davyboy

Out of curiosity I visited the pirates forum and read the article about Chuck's Speedwell. I had a really good laugh at the comment by one of their admin wallahs. "Luckily we have same quality kits from Chinese manufacturers at one third of the price". Quality ???? What planet is that guy on ? Keep up the good work Chuck,I enjoy following your build. Sorry I wont be building your Speedwell as I've started rigging my 1/48th POB version after 5 years of work .  
 
Dave 

Out of curiosity I visited the pirates forum and read the article about Chuck's Speedwell. I had a really good laugh at the comment by one of their admin wallahs. "Luckily we have same quality kits from Chinese manufacturers at one third of the price". Quality ???? What planet is that guy on ? Keep up the good work Chuck,I enjoy following your build. Sorry I wont be building your Speedwell as I've started rigging my 1/48th POB version after 5 years of work .  
 
Dave 

Do you just want it done so you can move on?  Is there a deadline?  Cutting corners may get you somewhere faster, but it tends to magnify errors, not just in looks, but in frequency.
I glued all 500ish piece of scale-length decking (cut from 4 foot lengths) on my 5 foot long hull when I easily could have scribed some plywood.  There were a couple of places I had to pull a piece off and put in another, reusing the removed piece somewhere else.  That would have been a bigger pain using full 4 foot lengths.  When it was done, none of the left-over scrap was longer than an inch, so doing it this way was a more efficient use of materials.
 
I recommend all planking/plating be done in scale pieces on anything 1:64 scale and up, because you get more from it that way.  The decision,of course, is only yours to make.

Good morning everyone ☺️  
 
 

I have coated the boat with oil and made a slipway. Once assembled, it turned out to look like this. Macro photography revealed some disadvantages, but in the future I will eliminate them.

Yeah, but he'd be a lot faster making the next 50. 😉

Those look terrific, Chuck.
 
I'm sorry to read that Troll City over at SOS is still alive and bitching.... I suppose that trolls have to live somewhere.

Yes, another forum but seriously most already know what they are like...thats why I wanted to post publicly for everyone not to take the bait.   Its just not worth it.    Just stay clear of the whole bunch.
 
Chuck

Excuse the newbie ignorance but I assume that is another forum?
Again as a newbie to the hobby I can't imagine (other than insecurity and jealousy( what folk can say negatively about your work. Having looked at a lot of kits before moving on from my first (admittedly online) the only kits I really wanted to try were yours and Vanguards. On all of the build logs here it comes across so strongly how high the quality of both your kits are to give any stage of modeller the very best chance of making something stunning. Yes they are expensive but you get what you pay for in most areas and this is definitely one.
Good luck to you!
 

I am just about to post an update with those...LOL
 
The gratings for Speedwell are different but the same basic concept.  They are a different scale to reflect the larger size needed.  They will have 1/16" square openings which at 3/8" scale would be a 2" hole.  Just right and exactly the same number of holes as the contemporary model.
 
These will all be included in the chapter along with the jig needed.
 
I will have construction pics really soon.
 
I have been distracted lately with the topic on the SOS where the staff and admin are trashing this project relentlessly....but its a lot fun to watch.   Many of you guys have sent me messages alerting me about it.
 
I have to thank Ben however for being a brave soul to have something nice to say about it knowing he will get the wrath for it.   I must be the worst kit designer in the world if you read some of that stuff over there.  But seriously...dont put yourself out there because if you do say anything positive about Syren or any of my projects on SOS they will lambaste you.  So no worries.   Dont put yourself in that position.  Its not worth it.   Most folks know its all nonsense.  And I am well aware.  But thanks for the positive notes of private support.
 
Anyway...back to building gratings.

That would be so nice but it probably would put the builder at risk of being abused.
 
Anyway....those gratings
 
You will basically get all of the laser cut parts in this chapter.  There are only four hatches with gratings.  They are not very large.   Here are all of the elements needed.  You will get two layers for the jig.   The two layers are glued together to form the jig.
 
You also get a right angle jig which is 3/64" thick.  The thickness is very important.
 
Lets get started.
 

Start with the coamings.   They are laser cut and 1/8" thick.
 
The fore and aft sides are already shaped with the round-up of the deck....or camber as usually described but is an inaccurate term.
 
Use the right angle jig to glue two sides together...dont worry about the laser char just yet.   Then glue the remaining two sides together using the same jig to make a nice right angle.
 

Glue the two right angles together to form the coaming.  Sand the sides clean which are left a bit longer as you can see in order to remove the char and leave a nice bright smooth surface.   Also sand the top sides to clean the char.  You can see the cleaned coaming below.
 
Then you can start working on the grating.  Again just like my other smaller scale grating kits.
 
Insert the laser cut grating strips in the slotted jig.  NO GLUE of course!!!   This is just for alignment.
 
Then start adding the cross battens.  These are glued in position.  They may be too tight as you want a press fit.  So just run the small strips 1/16" x 1/16" through your fingers with some fine sandpaper.  Not much.  Just enough so the battens fit into the slots. see below.  There are seven batten strips and seven laser cut grating strips for three of the hatches.  The fourth is made the same way but is much smaller on the fcastle.
 

When all the strips are glued in position,  remove the grating from the jig.  Snip off the edges as shown below.  Then sand all four edges clean.  Try and not distort the perfect square shape.  In the photo two sides have the ends snipped off.   The smaller hatchway will have fewer battens and more to snip away.  Also sand the top surface clean and smooth.  Once again try and maintain the proper shape with the round-up.  You will know when its all done when the char is cleaned from the laser cut grating strip squares.

The photo below shows the top of the grating and sides all clean and nice and smooth.  It makes a nice grating.  The holes are 1/16" or 2" on the real ship and perfectly in scale.

You should but dont have to sand the bottom side as well.   Here is a look.  The battens are clearly less thick than the grating strips and these are pretty close to actual construction methods.  Or at least the impression of it.
 

And almost done...you will see how nice and tight the grating fits in the coaming.   Dont over sand the edges and you should test the grating in the coaming as you sand the edges.   In fact, the coaming normally has ledges on the port and starboard sides inside the coaming.  These create a ledge that the grating sits on so it doesnt fall through.  You can add those if you like.  But in my case the gratings fit so snug that they were not required.  I simply glued the gratings into the coamings making sure the top of the coaming was flush with the grating.  I sanded it smooth with some 400 grit paper.

The four corners of the coaming are very sharp at this point.  You dont want that.  They should be rounded off.  But they are only rounded off down to the deck level.   That is when you take that same right angle jig and use it.
 
The jig is the same thickness as the planking.   So you can place the coaming into the corner and use a sharp #11 blade to slice away the corner.  Slice it down to the top of the jig only.   You can make a stop cut at the jig level before slicing off the corner.  Then just round off the corner.
 
 
Dont slice off too much.   Just a little bit to round off each corner.
 
To finish it off I drilled three holes with a #76 bit.  I used 20lb black fishing line to simulate the bolts on the top of the coamings.  Three on each side.   They cut flush with the top of the coamings with a sharp blade.
 
All done!!!
 
 
 

Good move Chris,

The one in the centre is apparently Nelson's sword found in his cabin after Trafalgar.
The ones right and left are the surrendered French and Spanish swords.
 
Cheers,
 
B.E.
 

A tin of biscuits.  
 
 All kidding aside, ship's boats carried lanterns though I've never see a model where a lantern was part of the ship's boat contents.  

Jumping from task to task again but I can't fix no 18 - 20 till I know where the deck will be. So I have created beams a cross 14 to 18 so far so I can line up the camber of the main deck. These are clamped up because I have laminated coffee stirrers to create these beams and they are only dry fitted and clamped into place. You can't have too many clamps. 
There will be supports fore and aft. If I was Chuck, there would be half lap joints on every junction but I am going to cheat, there will be tabs glued to the underside of the junction so I can glue the fore/aft pieces without awkward clamping tasks. 
 

Had some time today and started checking the profiles with a length of 1mm x 5mm beech. Mostly just a case of removing excess or putting on strips where cut to fine.

Starboard mostly done but port side still to do. Bulkhead 18, 19 and 20 might be a bit of a challenge. 

Some more progress. I've installed the wales, the lower one was difficult to bend at the stern but I got it done. I've also gone ahead and trimmed the frames to their (almost) correct height and made the cutouts for the upper gun emplacements (not shown on the first photo which is from a week ago).
I'm now turning my attention to the interior, I installed the keelson and will start on the strakes on which the deck beams are resting.

Mast parts done. Topmasts supplemented with pulleys..


Making basket supports called Mast Cheeks. Again processing the glued and then soaked parts..





I have already reached model height..💥



 

Hello,
it is done. At least the wheels are ready build. Next to build are the two supporters for the wheels.

Both platforms are done:

Foremast Crows Feet Rigging
Over the last couple of days I have been working on adding the crows feet rigging to the foremast.
 
The first task was to add a 2mm single block to the top forestay.

The next task was to add another 2mm single block to the euphroe.

Next up was to rig the two blocks. I found it useful to use a clamp to hold the euphroe whilst adding the inter-block rigging.

Before I started to add the crows feet rigging I did map out the required path. I also calculated the required length of thread. I opted for a generous 2.2m length but in the end a length of 1.8m would have been sufficient.

It was then a case of following the required path as the rigging was added. I have added a few photo's taken of the work in progress.

The rigging is now complete and the free end is ready to be tied off. once I have adjusted the required and applied some tension.

I used a slip knot to secure the free end. The crows feet rigging is now complete.

 
 

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Life finds a way (to get in the way) but some progress has been made, the keel and rabbet is assembled and I have sanded a first approximation of the head taper.
The scale of the model hit home in a different way when the keel was laid. Its quite large, in a good way. Having it occupying the desk is different from the theory of it will be 32"  :).


 
 
I'm not sure whether the taper should be continued down towards the waterline or stop roughly as it does now. Also unsure if it should be taken further towards the stern. For the figure to sit without any tension I should reduce the width a bit more, fractions of a millimetre, but I'm starting to eat into the thinner knee (correct part name? the fancy piece with notches). Perhaps that's as it should be?

 
Chuck, thanks for the advice on sanding parts while in the sheet!
When sanding the head I had to remove to much material around the box joint, I think I did a bad job when clamping the pieces during gluing so they were not perfectly in plane. I didn't really notice how much I removed at the time but it became obvious when mating the head to the keel. Next I plan to sand the keel around the box joint in the problem area to get a nice transition from head to keel. It will be a bit thinner that it should be but it is what it is. After that I will finish sanding the surface with high grit and apply some surface protection before mounting the aprons.


 
The kit came with enough spare parts for one additional complete head and keel assembly so I'm toying with the idea of assembling that and comparing the results. Possibly using poly for one and shellac on the other, for science as it were.

I'm greatly enjoying the project so far, it delivers on creating a sense of building the model, rather than assembling it, which is what I was hoping for.

I have completed the rabbet strip and the false keel. Looking good so far and goes together easily.