-
Posts
660 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by rvchima
-
Tying Blocks Dave Row kindly posted detailed instructions for seizing a line to a block and attaching it to a yard. His method is pretty much how blocks are attached on real ships and the results are perfect. But it does take a while. I experimented and found a method that is a bit easier and looks OK to me. Hold the block in a spring clamp in a vise. Note to self - make sure the holes in the block are vertical so you don't tie the line over the holes. Slide the line behind the block. Tie the line with a tight square knot. Remove the block from the clamp, loop the long end of the line over the top, and put the block and line back in the clamp. Use the short end of the line to tie 2 or 3 tight half hitches around the loop. This approximates the seizing but is easier. The fake seizing line is the wrong diameter but mostly gets hidden against a yard anyway. Don't glue anything yet.Voila, the finished block. Slip the loop over the yard and pull the long end of the line to snug it in place. Put a drop of CA on the knot and around the block, then trim the short end of the line. It takes me about 3.5 minutes per block. This method doesn't look so good for blocks attached to a line, like the blocks hanging from the ends of the yards. For those blocks I am using exactly the method described by Dave, seizing them to the line with a separate, thinner line. That method requires a third hand to hold the seizing line. I used a couple of strong neodymium magnets to attach a micro clip (from my model rocket days) to my spring clamp. See Dave's post for the rest.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Yards I've got all the yards, flagpoles, and booms shaped. Thanks to Pat Banyan I ordered a jack, ensign, and commissioning pennant from Cornwall Model Boats. The main yard and main topsail yard are rigged. Oh s**t - I forgot the stunsail booms on the main yard! I've seen how Pat Banyan and Dave Row both made their fittings out of brass tubes and wire soldered together, and had visions of deconstructing the yard to slide the bands on. Then I looked at the Caldercraft plans. The rings are pot metal, almost no cleanup required. The bands are photo etched brass that just go 2/3 of the way around the yard. I looked back (longingly) at Chuck Passaro's thoroughly detailed 132 page plans for the Syren that I built 5 years ago. Chuck said that there is no need to solder the fittings because there is absolutely no load on them. No way to solder the pot metal anyway, so after a little metal work, a drop of CA, and a little paint, the stunsail booms were done. I put the booms on the fore yard before I rigged it ;^)
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Masts Completed, 1 year, 24 days, 456 hours The masts alone took 58 hours. They are still in separate sections and are not attached to the ship. The deadeyes are set into the tops.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Dave, Thank you for all the advice on rigging the blocks. Your photos really help explain the process, which is not too complicated after you see it. And I'll echo Fernando in complimenting your rigging tools. I've been working with a spring clamp held in a vise and two old fingers. It's time for me to get a little more sophisticated. Rod
-
Dave, Your single tye blocks (below from pp 26) are very clever. I can almost imagine how you make them based on some of your other posts, but would you consider showing an overview? It seems like the short end is cut off at the seizing. How do you prevent it from pulling out? Many thanks. Rod
-
Simply beautiful Dave! Thanks for all the effort you've put into your build log. It has been a great reference for me. Rod
-
Bowsprit, Fore Mast, Fore Topgallant, Main Mast, and Main Topgallant Complete. 1 year, 9 days, 411 hours I actually completed the bowsprit and jibboom before my holiday but didn't have time to post. I did the rest over the last 2 weeks. Here are some detail shots. I I really like this drawing in Parkin's book of the Endeavour with only the main masts and standing rigging. I am toying with the idea of stopping my build at that point. This would make for a much more compact display case and probably save me 6 months. What do you think? Then I could get to these other projects waiting on my shelf sooner. That would be an Aeronaut kit of the Prinz Eugen heavy cruiser, a vintage Sterling kit of a P-61 Black Widow night fighter, and a Bomarc missile kit by Madcow rocketry. So many projects, so little time ;^)
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
IMG_E7060.MOV I've been back from my holiday for a couple of weeks and promised to post a few photos. Here's a view from the stern of our ship. The wheel is just spinning freely in the water but it sure looks cool. The Columbia River Maritime Museum in Astoria, Oregon has the Columbia light ship anchored outside. Our ship docked right next to it. The museum was packed with ship models like this model of the Columbia Rediviva, the first ship to "cross the bar" into the Columbia River in the Pacific Northwest in 1792. They also had a second edition of the logs of Captain Cook, who explored the Northwest coast on his third voyage in 1778. I'll skip the photos of Portland, Oregon, Mt. Rainier National Park, and Olympic National Park, and end with this photo of the harbor in Victoria, BC. The domed building is the capitol building of British Columbia. The Royal BC museum is just off the photo to the left, and our hotel was the building on the right with the pointy tower and flag. What a beautiful city. I've been busy building masts. Give me a couple of hours to take photos and I'll be back.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
We are cruising through the Columbia River gorge in the American Pride, a "stern wheeler" with two steerable props and a free-wheeling wheel. At 295 ft it's about twice the length of the Endeavour.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
This morning I was tying 3mm blocks to eyebolts, getting ready for the tops. Near the end one block went flying. Far. I got down on my hands and knees with a flood light and searched the floor, with no luck. Then I swept the floor. Still no luck so I gave up. Two hours later I was washing dishes, and felt something on my head. The block was in my hair.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Holiday Break My wife and I are leaving tomorrow for a week-long cruise through the Columbia River gorge on a modern stern wheeler. It covers the most of the width of the state of Oregon. Then we'll rent a car and visit Portland, Oregon, Mt. Rainier National Park, Olympic National Park, and Victoria, British Columbia, Canada. I'll post photos of any interesting river craft. Back in mid August.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
I just bought an interesting book at a local used book store. "The Neophyte Shipmodeler's JACKSTAY," by George F. Cambell, published by Model Shipways, 1962. It's 59 pages softbound and full of labeled drawings of sailing ship parts. It explains pretty well what things are called, how they work, and how they changed over time. It even explains what a jackstay is. There is no index but it's easy to flip through and find a relevant drawing. My favorite part is The Rigging It has been truly said that the rankest amateur can successfully rig, though he know not his mast from a hole in the ground. The original price was $2.50 US. I paid $8.99 for a 56 year old copy. And amazingly Modelexpo-online.com still has it for sale for $12.99.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Fernando, Welcome aboard! I should explain that, in the model airplane world, what I am doing would be called standoff scale. It looks pretty good if you stand off a ways. If you want serious attention to detail check out Pat Banyan's completed build or Dave Rowe's nearly completed build.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
I love the hand drawn plans for the Gaff! Here's a man who plans what to do next. I usually just dream about it in the morning as I hit the snooze alarm again.
-
Anchors I decided that I could safely attach the forward anchors now. I left a coil of line to attach to an anchor buoy eventually.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Swivel Guns These are just a couple of pieces of PE brass with a nail through the center soldered together. Bend up the tabs and attach the brass barrel with a piece of wire, then solder the wire. Like always I used Novocan black stained glass patina for the black color.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Hi Dave, I definitely have not paid enough attention to your build log. i just went through the last 10 - 12 pages of your log and realized that you pay as much attention to detail in your log as you do in your build. I saw a lot of details about how you built your masts, spars, and rigging that will be a huge help when (if?) I ever get to that point. I'll keep following the new posts and searching the old for ideas that I can use. Rod
-
Boat Storage The longboat and pinnace go in cradles on deck. They look awesome up there. Eight spare top masts are lashed to the tops of the bits fore and aft of the boats. While I was making spare masts I went ahead and made another set. That way I could use the worst ones as spares and the best ones above. The spare masts are lashed in place. If I'd known I would be doing this much lashing in 2018 I would have paid more attention in Boy Scouts in 1968. The longboat and yawl are lashed atop the spare masts. Someone please tell me why I spent so much extra time and money on a curved grating kit for the main deck hatch. Now I totally understand why Pat Banyan built his model with only 2 boats aboard. My wife Cinda Chima is an author of popular young adult fantasy novels. She posted a photo of my model similar to the one below on Instagram the other day, because her latest series includes scenes with pirates. Her post has 161 Likes right now. I told her I don't have 161 Likes TOTAL in all my posts on MSW.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Barrels? The kit came with a little bag of nice wooden barrels, but, like the oars, is no mention of barrels in the instructions or plans. Where would these go? Lashed to something on deck somewhere?
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Oars The kit came with a lot of photo-etched brass oars in 2 lengths. There is no mention of oars in the instructions or plans, but they obviously go with the ship's boats. The p-e brass parts in this kit are beautiful, but flat oars just didn't look right because they stack up flat. I briefly considered carving 24 oars out of basswood, but only briefly. Instead I decided on composite oars with brass blades and wooden handles. The handles on the brass pieces were 1.2 mm across. I thought about buying a draw plate to make the handles, but our friends at Bluejacket Shipcrafters had 1.2 mm dowels sold as treenails. Besides, the 10 mm dowel supplied with the kit for the mainmast was misshapen and Bluejacket had that too. I ordered 2 of each and had them in 2 days. I cut the 1.2 mm dowels to length, spun them in a rotary tool and shape the handles, and split the other end. I cut the blades off the p-e brass oars, glued them to the handles, painted my composite oars, and tied them into little bundles for the boats. You can see them in the previous post.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Ships Boats Completed The instructions said that the ship's boats should take a couple of weeks. That was a little optimistic - they took about 60 hours over 19 days, but I build fast. The only problem with the plank-on-frame construction is that the floor ends up too close to the side rails. The poor sailors would have to sit with their knees to their chins. The clinker-built construction of the yawl and skiff came out better than I expected.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Happy 4th of July Everyone! On this date in 1776 Captain James Cook had an honorary retirement from the Royal Navy, with a posting as an officer of the Greenwich Hospital; he was made a Fellow of the Royal Society, and awarded the Copley Gold Medal for completing his second voyage without losing a man to scurvy. Nathaniel Dance-Holland painted his portrait; he dined with James Boswell; he was described in the House of Lords as "the first navigator in Europe". In the US we celebrate with hotdogs and beer.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Thanks Dave. I did one anchor ring puddenning with CA and didn't like the way it looked. I started over with PVA and it looks much better. I'll try it again when I get to the real rigging.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Ship's Boats The 4 ship's boats are built just like the full model - double planked over a frame. Here is a photo of the 4 boats in various stages of construction with comments. From top to bottom: Yawl The frame pieces don't match up very well even after everything has been sanded a lot. Skiff The first layer of planking is covered with a layer of Timbermate wood filler that needs to be sanded. A block of wood is attached to the inside of the boat with double-sided tape. It is used to hold the boat in my vise during construction. The yawl and skiff are supposed to be clinker-built, but I don't know if I can do that cleanly on these tiny boats. They may end up with smooth hulls. Pat Banyan built a beautiful longboat and pinnace for his Endeavour . Mine won't be that nice Pinnace This has 2 layers of planking and is ready for a second coat of filler. Longboat I put several coats of Krylon gloss enamel on the hull and it looked perfect, until I glued on the wales. The CA just lifted the paint right off the hull. I got everything together without too much damage, but now I'm worried about the interior pieces and the other boats. I guess I'll experiment with other paints. The frames have to be removed after construction. The instructions say to twist them off with needle nosed pliers. This seemed unlikely but worked perfectly. However this leaves a very rough floor in the boat that needs to be planked over. That's the next step.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
-
Anchors I won't be able to attach the anchors until the rigging is done, but I built them just for fun.
- 108 replies
-
- endeavour
- caldercraft
-
(and 1 more)
Tagged with:
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.