Jump to content
New Publication - Ship Modeler's Handbook - They're back in stock! Thank you for your patience. ×

flying_dutchman2

Members
 View Profile  See their activity

  • Posts

    1,731

  • Joined

  • Last visited

 Content Type 

Everything posted by flying_dutchman2

  1. flying_dutchman2
    Canon holes have been filled out and painted on the inside with medium cadmium red which is the same color as the inside of the railing. Still need to do the final coat of the cadmium red and the outside in cobalt blue. Transom is cut out and painted as well. Inside is Prussian blue and outside is cobalt blue. Created a carving peg board. Took a piece of pine board and drilled 1/4" holes every 1/2" and every 1" all over the board. Took birch and left over cherry dowels and cut them in 3 and 4 cm lengths. The piece that is in between the pegs is the River God carving. I cut it out with a hand jigsaw and added pencil marks which will be carved out and painted yellow ochre. The pieces on the blue cover still need to be carved. The red is cherry and the white is maple.
  2. flying_dutchman2
    So instead of the carving the canon wreaths, I am replacing those with port hole covers. Will file them down somewhat, paint them yellow ochre and, voila, done. This Wednesday I will meet a member from the north west Indiana woodworkers Association (a club I joined recently) and go through his stash of wood cut offs. There is a lot of basswood and balsa that I know of. Also, brass, copper, stainless steel, aluminum and other metals in strips and wire in various thicknesses. At the last club meeting I mentioned that I can use any cut offs that anyone wants to part with. After the meeting several members came to me and asked if I can use cherry, ash, alder and apple. I said yes, and I will have it in the December meeting.
  3. flying_dutchman2
    Hans, Thank you for the picture. It is a better one than I saw on Google. The gray part was new to me. I will go to your website and check it out. Marcus
  4. flying_dutchman2
    I went to Google.nl and searched for statenjacht Utrecht and came up with all types of pictures. Areas that need to be painted a total different color. Also found additional items that are not included in the plans. As I am going to model it like the replica, I am going to omit the canons. Marcus
  5. flying_dutchman2
    Question for the Dutch members who have seen the replica of the Utrecht more than once. The lion is holding a shield with his front paws, what are the two colors? Top color and the bottom color. Nowhere in the Hoving book is their a picture depicting this and I have scoured the Net of Utrecht images. This would be much appreciated. Thanks Marcus
  6. flying_dutchman2
    Yesterday I cut out almost all of the carvings on the scrollsaw and today penciled in some simple lines that follow the curves. I am doing some of the examples of the plans but will omit the intricate stuff. Keeping it simple. Be creative in my carvings. Made a lot of diplicates as well. Marcus
  7. flying_dutchman2
    Thanks Hans, that is an excellent idea Marcus
  8. flying_dutchman2
    Piet, Patrick, Hans, and cog, thank you for your encouraging words. I can put a long post together of all the mistakes I have made, but this one is a "Big One". If I am off by a few mm than I can adjust it but if it is more than 5 mm, and I try to adjust it, it won't look right and at the scale of 1-50 cm it gets out of whack fast. The problem: The bottom of the Stern windows need to match up with the side windows and they didn't. The bottom of the side windows compared to the bottom of the Stern windows are 5 mm to high. So I am leaving the side windows as is (instead of redoing that as well) and raising the area above the Stern windows by 5 mm. I don't want to widen the 45 degree area where the top of the rudder is. That looks weird (I tried that as well). The carvings will be as is and where there are gaps, I will add filler pieces. The carvings are going to be cherry. This wood carves nice. I am also keeping it simple. Non of the frilly stuff. I have broken many pieces by putting in too much detail and the piece I kept simple, looks good. All of these pieces will be painted Yellow Ochre. Below is a piece that goes on the top of the Stern. Still needs to be sanded. Marcus
  9. flying_dutchman2
    Worked on the Stern and noticed that I was off by lots of mm. Tried to adjust that but it only got worse. So I trashed the Stern but saved the window frames. I spent a lot of time making them. So tomorrow I will re-cut the Stern, make windows and fit the frames. Marcus
  10. flying_dutchman2
    Glued the two sides and the front of the pavilion together. Most of the pavilion wall areas will be covered with carvings Paint color: Pavilion outside is cobalt blue. Inside is Prussian blue. Pavilion front is Prussian blue and the molding is cobalt blue. All window are titanium white. The window frames are yellow ochre. Inside of the railing is cadmium red, medium. Marcus
  11. flying_dutchman2
    Discarded the walnut and created the railing with poplar strips. Glued in the deck beams, redrilled the holes in the hull and jammed toothpicks with a bit of glue in them. Laminated 2 strips (1x6mm) of poplar together and glued on the outside of the toothpicks and 1 of the same strip on the inside of the toothpicks. Added scrap wood to fill in the gaps between the strips. It will be finished off with 2 x 2mm strips laminated on top totalling 8mm in height. Cut out the strips on the inside including the toothpicks where the pavilion sides are glued in. Out of 3mm thick balsa cut out the pavilion sides and laminated 1/64" veneer to the front of it. Dry fitted the sides and the windows and the front. My overall width of the boat is 6mm too narrow, so I had to sand down the sides of the pavilion front. Furthermore, my Stern piece is going to be a little higher than what the plans show. Now that this is all done, I will be working on the deck. The pavilion floor will be a couple of mm higher than the deck as the tiller goes between it. This is what the plans show. Marcus
  12. flying_dutchman2
    I was going to use the walnut as it is the correct width (6mm ) plus a 2mm square dowel to make a total of 8 mm high railing. I am now going to use 4 x 2mm strips and veneer it on both sides. It will be painted Prussian blue. I can also pin down the walnut with the smallest insect pins I have and glue a 2 x 2mm strip on top of it. I have so much walnut in my possession. Marcus
  13. flying_dutchman2
    I had to rethink the railing. First time I soaked 2x6mm walnut and tried to bend it along the curve of the boat and ended up with a clamp forrest (Cog's definition). After the planks were dry they didn't keep their curve. So this morning pulled out the saw and cut 2x2mm strips from Poplar _ Tulip tree, to be exact. Made a lot of these as I am bound to break a few. For the Utrecht I have been using a lot of Poplar. It has good bending characteristics, especially for bluff bows and it is cheap. Marcus
  14. flying_dutchman2
    Beautiful work. Another bluff bow ship, just like my Utrecht yacht. I see that you did your planking the way I did it. Planking a bluff bow can be a challenge. Marcus
  15. flying_dutchman2
    It is starting to look like a boat. Glued the stem, keel and post. Also drilled two holes for the stand. I will be using two pieces of brass tubing of equal length. I may cover the tubing with wood. Marcus
  16. flying_dutchman2
    Thanks Carl.
  17. flying_dutchman2
    Finished the rudder and the post. Used cherry wood for both items and the brass pintels were attached with stainless steel insect pins cut to 3 mm in length. Glued the pintels with CA on the rudder and post, once dry, used a drill bit #79 (0.0145") to drill holes through the brass and partially through the wood. Then pressed the pins in. The pins are strong and they are great for this. Marcus
  18. flying_dutchman2
    Thank you for the compliment , Patrick (this coming from the king of itty-bitty scale models). Marcus
  19. flying_dutchman2
    I am pulling up a chair as well. This looks like a great kit to build. Dutch kit made by Dutch company. You know it will be accurate. Hans (one of the owners) has built a fantastic model the Batavia. Marcus
  20. flying_dutchman2
    Wow, looks really good and like the details as well Marcus
  21. flying_dutchman2
    Hi. I have been procrastinating about this but it is time that I start this. The yacht Utrecht has many carvings. I have practiced some simple items from wood but with the many mistakes I have made I am no longer using wood. Purchased 1 lbs. of Super Sculpey and I have the following questions. Is it possible that I make, say a rectangle piece of clay 1/4" by 2" by 1", bake that, and after it is cooled, carve it? As Chuck mentioned in an article in Ships and Scale is that you can bake a piece and keep adding to it. Does the new clay adhere to the baked clay just like that or how is it done? Thanks Marcus
  22. flying_dutchman2
    Finished 2nd layer of planking. Still needs to be sanded. The blue tape is to protect the planking on the back of the keel Also a dry set up of how the pavilion windows are placed. Here I use balsa as a template. Marcus
  23. flying_dutchman2
    Thanks Carl. Finished the second layer of planking. I am pretty satisfied with it. Planking flows nicely towards the back and the bluff bow looks good as well. The will sand it tomorrow, and upload some pictures. Still haven't done any serious carving. I keep procrastinating on this, but will eventually have to do it. Marcus
  24. flying_dutchman2
    Pavilion windows: This was a difficult project. I used sculpey clay to set the window frames in, aligning the sides. After lots of trail and error, redoing the clay and measuring the length and width of all three frames together, I was able to get it close. Used bits of clay on the top as well to keep it aligned. Used white glue on the inside. Once dried and removed from the clay I can sand them a bit and touch up the paint. I have seen other models on other sites of the way the windows are positioned and they are all straight where as I have them on an angle and slightly bend forward to follow the contour of the pavilion wall. Maybe overkill. Marcus
  25. flying_dutchman2
    Put the pavilion windows together, the frames are titanium white and the frames are yellow ochre. Besides a few minute paint touch ups they are done. In Dutch this is what is called 'priegel werk' (sp.) Marcus

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...