tlevine

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

If you are referring to hull planking, consider the NRG hull planking model and look at the hull planking link under my signature.

If you are referring to hull planking, consider the NRG hull planking model and look at the hull planking link under my signature.

Cordialement fP 

Bonjour, 
J ai mis 26  de 12 livres et 16 de 6 livres  
Des Carronades  ont été embarquées mais misent en place ?

Ah! - Jan - what you need is nose enhancement implants. 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

For anybody interested, the kit is now available through the NRG store.  https://thenrgstore.org/collections/plans-and-projects/products/masting-and-rigging-kit
 
The jeers are the pulley system used to raise and lower the lower yard.  This ship has three jeer blocks, one attached to the lower yard and two others suspended by strops from the masthead.  These blocks are not included in the kit.  They are large enough that they are not difficult to make.  The jeer tye runs through the blocks.  The tye is a 6” rope with a scale diameter of 0.04”; the opening for the sheave is just large enough to allow the rope to run through it.
 
Look at the block proportion drawing.  The sheave opening width is “1” on the drawing.  The length of the block is 8, the width is 4, and the breadth is 6.  The sheave opening length is 5.5 times the sheave opening width.  It is not centered in the block, as shown in the drawing.  The jeer blocks have a double strop, so the blocks will need two grooves on their sides instead of just one.

 
To make the three blocks, I took a piece of boxwood a little larger than required and sanded the sides to the correct width and breadth.  Sanding instead of sawing prevented any burn marks on the wood.  The tops and bottoms of the three blocks, the sheave opening and the strop grooves were drawn onto the wood.  A  space was left between the blocks to make shaping the bottom of the blocks easier.  These blocks will have a false sheave and the sheave bolt is omitted because it is hidden by the strop.
 
I started with the sheave opening.  A 0.045” opening corresponds to a #57 drill bit.  I drilled the holes for all three blocks at the same time.  I used a drill press but this could be done with a pin vise.  The key is to keep the drill bit exactly at 90 degrees to the wood strip.  If you do not have a drill press, I would suggest drilling shallow holes from each side and having them meet in the middle.  This is what happens if your angle is slightly off and you drill through from one side.

A #11 blade was used to score the block along the pencil lines between the two holes and using a combination of files and #11 blade, the area between the score marks was shaped to simulate the sheave.  Two shallow cuts were made all around both ends of the blocks and halfway between them.  Using a V-shaped chisel, the strop grooves were cut.  The halfway cuts acted as a stop to prevent from cutting into the next block. 
 
With a sanding stick, the upper part of the block was shaped on all four sides.  I removed most of the wood between the saw cuts and start shaping the bottom of the block.  Finally, the block was cut free from the strip and the lower edge was shaped. 
 
The jeer block is located in the center of the yard.  The double strop for the jeer block is made from served 5” rope.  Just like the quarter blocks, the jeer block is not centered on the strop, but at the 1/3 mark.  The strop eyes are located on the fore side of the yard and secured with a seizing.

 
I made a template for the strop from a scrap piece of rope following the instructions below.  It took a few trials to get the correct length.  Once I was satisfied, the strop splice was unglued and the total length required was measured.  The pictures look somewhat crude but consider that the entire strop is less than 1.5” long.  These pictures are enlarged so that you can see the process.  I served a piece of rope, leaving extra unserved rope and serving thread for the splice.  The two ends were untwisted to make the splice.  This was glued and, when dry, served over with the extra serving thread.  Eyes were formed at both ends of the strop.
 
The block was positioned on the strop and seized so that one leg was twice as long as the other.  The splice is on the side of the block, where it will be less noticeable.

 
The arms were wrapped around the yard and the two loops were seized together.  These pictures show both sides of the yard.  The seizing is on the fore side. 
 
 

I completely forgot I included them on my model Chuck. At any rate some research shows that the pissdales were made of lead, copper or occasionally wood. There was a lead small discharge tube directly under the pissdale. This 1.4" tube would exit through a small scupper in the waterway. My discharge tubes are comically large.  They should only be about twice the diameter of a treenail. The pissdale discharge scupper holes on my model would be more appropriate for a herd of horses. They were discontinued after 1765.
 
I'm going to have to fix that now damn you!

The futtock shrouds are attached to the futtock stave below and the futtock plate above.  An eye with a thimble is spliced into the upper end of the futtock shroud.  A double hook connects the shroud and the futtock plate. 
To make the stropped thimble, I took some line and unfurl the end.   Using a blunt needle, I made an opening in the line approximately the circumference of the thimble away from where the unfurling stopped and fed the unfurled end through the opening.  Once the line has been passed through the opening, the opening will naturally retwist itself.  A piece of  brass tube (the thimble) was inserted into the eye and the splice was glued.  The thimble was blackened after it was stropped because handling would have caused the patina to rub off. 

The brass tube is slightly wider than the diameter of the rope.  To keep the thimble from falling out of the splice, I placed it on an anvil and tapped each open end with a center punch.  This added a slight lip to the thimble. The double S-hooks are 1/8” long and were made from 24 g wire, using round-nose pliers.  The picture shows them attached to the futtock plates.

The futtock shroud was attached to the futtock stave by wrapping around the stave and securing it to the lower shroud with two round seizings.  In the drawing, the futtock shroud is shown in red and the lower shroud in blue.  After they were installed four rows of ratlines were added.

  

Thank You...
 
With the catheads completed I could finish some inboard details at the bow in preparation for fitting the bulwarks with the pissdale and other stuff.
 
In this photo you can see the the waterway was added around the perimeter of the fcastle deck.  It was done exactly like the other decks.  
 
Then I I added the final breast hook at the bow.  This was done just like the others on the deck below it.  It was laser cut in two pieces.  I made sure to bevel the inside edge so I got a tight fit against the bulwarks and stem.  I added nine bolts that stood proud using 30lb black fishing line.   Then it was painted red.
 

 
Lastly,  I added the thin an delicate molding strip on the inboard bulwarks.   If this is made too heavy it would just look bad.  So I made sure it was very thin and not too wide.  Its a nice feature on the model actually.  You guys wont have to worry about scraping the fancy profile into a strip of wood.  I laser cut these for you with the profile.  But I didnt use wood.  I laser cut them from very thin syre-nite acrylic.  This stuff is awesome really.  It is very, very flexible.  And we will need it to be, which is why I chose to use it.  It bends so nicely without breaking.   We will need that flexibility when it has to go around the top edge of the pissdales which are up next.   I would just recommend that you round off the top edge to make it look like a nice fancy molding strip.  Just be careful and use a fine 400 grit sandpaper.  Its beige to match the wood color but I could have actually laser cut them in red.  But for those of you who want to go natural without paint I am using the stuff that looks like boxwood.  The same stuff I used for the stern lights etc.   So you must paint it red before you glue it on the hull.  
 
It runs from the aft side of the cat tail and along the sheer in the waist.  It continues all the way back to the poop bulkhead.  
 

You really must try and keep a nice run with this molding.  It should be a graceful run from bow to stern without any dips or waviness.  Follow the run of your inboard planking.  the top of the molding is flush with the top of the cap rail along the waist.
 

The fixed gangway rail:

The ladderway railings:








 

The lower yard is specified on the plans as 41.5 feet long, with a centerline diameter of 9.2”.  Just like the mast, the yard is divided into quarters.  There are four quarters on either side of the centerline.  The two center quarters are octagonal and the yard tapers from 9.2” to 7.8” at the end of the second quarter.  Because this is a desktop model, I did not want the yard to extend beyond the side of the hull and made only the middle twenty-five feet.
To make the yard, I started just like the mast, marking the dimensions on all four sides of the dowel.  Because this is such a short piece of wood, a template was not necessary.  The center octagonal section was made first.  Then I wrapped tape around the center quarters to protect them and tapered the outer part of the yards.  Finally, I rounded the tapered portions with sandpaper.  The drawing illustrates the dimensions.

 
A pin was placed in the center point of the yard to secure it to the mast.  The yard sits at the level of the futtock stave so I drilled a corresponding hole in the mast.  You can see the mast hole location in the picture in the previous post, just above the uppermost woolding.
Nine blocks were installed on the yard.  The jeer block is part of a pulley system to raise the yard.  Its configuration changed several times in the eighteenth century and varied with different sized ships.  This configuration is appropriate for a ship smaller than 28 guns in the last quarter of the 18th century.  Quarter blocks carry the topsail sheet falls.  Clew lines run from the corner of the lower sails (the clews) through the clew blocks.  The buntlines raise the foot of the sail for furling and run through the bunt blocks.   

 
The quarter blocks were installed first.  The kit will include 5 mm blocks; mine were slightly larger to be the correct length of 5.2 mm.  These blocks are stropped with served line.  This is my technique.  Serve a piece of line that you think will be the right length; on my model this was 1.6”.  This is running rigging so the serving thread is natural color.  I used Gutterman sewing thread.  Leave a long tail of serving thread on either end.

The first step was to make a loop at one end.  Untwist a short segment of rope next to the end of the serving on one side and cut the untwisted threads at a 45-degree angle to decrease the bulk.  Form a loop, with the untwisted threads laying alongside the served part of the rope.  With the tail of serving thread, wrap the untwisted threads and previously served line.  In actual practice, the untwisted line would be laced into unserved rope and then the service would continue along the loop, terminating at the throat of the loop.  Temporarily seize the block and measure how long the strop should be by wrapping it around the yard.  The loop ends do not meet; a seizing will run between the loops to secure it to the yard.  Make a kink in the rope to mark the spot.  Remove the block and make the second loop the same way.  Measure the length of the finished strop so you know how long to make the strop for the other side.
 
Reinsert the block and secure it with a throat seizing.  The seizing is located on the fore side of the mast and the block hangs below the mast.  This picture incorrectly shows the legs the same length.  Finally, the strop was wrapped around the yard and the two loops were seized together.
 
 

Over the last couple of weeks I made the catheads and bow pin rail.  These were pretty straight forward, though they required a lot of measuring, and as always I proceeded slooooowly.  It was a bit nerve wracking cutting out the sections of the cap rail.  The more hours I have into this build, the more nervous I get when I have to remove material!  This was my first time cutting sheaves into wood.  I used a technique Chuck had posted about a while back for those of us using hand tools.  I practiced a couple of times on some scrap wood before creating them on the catheads.  The results turned out decent.
 
One technique I'd like to share with you folks is when you look at where my catheads meet the bulwark you see that it's seamless.  To achieve this look I shaped the cathead as close to the correct profile as possible, and then after they were glued in place I made a mix of 50/50 wood glue/water and using the tip of a straight pin to apply, ran a thin bead down the seam.  Once dry, I then used a small paint brush to paint the red or black over the seam.  It's pretty effective on parts that will be painted.  I've found if you do the same with mat medium thinned with water, it even works on seams between painted parts and bare wood.  The mat medium is used in this case to avoid a shiny seam on the unpainted joint between the painted and non-painted parts.
 
As always, thanks for looking,
Erik

I've finished up the starboard hull planking and I must say that I'm quite happy with it. So far it's been sanded with some 180 grit sticky back sandpaper attached to soft sanders. You can find them here, just search for "soft sanders" https://www.woodcraft.com/ I prefer the coarser grit as it allows me to even out the undulations in the wood more easily than if I went with a finer grit. I'll finish up with some 320-400 in order to remove any scratches that can be seen.

I still need to add the hance piece at the quarterdeck. Once that is in I will final shape the shear of that last filler plank.

Mike

Catheads...
 
I usually hold off on making the catheads, but it just makes sense to get them done now.  It will make it easier to finish off the inboard bulwarks which will be next up.   With the catheads all done I can get the waterways in on the f'castle deck along with the pissdale and other details.
 
All the pieces are laser cut for the catheads.  Below.  I have cleaned all the char off of these pieces and they are ready to assemble.
 

The sides with the carved panels were glued on first.  First the outside cover to establish the raised panel look and then the inboard piece.  These are 1/64" thick and are sanded down even thinner afterwards.
 

Then the carved front piece and sheaves were added.  These are a hair larger than needed so you can sand them all nice and flush.
 

Then the cathead was glue to the cat tail...no worries about the seam because that will be completely covered.
 

 
Using the templates that we used to establish the hawse holes,  the position for the catheads were marked outboard.  Then the bulwarks were notched out carefully.  I used a razor saw.  The notch was made narrower than needed and not as deep as ultimately needed.  Once the basic notch was cut out, I used a good file to slowly open it up to its final size and shape.
 
You will also notice I painted the inboard cat tail red in advance.  I painted up to the seam line.  Note the chamfered edges inboard.
 

When test fit and in the final position, the inboard side of the cat tail is flush with the top of the cap rail.   But the angle of the cathead rises and so it will be above the cap rail height on the outboard side.  You can see this in the picture.  This is what you are shooting for.  The cat tail is also left longer on the inboard side so you can shorten it accordingly.  It should sit flat on the deck.  You will soon see some inboard pics.

Above the cathead there is a cat block.  Usually this is an open cat block but on the contemporary model it is closed.  So I will follow suit.  This is laser cut and 3/16" wide. ...but is currently a straight cat block.  You need to sand a slight curve into this when viewed from above.  It needs to conform to the rounded shape of the cap rail when viewed from above.  See the plans.  This is easy enough to do.  It is a very slight curve.
 
Then a sheave is added and a slot is created on the bottom.  This slot will accommodate the top of the cathead.   It will sit right on top of it and thus this slot must be angled to match the upward slope of the cathead.  Again this is not hard to do.  I just used a small flat file.  But yes you can carve it with a chisel also.   The catblock was painted black.
 

 
A final pic of the catheads in position and the cat blocks too.  There is still a bunch of paint touch up to get done.
 


Now as you know there are many ways to build and position these.  For example,  if you wanted to,  you can add the inboard cat tail separately without gluing them together first.  Maybe that will be easier for some.  Cut it to length and paint it red.  Glue it to the inboard bulwarks and partially in the notch.  Then add the cathead by placing it into the notch up against the cat tail.
 
Its up to you.  I just thought it might be easier this way to make them look like one piece if they were glued together first.  But its not the only way to do it. And remember, the seam between the two parts will be completely covered by the cat block.  So it doesnt have to be perfect.

The quarter deck breastwork:
 









 

The lower yard is specified on the plans as 41.5 feet long, with a centerline diameter of 9.2”.  Just like the mast, the yard is divided into quarters.  There are four quarters on either side of the centerline.  The two center quarters are octagonal and the yard tapers from 9.2” to 7.8” at the end of the second quarter.  Because this is a desktop model, I did not want the yard to extend beyond the side of the hull and made only the middle twenty-five feet.
To make the yard, I started just like the mast, marking the dimensions on all four sides of the dowel.  Because this is such a short piece of wood, a template was not necessary.  The center octagonal section was made first.  Then I wrapped tape around the center quarters to protect them and tapered the outer part of the yards.  Finally, I rounded the tapered portions with sandpaper.  The drawing illustrates the dimensions.

 
A pin was placed in the center point of the yard to secure it to the mast.  The yard sits at the level of the futtock stave so I drilled a corresponding hole in the mast.  You can see the mast hole location in the picture in the previous post, just above the uppermost woolding.
Nine blocks were installed on the yard.  The jeer block is part of a pulley system to raise the yard.  Its configuration changed several times in the eighteenth century and varied with different sized ships.  This configuration is appropriate for a ship smaller than 28 guns in the last quarter of the 18th century.  Quarter blocks carry the topsail sheet falls.  Clew lines run from the corner of the lower sails (the clews) through the clew blocks.  The buntlines raise the foot of the sail for furling and run through the bunt blocks.   

 
The quarter blocks were installed first.  The kit will include 5 mm blocks; mine were slightly larger to be the correct length of 5.2 mm.  These blocks are stropped with served line.  This is my technique.  Serve a piece of line that you think will be the right length; on my model this was 1.6”.  This is running rigging so the serving thread is natural color.  I used Gutterman sewing thread.  Leave a long tail of serving thread on either end.

The first step was to make a loop at one end.  Untwist a short segment of rope next to the end of the serving on one side and cut the untwisted threads at a 45-degree angle to decrease the bulk.  Form a loop, with the untwisted threads laying alongside the served part of the rope.  With the tail of serving thread, wrap the untwisted threads and previously served line.  In actual practice, the untwisted line would be laced into unserved rope and then the service would continue along the loop, terminating at the throat of the loop.  Temporarily seize the block and measure how long the strop should be by wrapping it around the yard.  The loop ends do not meet; a seizing will run between the loops to secure it to the yard.  Make a kink in the rope to mark the spot.  Remove the block and make the second loop the same way.  Measure the length of the finished strop so you know how long to make the strop for the other side.
 
Reinsert the block and secure it with a throat seizing.  The seizing is located on the fore side of the mast and the block hangs below the mast.  This picture incorrectly shows the legs the same length.  Finally, the strop was wrapped around the yard and the two loops were seized together.