. A quick stop on the way back to the museum at an auto body shop for a quote was disappointing. The owner quoted an $800 charge!!!!!! Looks like we are going to break out some home gear to have a go at a final wet sand and repaint.
Very few deck appointments need to be completed. All cleats, armor shields, canopy frames, masts, helm, radios, scope and of course the forward gun tub and aft gun are ready to install. We just have to get past this hull paint situation. Who knew this journey would be so troubled.
Joe
-
Thistle17 got a reaction from Rustyj in HMS Winchelsea 1764 by Rustyj - FINISHED - 1:48
Such a rich, warm effect achieved with the wood choice and color added.
Joe
-
Thistle17 got a reaction from hollowneck in HMS Winchelsea 1764 by glbarlow - 1:48
As they say Glenn copying or following another's work is well deserved flattery. Your work is in my list of one's to follow!
Joe
-
Thistle17 got a reaction from Freebird in HMS Winchelsea - FINISHED - 1764 - by Chuck (1/4" scale)
Thinking back to when such a technique was not available one has to admire those builders of "yesterdays"models. You continue to refine laser fabrication each time you advance this build. Your techniques put this project within reach of so many more of us than was possible in these past few years. I hope everyone appreciates your engineering efforts.
Joe
-
Thistle17 got a reaction from FrankWouts in HMS Winchelsea 1764 by glbarlow - 1:48
Beautiful execution Glen! Inspirational!
Joe
-
Thistle17 got a reaction from Rustyj in HMS Winchelsea 1764 by glbarlow - 1:48
As they say Glenn copying or following another's work is well deserved flattery. Your work is in my list of one's to follow!
Joe
-
Thistle17 got a reaction from FrankWouts in HMS Winchelsea 1764 by glbarlow - 1:48
As they say Glenn copying or following another's work is well deserved flattery. Your work is in my list of one's to follow!
Joe
-
Thistle17 got a reaction from Dave_E in HMS Winchelsea 1764 by glbarlow - 1:48
As they say Glenn copying or following another's work is well deserved flattery. Your work is in my list of one's to follow!
Joe
-
Thistle17 got a reaction from billocrates in NAIAD 1797 by Bitao - 1:60
I should not be surprised by your response but I am. The demands you place on yourself in model building run deep. It would be a pleasure to meet you were it possible. I say that as I am working on a "restoration" of a model that is extremely well done, yet not of your complexity. The modeler is unknown yet the work deserves my efforts to bring it back to life. Everytime I work on it I can hear myself saying "Who was this person?". Sadly I will never know. It is the same thing I say when I look at a painting masterpiece such as Caravaggio or Vermeer work. I will let you read into that.
Joe
-
Thistle17 got a reaction from billocrates in NAIAD 1797 by Bitao - 1:60
You deserve all the continued praise for your work is no surprise. Bitao it did get me thinking about the long term and your legacy. Have you thought about what to do with your works? Where will they go/ certainly to somewhere where they will be cherised.
Joe
-
Thistle17 got a reaction from billocrates in NAIAD 1797 by Bitao - 1:60
Master works bitao! Your joinery is superb. You missed your calling as you should have been a master shipwright. Maybe in your next life????
Joe
-
Thistle17 got a reaction from Saburo in NAIAD 1797 by Bitao - 1:60
An imaginative variation of the machinist 'V" block where the hold down always seems to be in the way. Great design of the clamps. It seems easily transferable to a wooden version for those not into machining non ferrous material.
Joe
Our Emblem ®
