AnobiumPunctatum

In the meantime, the planking is completed on the port side.
The hull is not sanded, as can be seen.

 

 

Build log part 11
 
 
some progress on building the hull....
 
Nils
 
 

 
this is no convertion to a viking longboat, but temporary protection to the prolonged bowpost until the upper bow bulwark is ready for attaching
 
 

 
my wife asks me this morning, if I`m sure the ship is not much too narrow...
All the overstanding frame hights have been cut off
 
 

 
between the second and the third rail (stern) I need enough place for attaching the decoration and the name, and homeport.
For providing adequate space for the portholes around the poop and perhaps some "eyebrows" over the portholes, I had to increase the hight of this (round the stern) plank accordingly as well as a good transition of the sheer in foreward direction
 
 

 
these are preliminary deck-stringers, for dry fit. There will be a pit right down to the lower deck, just behind the later forecastle bulwark
 
 

 
 
 

Karl, Mick, Cog and Greg, thanks for looking in.
Slowly but surely, the planking is completed.
I hope that it is the way I imagine it.

 

Another small update the last before a vacation break.
Alexandru
 

Hello friends.
 
Assembly of the deck transom and filling transoms on the fashion  piece.
 
 
Karl  
 
 
 
T e i l   1

Welcome on bord, Antony
 
The completion of the hull of my control model in the region behind the last frames has attracted much longer than expected.
When planning the last phase of the construction I realized that the body plan of the original drawing and therefore my reconstruction at the top of the last two frames is too narrow. So back to the drawing board and the frames 19 and 20 newly constructed. The hull at frames 20 is now about 1 mm wider in the region of maximum breath than originally. With the help of several buttok lines and the new water lines I have also redesigned the transoms

I haven't add all changes on the test hull, so you can see in the pictures the not entirely harmonious course of the lines.





The first step of my little project -the reconstruction of the lines- is complete.
In between, I have asked myself several times whether the construction of the half-model was even necessary. After the problems in the reconstruction of the transoms and fashion pieces, that define the shape of the stern, have identified, the construction of the test model was more than worth. I am happy to have the mistakes now and not found during the construction of the POF model.

In the next few weeks I'll construct keel, frames and all other components that are needed to build the hull. In autumn I like to start the construction of the POF model. Until then, one last picture which shows the side view of the test hull.
 

The frameing looks really impressive, very nice work

The transoms can not be derived directly from my reconstruction of the body plan.In the half breath plan of the orioginal drawing the form of each timber is indeed located, but does not fit properly on the corrected design. Before starting for the next step I have taken these lines and adjust them so that they match up with my design and also with the position of transoms in Sheer plan.
Subsequently the transoms were transferred to 3mm plywood, sawn and glued on the control model. I 've filles the gaps as usual with poplar plywood. After sanding the area looks like in the following pictures:
 

 

 

 
 

Thanks Johann, druxey, Mike and Nils for your nice comments and all others for the Likes
 
Next I've installed all bulkheads until frame 20 and the filling pieces.
 

 
Then my favourite pastime - sanding
 

 

With the build of my control model I started at the end of March.

The edges of all frames I've colored black. This will be later a great help by sandig the hull.
The glued surface of the cant frames is very small, so I've glued first plywood stripes on the center board.
To get the correct alignment the colored 5' marks on the frames and the center board are a great help.
 

First half of frame 0
 
Six frames have been installed.
 

 
At this time I've started to glue the filling pieces of polar plywood between the frames. I've used a chess board pattern to avoid the distortion of the frames.


 
Until the mid of April I've installed all frames and filling pieces from the center to the stem on the stem.
The next two pictures show the result of the work. It's looking very horrible
 

 

Then I've started sanding the hull. I've used 60 grid until 120 grid sandpaper for the process. After around one week - I can only work on my model in the evening or at the weekends- I've finished the front half of my control model.
I am very happy with the result
 

 

 

 
To check the curves I use 1mm thick stripes of maple. The found differences are very small. So I think that my reconstruction will work for the checked range.
 

 

 

 

 

Mark, thanks for the input and hope I'm not seeming argumentative. I'm going to keep thinking it over. The obsessive part of me is actually considering building a false bow with similar configuration to test out how each approach would actually look. In the meantime, I can let it simmer while I work on the decking.
 
Speaking of which, here's another update after the weekend's work:
 
While I think about planking, I've worked on filling in structure. The deck was mildly cambered, with deck beams resting on one longitudinal bulkhead running along the keelson. So the first step was to figure out how high I wanted this bulkhead (and thus the camber), and how to keep it fairly consistent along the run of the hull, rising with the sheer of the stem and stern from the flat central portion of the hull. I wanted the camber to last all the way to the stern, but naturally peter out into a smooth surface at the stempost. This appears to be accurate based on my sources.
 
I accomplished this the way I do many projects, by careful dead reckoning. I figured out the proper bulkhead height at the center of the hull, by test-fitting various stanchion lengths with deck beams resting on top until I got something that looked right. Then I cut a stringer the length of the hull, to act as the top of the bulkhead, and began gluing it onto stanchions of equal height along the flat center portion of the hull, letting both ends float free. Once that was dry, I began carefully cutting individual stanchions to increasing lengths, inserting them under the stringer one by one while test-fitting deck beams to ensure a smooth curve. The photos above show the stern end completed; if you look carefully down the hull, you can see the bow end still floating free. Then I did the same for the bow. This center bulkhead was finished with planking on the real Bertrand, dividing the hull into separate halves, but I'm omitting that for viewing clarity.
 

 
At some point I decided I was getting tired of having the hull loose on my work bench, so spot-glued a thick beam to the bottom of the hull, where my clamp can get a good grip. Big improvement; I can now swivel the hull to any orientation I need.
 

 
With the longitudinal bulkhead properly finished, and all support stanchions glued in, I began attaching deck beams, a repetitive but fairly easy process. Below is the final result, after a lot of sanding to produce smooth curves all the way around. Interestingly, the guards (which I intended to be level) ended up a bit gull-winged in places, angling inward slightly toward the deck camber. This annoyed me, until I happened to read in one of my sources that some period boats actually did have inward-sloping guards, though it's believed Bertrand didn't. It's barely noticeable, and at least it's authentic to the period if not the exact prototype.
 

 
After I was happy with the deck beams, I moved on to preparing a few more details. I framed in the five hatches (one at left stern, and two pairs centered about 40' from the stern and just aft of the bow). I intend to leave all these open. 
 

 
I have now reached the point that I have to make a decision on how to finish the model, no more waffling. I am sticking with my original goal, despite various forays into conjecture, of finishing the port side completely, and leaving the starboard side as open-framed as possible to allow views of the internal structure. I want to be able to photograph the model from certain angles and have it look realistically complete, but have in-person viewers be able to turn it around and look inside. Thus I will have to add much, but not all, of the decking (I may use piles of cargo to hide missing decking for photography in some places).
 
With this in mind, I added one more set of details. The deck beams and guards, as installed so far, are actually half as numerous as on the real boat. I decided to leave the deck beams as-is to facilitate interior views, but to fill in the guard supports on the starboard side for more realism. This accounts for the different you may already have noticed, but which is very clear in this overhead photo. Looking closely, you can also see the framed-in deck hatches, and the doubled-up deck beams which support the boiler, about 1/3 of the length from the bow.
 

 
The boat is nearly read for some decking, and is ready for planking on the port side once I decide how I want to do it. In the meantime, here's Alison Krauss & Union Station with the feelings of all Missouri after the last two months: "Rain, Please Go Away"!
 

Time to work on the pumps and cistern.  I had previously rough-shaped the hexagonal pump tubes and left them long for final shaping later.  There are four tubes that terminate in the cistern and in front of them are the two hand pumps.  Each of the tubes was cut to length based on the drawings in TFFM.  They were bored for insertion of the pistons later.  They have been dry-fit into their openings in the deck and main mast partners.  The nozzles for the hand pumps point 45o aft.  I did not have any metal supplies with me this week so they will be finished and permanently installed later.
 

 

 

 

 
The cisterns are relatively straightforward.  They are essentially boxes with two vertical side and two canted sides sitting on legs which are wider in the front than in the back.  There is a slot outboard for insertion of the pump dale and holes in the bottom for the pump tubes.  The outboard feet are taller than the inboard ones to compensate for the thickness of the mast partner.
 

 

 
There is a removable cowling which covers the pump wheel and chain assembly.  I have decided to make the port cowling and leave the starboard cistern uncovered to demonstrate the wheel and chain.  They still need to be detailed and I have not decided whether to show the pump dale.  Where would it be stored when not in use?
 

 

 
The cisterns are temporarily set in place behind the main mast.  There are a lot of structures in a very small space. 
 

 

 

 

Many thanks Patrick and Mick,
and all the "like this" button activators...
 
 
Patrick,
Thanks for your appreciation, I took her off the board this afternoon and was delighted of the work so far, a straight symetric and light hull like it should be. All the overstanding frame hights will be removed (cut off) and the upper deck stringers put on. The slot places are integrated alrteady when I cut the frames
I am including some pics of this milestone moment....
 
 
Mick,
Thanks for your words ,..
For plating I shall use self-adhesive aluminium foil stripes which will be ponced from the rear side to resemble the riveting
Before the plating comes on, there is still some filler application work to be done, and several semi-round rails must be attached to the ouside hull skin.
 
 
 

 
removed from the board and put on the upper end-cap plank 180° around the stern.
Stb aft view...
 
 

 
stb front view
 
 

 
view into the aft ship hull. The outcuts for the deck stringers can be seen here
 
 

 
 
 

 
the "deck-beam" upper lnes are pre cut, so only the outer sides of the frames need to be cut. In this way the decks will have a positive curvature in width direction
 
 

 
one of the three lock-nut devices for the stand`s pedestal-spindles (through the keel and anchored in the "backbone" )
   
 

 
removing some old hardened glue drops out of the hull

Really nice hull, Nils

Fish Davit
 
The Fish Davit is used when pulling up the Anchor. The associated tackle literally is used to "fish" the anchor around the flukes and then haul the crown end up ready for stowing.
 
The davit is tapered by 3 scale inches on all four sides. A stop is cut into each end :
 

 

 
A handrope is fitted to enable the davit to be manhandled into position. Nine eyestrops hold the two ropes together by passing through the centre of the davit. These were a whole lot of fun to fit, as they have an eye in one end and the other end doubles back into the hole. A drop of PVA glue holds the doubled end in place :
 

 

 
 Danny

Welcome on bord, Antony
 
The completion of the hull of my control model in the region behind the last frames has attracted much longer than expected.
When planning the last phase of the construction I realized that the body plan of the original drawing and therefore my reconstruction at the top of the last two frames is too narrow. So back to the drawing board and the frames 19 and 20 newly constructed. The hull at frames 20 is now about 1 mm wider in the region of maximum breath than originally. With the help of several buttok lines and the new water lines I have also redesigned the transoms

I haven't add all changes on the test hull, so you can see in the pictures the not entirely harmonious course of the lines.





The first step of my little project -the reconstruction of the lines- is complete.
In between, I have asked myself several times whether the construction of the half-model was even necessary. After the problems in the reconstruction of the transoms and fashion pieces, that define the shape of the stern, have identified, the construction of the test model was more than worth. I am happy to have the mistakes now and not found during the construction of the POF model.

In the next few weeks I'll construct keel, frames and all other components that are needed to build the hull. In autumn I like to start the construction of the POF model. Until then, one last picture which shows the side view of the test hull.
 

Welcome on bord, Antony
 
The completion of the hull of my control model in the region behind the last frames has attracted much longer than expected.
When planning the last phase of the construction I realized that the body plan of the original drawing and therefore my reconstruction at the top of the last two frames is too narrow. So back to the drawing board and the frames 19 and 20 newly constructed. The hull at frames 20 is now about 1 mm wider in the region of maximum breath than originally. With the help of several buttok lines and the new water lines I have also redesigned the transoms

I haven't add all changes on the test hull, so you can see in the pictures the not entirely harmonious course of the lines.





The first step of my little project -the reconstruction of the lines- is complete.
In between, I have asked myself several times whether the construction of the half-model was even necessary. After the problems in the reconstruction of the transoms and fashion pieces, that define the shape of the stern, have identified, the construction of the test model was more than worth. I am happy to have the mistakes now and not found during the construction of the POF model.

In the next few weeks I'll construct keel, frames and all other components that are needed to build the hull. In autumn I like to start the construction of the POF model. Until then, one last picture which shows the side view of the test hull.
 

Welcome on bord, Antony
 
The completion of the hull of my control model in the region behind the last frames has attracted much longer than expected.
When planning the last phase of the construction I realized that the body plan of the original drawing and therefore my reconstruction at the top of the last two frames is too narrow. So back to the drawing board and the frames 19 and 20 newly constructed. The hull at frames 20 is now about 1 mm wider in the region of maximum breath than originally. With the help of several buttok lines and the new water lines I have also redesigned the transoms

I haven't add all changes on the test hull, so you can see in the pictures the not entirely harmonious course of the lines.





The first step of my little project -the reconstruction of the lines- is complete.
In between, I have asked myself several times whether the construction of the half-model was even necessary. After the problems in the reconstruction of the transoms and fashion pieces, that define the shape of the stern, have identified, the construction of the test model was more than worth. I am happy to have the mistakes now and not found during the construction of the POF model.

In the next few weeks I'll construct keel, frames and all other components that are needed to build the hull. In autumn I like to start the construction of the POF model. Until then, one last picture which shows the side view of the test hull.
 

Jack,
 
yes, it's the company. If they speak English I don't know.
If not, I would be pleased to help you because my German is much better than my English

Welcome on bord, Antony
 
The completion of the hull of my control model in the region behind the last frames has attracted much longer than expected.
When planning the last phase of the construction I realized that the body plan of the original drawing and therefore my reconstruction at the top of the last two frames is too narrow. So back to the drawing board and the frames 19 and 20 newly constructed. The hull at frames 20 is now about 1 mm wider in the region of maximum breath than originally. With the help of several buttok lines and the new water lines I have also redesigned the transoms

I haven't add all changes on the test hull, so you can see in the pictures the not entirely harmonious course of the lines.





The first step of my little project -the reconstruction of the lines- is complete.
In between, I have asked myself several times whether the construction of the half-model was even necessary. After the problems in the reconstruction of the transoms and fashion pieces, that define the shape of the stern, have identified, the construction of the test model was more than worth. I am happy to have the mistakes now and not found during the construction of the POF model.

In the next few weeks I'll construct keel, frames and all other components that are needed to build the hull. In autumn I like to start the construction of the POF model. Until then, one last picture which shows the side view of the test hull.
 

Very interesting construction method.
If you paint the outside of the frames black before you glue in the filler pieces, you will have a very good reference line for shapeing the hull.

Welcome on bord, Antony
 
The completion of the hull of my control model in the region behind the last frames has attracted much longer than expected.
When planning the last phase of the construction I realized that the body plan of the original drawing and therefore my reconstruction at the top of the last two frames is too narrow. So back to the drawing board and the frames 19 and 20 newly constructed. The hull at frames 20 is now about 1 mm wider in the region of maximum breath than originally. With the help of several buttok lines and the new water lines I have also redesigned the transoms

I haven't add all changes on the test hull, so you can see in the pictures the not entirely harmonious course of the lines.





The first step of my little project -the reconstruction of the lines- is complete.
In between, I have asked myself several times whether the construction of the half-model was even necessary. After the problems in the reconstruction of the transoms and fashion pieces, that define the shape of the stern, have identified, the construction of the test model was more than worth. I am happy to have the mistakes now and not found during the construction of the POF model.

In the next few weeks I'll construct keel, frames and all other components that are needed to build the hull. In autumn I like to start the construction of the POF model. Until then, one last picture which shows the side view of the test hull.
 

Hello Christian.
This looks like a nice place to learn a new method of hull construction.. Not seen the method before..
Will follow along of this build if you don't mind.
 
Regards Antony.

Hi Anobium/Christian,
thanks to your offer to help me with german language. This is another option I can add to my choices basket. Be sure I'll contact them, and if necessary, I'll involve you. Thanks again. Jack.
 
Saturday, July 11th, 2015
 
For the moment I have installed the keel on the bulkheads . . I'm waiting for the glue to dry. In the meantime I prepared two mini wood blocks to shape the bow. They are so "big" that I had to fix them on a piece of wood to be able to work with them . .
I then began to cut ten/twelve strips of Tanganyika from a sheet of veneer.
01 Brick%20by%20JackAubrey/20150710_113827_zpsdenmzwle.jpg

02 Brick%20by%20JackAubrey/20150710_113812_zpsp7zg4mi4.jpg

03 Brick%20by%20JackAubrey/20150710_113750_zpsoqybwc6t.jpg

04 Brick%20by%20JackAubrey/20150710_113804_zpsnbenchh3.jpg

Rgds, Jack.Aubrey.