-
Posts
438 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by Q A's Revenge
-
Table Saw from tile cutter
Q A's Revenge replied to Q A's Revenge's topic in Modeling tools and Workshop Equipment
Just had a look at Wickes and the cheapest I could find was a bit more at £39.99 but still not bad. Just a couple of quid more for a slitting saw blade and you're good to go. -
You can buy these for about £30 in Wickes.
-
I've got a Stanley and it's pretty poor as well. I may repurpose it somehow.
-
Fine line tape has been used for years in the motor trade so that would be my first choice.
-
Design and Build a Custom Work Station
Q A's Revenge replied to pompey2's topic in Modeling tools and Workshop Equipment
Nice job! -
Checkering tools for carving
Q A's Revenge replied to grsjax's topic in Modeling tools and Workshop Equipment
I don't see why you couldn't use them but you'd need to supplement them with more conventional carving tools as those are a bit specialist. -
I don't know how many folks have had problems with twisted ply parts, is it a very common complaint? I can understand the frustration though when it does happen. I think poor quality ply is probably the biggest problem although bad packaging and storage can obviously cause their own problems. Probably the best solution would be to vacuum pack the sheet parts, that would stop them twisting in storage. If I bought a kit with MDF parts I'd use them as templates to cut new ones from ply wood.
- 25 replies
-
The laser cutter at work had a dedicated fume extraction unit. They also used special "laser cutter MDF" whatever that is. I would imagine the burnt edges of the MDF may be quite toxic once turned into a dust by sanding but don't know if any research has been done on that particular aspect.
- 25 replies
-
The only sheet material that comes to mind that is weaker and less durable than MDF is fibreboard. The fact that kit manufacturers are using MDF is no surprise, it's cheap and easy to cut. There could be some merit in using it in kits rather than sourcing good quality plywood and that's if it reduces the retail price of the kit. Somehow though I can't see that happening. Given the relatively small amount of sheet material in a kit I can't see why a builder would risk the integrity of hundreds, possibly thousands of hours of work just to save a few pounds or dollars on materials.
- 25 replies
-
Take two samples about the same size, one MDF and another Ply. Place them in a tray of water for a few minutes and ask me again... :-)
- 25 replies
-
timing belts and pulleys
Q A's Revenge replied to Kurt Johnson's topic in Modeling tools and Workshop Equipment
You could try a motor factors (car spares) shop. -
Looking forward to seeing how you get on with this.
- 46 replies
-
- dinghy
- Midwest Products
-
(and 2 more)
Tagged with:
-
Tilting Table on Byrnes Saw
Q A's Revenge replied to jhearl's topic in Modeling tools and Workshop Equipment
If it's like my Bandsaw then it's possible to beyond the "Zero" point. Easier to see on this machine but the pointer is also beyond zero and you can clearly see the angle of the blade. As with a full size Table Saw though vertical should always be checked with a square. Nice Digital fence on this one! -
Tilting Table on Byrnes Saw
Q A's Revenge replied to jhearl's topic in Modeling tools and Workshop Equipment
The Proxxon does indeed have the ability to angle the blade like a full size table saw Nigel. Cutting lots of angled strips would be a breeze with this saw. -
Tilting Table on Byrnes Saw
Q A's Revenge replied to jhearl's topic in Modeling tools and Workshop Equipment
I think you're understanding is correct. It appears to be of limited use. -
Tilting Table on Byrnes Saw
Q A's Revenge replied to jhearl's topic in Modeling tools and Workshop Equipment
I think this is perhaps where the design falls down? With a fall size saw with a tilting blade you could just keep cuting off lozenge shapes from a wide board. Not sure how you'd do that with this design? -
Can i live without a BYRNES TABLE SAW
Q A's Revenge replied to shihawk's topic in Modeling tools and Workshop Equipment
Is there anyone on here with both a full size and miniature table saw? I ask as I'm wondering about the safety aspect of using the smaller saw. Full size table saws seem to be regarded as one of the most dangerous wood working machines with several workers in the U.S. loosing digits every week. Does the Byrnes have a riving knife for example or is it not needed on a machine this size? -
Is there a better #11 blade handle
Q A's Revenge replied to roach101761's topic in Modeling tools and Workshop Equipment
Anyone tried the Z series blades, are they any better? http://xacto.com/products/cutting-solutions/blades/classic-blades/11-Blade-Classic-Fine-Point.aspx -
OCCRE PORTABLE WORK BENCH
Q A's Revenge replied to Thunder's topic in Modeling tools and Workshop Equipment
Looks like quite a nice little workstation. No idea of cost but don't see why laser cut parts like that should be too expensive? -
What camera do you use
Q A's Revenge replied to Scholzy's topic in Modeling tools and Workshop Equipment
I use a Pentax DSLR but any digital camera will do. If you can justify the cost try and get something with a moderate size sensor as they yield better results in most cases. If I didn't have a Pentax I'd probably look at Fuji or Panasonic for a quality compact. -
It depends what you need to sharpen and how often. I've seen that particular tool before but not seen good or bad reviews for it. Lots of us have multiple hobbies so some kind of sharpening system may be required. Take wood turning for example. Turning tools need to be kept very sharp so will require regular attention. Woodworkers and Metal workers may also prefer to use something more than a simple double ended grinder. Personally I sharpen most of my tools (Wood and Metal working) on a much modified belt and disc sander. I've bought additional jigs for it and made some of my own. Also on the page you linked was another sharpening system: http://www.rockler.com/robert-sorby-proedge-plus-sharpening-system This is an expensive piece of equipment but really is an extremely easy to use system for wood workers and turners.
-
Home Built Thickness Sander
Q A's Revenge replied to Snowmans's topic in Modeling tools and Workshop Equipment
Nice work, thanks for posting! -
I had to google the 103 to see what it looked like. Can't say I was impressed with the concept of the blade adjustment etc so not one for me. Don't see why it shouldn't work well for you though provide the blade is nice and sharp.
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.