dafi

Post One Hundred and Seventy
 
Completing the Cutter.
 
Apart from painting the bottom Ivory, and the wale Black/grey, the boat will be finished using w-o-p only.
 
The rudder is a plain laser cut affair intended I think to simply display in the sternsheets of the boat. There are no fixings to hang the rudder either on the stern post, transom, or rudder.
 
I chose to add these fittings including a tiller of the yoke type.

4287
Still requires a little further fining down, this is the third attempt which may still break.

4289
Trial fitting the rudder.; a few tweaks required.
 
One consequence of changing the rowing arrangement from double to single banking is that the provided oars are too short for purpose.

4290
They are fairly easily modified but it does require using two oars to produce one. 
To improve the look of the oars the blades should really be thinned towards the tip.

4295

4298

4299

4311
Set -up for single banked rowing.

4302

4306

4307
I quite like the look of her on the skids and the Pinnace and Cutter don’t obscure much of the Main deck.
 
B.E.
16/04/2024

Post One Hundred and Sixty – nine
 
Progressing the 24’ cutter
The floor of the cutter is covered by gratings at the stern, open boarded footwaling for the body, and a small close board platform at the bow.

4265
I changed the footwaling to a close boarded version as shown in the AotS book Diana which contains 1:48 scale drawings of a 24’ cutter.
 
Before I add the ‘false’ ribs I use a copy of the kit plan to mark the positions of the thwarts.
Positioning the ribs really needs to take into consideration the position of the thwarts and the related rowlocks for the oars, which are cut into the wash strake.

4268
The AotS drawings show the 24’ cutter arranged for single banked rowing. This is the arrangement I will follow, apart from any other consideration, there are less rowlocks to cut.

4270
I firstly fix only those ribs that fit aft of the thwarts before fixing the Rising, (thwart support strips) The remaining ribs can be slotted behind the Risings in the correct positions.
The risings are fitted using a 4mm depth gauge but in fact follow the line of the second strake down from the top.
 
Once fitted it is useful to check both the levels and the correct height of the thwarts above the footwaling.

4273
My 1:64 scale figures are useful for this purpose.

4275
I would like to see a sitting figure produced by Vanguard. A sitting Captain would serve well to give scale to the splendid Vanguard cabin furniture, and also the stern sheets of the boat range.

4277
I like to add small features to the boats such as here; the cap square for the Mainmast and step to take the mast heel on the Keelson.

4279

4280

4281

4280
Needs cleaning up now before finishing.
 
B.E.
15/04/2024
 
 

The question I am having is: Did in Soleil´s days those ports were pointing foreward or aft as seen in Vasa?













... and the 2 last ports each deck are pointing aft.









Nicely to be seen in the small reconstruction of the upper gundeck. Those guns can hardly be pointed the conventional way with 90° to the ship´s center line





Also on "head chasers" on the upper deck are pointing forewards.



... thus avoiding the cathead-knee 🙂



Something that went wrong on the 1:10 model, where these guns have to be placed over the cathead-knees 😉



By the way, the lower deck guns have the same errata.

XXXDAn

Hello Eric,
 
to avoid friction, the tube should be pointing downwards 🙂
 
Anyway I do not know, if at that time this protection was already invented. I believe you can easily skip it.
 
And just to confuse you even more, the monograhy from Gerad Delacroix "The SAINT-Philippe 1693-1715" shows two lanyards, but that was a tad later build. Here a picture that I took on the exhibition in Rochefort in 2018.

Also have a look here at the gods of french arsenal building:
https://5500.forumactif.org/f92-le-saint-philippe-1693-1715-plans-jean-claude-lemineur
https://5500.forumactif.org/f11-le-vaisseau-de-colbert-1670-plans-anonymes
https://5500.forumactif.org/f31-la-renommee-1744-plans-jean-boudriot
 

Hello Eric, very nice start 🙂
 
Ian is putting lot of confidence in my knowledge, but I think Hubac is much closer to this time frame than me with my Victory.
 
Here is the aforementioned change of the guns: Trunnions more to the back and axxis more apart, It immediately looses the "toygun"-flair 😉
 

 
As for the pot lids, it was still common at this timeframe just to have 1 lanyard, when they actually changed to 2 I am not sure. And if Soleil was equipped with 2 I know even less 🙂
 
Some hints are given by the "adaptation of SR’s sister ship La Reyne into Soleil Royal" of Hubac´s last post, only showing one ring on the bottom side and the contemporary (HMS) Prince´s contemporary model that also only shows one lanyard per gunport.
 
But if you use 2 lanyards the rings were usually fastened at the end of the metal strips and not inbetween. See the gunport fittings of my Victory. And you also see that even in those later days the smaller gunports also had only 1 lanyard 🙂
 

More about this topic here:
 
Also I used two brass wires to fox the lid to the hulll, this enabling a small gap, here a early version.

 
Together with the small eyebolts from my sets this should look like the following pictures. This should give you the scale of the ensemble of the eyebolts and the according rings, be it 1 or 2 lanyards. First one of implementing the rings onto the eyebolts, second the finished lanyard with leather protection for the inlet hole that was made out of bored out and pulled sprue 🙂


 
Hope this helps, DAniel
 
Just to round up, here a picture of my rendition, also a restart after almost 30 years of tinkering abstinence 🙂

 
 

Here are the results of some of my research. Even though the preventer breeching line - as propagated by Goodwin - is still quite doubtful to me, I tried some different ways for the tackles as shown already in the contemporary sources mentioned above.
First was to determine the length the tackle has that is really needed for the full compliment
of gun crew pulling on it.

 
In my opinion very important: Give the tackles stopper knots at the backwards blocks, the carriage or the cascabel if none of the crew holds it!
Otherwise the gun will run loose ...
Also all trials of arranging the tackles will be useless in a minute or after the first wave. Also do look that the rope has a realistic slack in it. Often seen are tackles coming out of the unsecured block and running in a straight line into a flemish eye, no way of reproducing that in real life 😉
 
Here are my favorites. V1 or V2 are for "prepared for action", V3 and V4 much more for run out but secured guns.   
V1 tackles laid in flakes beside the gun, keeps clear the passage behind the gun
V2 tackles laid in flakes behind the gun, keeps them clear the breeching line and in position for the crew to grab it.

V3 tackles laid in flakes over the barrel, gun run out but secured, as seen today on Constitution

V4 tackles laid in flakes over the barrel as V3, but with a seizure to keep it arranged
That is the version I opted for in my display as these guns are secured but run out and it keeps clear the floor.

 

 
Also already discussed how much the sponge and rammer point out the port, just see here:

 

 

 
And action 🙂
 

 
XXXDAn

Nice and relaxing getting onto something easy. Side entry port and steps. Tape to stop any rogue steps disappearing inside the hull. The elm tree pump lining flew off across the room but I was amazed to find it again. Fenders and chesstrees next.

I’m almost resentful of this fine spring weather as it takes me away from the ‘dock yards’ and my work on Victory. I said almost. 😊☀️ Regardless, in between outdoor chores I’m making slow but steady progress on the bow. ‘Guys’ and Martingales rigged and under tension, Jib inhaul & outhaul installed, spritsail yard sling & horses installed (jib boom horses were already in place), fore netting and gangboard netting ‘sewn’ in place. I’m quickly running out of real estate on the jib boom but I still have lots more to go (rigging AND questions 😉). Comments, questions, and suggestions, always welcomed!
In the meantime, I have a few questions of my own. Many thanks in advance!
Eye bolts on bowsprit block: How many are there? I can account for 4:  2 on the upper port/SB edges for the gangboard netting. One on the port fore face for the jib outhauler and another one the SB side for the jib inhauler.  I’m certain there’s at least 2 more - for the halliards? Plus, there appears to a pair of blocks lashed to the block. Ropes that belay on the timber heads: Longridge makes no mention of 'excess' rope. Do a make a coil of rope for each timber head? ‘Guy’ tackle: I left plenty of excess rope where the tackle hooks to an eyebolt at the beakhead bulkhead, but how do these finish - as with the other tackle, do I frap around the running end a couple of turns between the blocks? Eye bolts at the base of the masts: per the below sketch, is this the correct arrangement?

I had originally glued fast the spritsail & spritsail topsail yards against the bowsprit & jib boom. This made the area even more difficult to work around so I carefully prised these off and installed a dowel and a small wire and so the yards would hang slightly below the bowsprit and jib boom. Maaybe a bit too low on the spritsail yard but the extra clearance helps with all the rigging bits that are starting to accumulate. I fashioned eyes from thread hardened with a touch of CA in place of the thimbles specified by Longridge for the guys.








The mandatory jars of Branston pickle for our Saint George’s Day get together this coming Saturday (official day is Sunday) 😁🏴󠁧󠁢󠁥󠁮󠁧󠁿 

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

Another difference I noticed are the yard tackle blocks and the braces pendants.
 

 
 
Steel mentions that the pendants of the braces of the main yard*** were 1/10 of the length of the yard. In the navy they were sometimes operated without pendants, i.e. the block was lashed directly to the yardarm.
In this matter, one probably has the freedom, as long as no direct references can be found in the logbooks. Are there any hints for that? @Morgan
 
It is interesting to note that Steel has replaced many long tackle blocks with normal double blocks. In particular, the stay tackle blocks and the yard tackle blocks are equipped with 17" double blocks instead of 24" long tackle blocks. More stable blocks or simplification of the material list? Or signs of the beginning machine milling of blocks? All other sources speak of violin blocks for the entire time frame.
Steel also gives the length of the pendants of the yard tackle blocks as 1/10 of the yardarm length. In many other sources I have the impression that the pendants extend to the fishing in the middle of the yard, i.e. they were about twice as long.
 
The two different versions are shown opposite each other in the picture.
 
And how could it be otherwise, questions upon questions ...
 
XXXDAn
 
*** The brace pendants of the foresail are 1/8 of the yard length according to the Steel

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

After the leechline and bowline blocks had worked out so well, we continued with the tricing lines of the yard tackles pendants.

The block on the yard tackle pendant was hauled to the yard with the outer tricing line and the lower block with hooks was hauled with the inner tricing lines to the shrouds to be hooked/fastened there. Unlike other load rigs, the yard tackles were not struck off when not in use, but were also used as to support the braces in strong winds or for other purposes.

And so that the whole thing doesn't get too boring, this time the blocks are 7" and 8", i.e. 2 mm in my scale. But it doesn't matter, it works just like the other 🙂

First on the filed needle, then stropped in as usual ...



... and succeding the function test.



Fits. Then, as usual, tied the eyes with the pointed clamping tweezers and quickly put them all on the leash, such a stopped block is too quickly inhaled.



And to show that you can get these blocks to the yard even with sausage fingers like mine ...



... you just have to make sure that you …



… get not tangled. And already finished.



You can clearly see the noticeable difference between the 2 mm block of the tricing line and the 2.5 mm blocks of the leechline.

The tricing line is one of the thinnest in the entire rigging, here hanging loosely with the yard tackle in use ...



... and with the yard tackle pulled up.



For the sake of completeness, the inner tricing line next to the 4 mm clue line block.



XXXDAn

Well, what can I say. I'm only away for a few weeks because of work and already my tinkering room doesn't want to let me back in ...

"What does THIS strange man want here?!" was one of the nicer questions I had to listen to ...

After some persuasion à la "man cave whisperer", I was allowed to do something in there after all. In the meantime, I had revised my lists of blocks for the Victory again. I had noticed that McKay had left out some quite some blocks in the AOTS and that there were also some errors among them. I had therefore plowed through the entire Steel of 1795 and worked through the various entries, compared them and selected the most plausible variant, possibly adding variants. All in all, there were significantly more blocks added, both the standard blocks and the special types. But more on that later.

The last thing I did was to replace the square shoulder blocks, which are used on the ship today and which McKay also shows, with contemporary round ones. The main yard continues to serve as a model playing field. Here is a reminder of the last status.





Next came 3 x 2.5 mm blocks on each side for the belly and nock gordings.



Check on the tweezers whether the paint application is complete and either brush on the tweezers immediately ...



... or after the block has been pinned. Place a strop around the fixed block as described before ...



... and checked the length in place. Since the block hangs in front of the yard, the legs must of course be different lengths.



The pointed tweezers with clamping function do a good job here, first one side ...



... and neatly trimmed, and the other and you're done 🙂



Here is a comparison of the simplified version with a simple knot on the top of the yardarm and the more correct solution with a lashing.

Since the lashing is tricky to thread, a classic needle helps.



And this is how it should look 🙂



With this technique, I'm now just as fast for the small blocks as I am for the large ones 🙂

XXXDAn  

Well, what can I say. I'm only away for a few weeks because of work and already my tinkering room doesn't want to let me back in ...

"What does THIS strange man want here?!" was one of the nicer questions I had to listen to ...

After some persuasion à la "man cave whisperer", I was allowed to do something in there after all. In the meantime, I had revised my lists of blocks for the Victory again. I had noticed that McKay had left out some quite some blocks in the AOTS and that there were also some errors among them. I had therefore plowed through the entire Steel of 1795 and worked through the various entries, compared them and selected the most plausible variant, possibly adding variants. All in all, there were significantly more blocks added, both the standard blocks and the special types. But more on that later.

The last thing I did was to replace the square shoulder blocks, which are used on the ship today and which McKay also shows, with contemporary round ones. The main yard continues to serve as a model playing field. Here is a reminder of the last status.





Next came 3 x 2.5 mm blocks on each side for the belly and nock gordings.



Check on the tweezers whether the paint application is complete and either brush on the tweezers immediately ...



... or after the block has been pinned. Place a strop around the fixed block as described before ...



... and checked the length in place. Since the block hangs in front of the yard, the legs must of course be different lengths.



The pointed tweezers with clamping function do a good job here, first one side ...



... and neatly trimmed, and the other and you're done 🙂



Here is a comparison of the simplified version with a simple knot on the top of the yardarm and the more correct solution with a lashing.

Since the lashing is tricky to thread, a classic needle helps.



And this is how it should look 🙂



With this technique, I'm now just as fast for the small blocks as I am for the large ones 🙂

XXXDAn