Hubac's Historian

Thank you for the high praise. 
I see that the photo makes visible what the eye in ordinary life does not notice. And I see a lot of inaccuracies. Maybe I'll even try to make another attempt so that I can't be picked on in a macro photo as well. For me this is the ideal. And I have something to strive for. There are such masters who delight with their exceptional accuracy.
 
And at the same time I want to say that if you can see mistakes from the outside, you can safely talk about the problems that you have noticed. I will of course first curse anyone who sees mistakes and says that my work is far from ideal. Perhaps I will run around the computer for a while, show my tongue, beat myself with my fists in my chest and show my dissatisfaction in various other ways. But soon it will pass and I will definitely start listening to criticism. Alas, such behavior is the norm for almost every artist. It doesn't work without it. That's why I warn you in advance, so that you are ready for anything. The main thing is not to be afraid at such moments, not to show your fear of my grimaces and shouts and not to make any sudden movements. You may not even look me in the eye, sometimes that helps too. Remember, you are at a safe distance. I have rarely had time to run to people who criticize me who are more than 100 kilometers away from me. More often I've managed to cool off on the way. So that should be a calming thought too.
 
And it's also important to realize that pointing out my mistakes is very important. Because there is a possibility that my eyes may get tired and not notice the mistake. Which means I might notice the problem much later.  So after a tantrum, I'm pretty much 100% thankful for the advice. So criticism is really important to me as well. Almost as important as praise. Although who am I trying to kid? There's nothing better than praise. Thanks!!!!! THANK YOU!!!  
I'm also very happy that you're interested in reading my stories. It is also an important part of my life for me. I am not good at short stories. And I am very glad that the translator keeps the possibility to understand my stories and even the humor.

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

This business of learning to make the chains continued to confound me as I discovered yet another mistake in my process.
 
For anyone who may also be new to this aspect of the hobby - BEWARE: jewelry wire (brass/copper) is coated with an anti-oxidation layer.  Brass black will not take without first stripping the coating (acetone bath, 99% purity - available at the pharmacy), and then roughing the wire surface with ScotchBrite.  I failed to do either of these things.  For your own sake, just buy untreated, soft copper wire.
 
My first dipping in JAX brass black almost didn’t take at all.  Whatever oxidation there was, was very spotty and wiped away easily.  After thoroughly rinsing the parts in acetone, my second JAX bath did much more to blacken the parts, but the depth of oxidation was highly irregular, there were still lots of completely bright brass patches, throughout, and the oxidation that was present still rubbed off too easily.
 
What to do, now?  I quickly decided that I absolutely was not going to re-make all of these fittings, as I had at least bent them into nicely uniform parts.  The only reasonable solution, IMO, was to spray-prime the lot black:
 

After inserting the deadeyes, and any necessary touch-up, the deadeye strops looked like this:

Quite satisfactory, I think.  On the inside, bottom edge of each deadeye, I placed a drop of CA, in order to fix the orientation of the deadeye.
 
I needed to make a run of split-rings, both for the gun out-haul tackles, and for between where the chains attach to the middle wales.
 
For these, I really like how tight a twist I get with galvanized steel wire.  Given that I was going to paint these, as well, it didn’t seem quite so important what the material was, but how it behaved.


I found it quite easy to close the eyes with my parallel pliers, a decent set of which are essential for this work (Thanks Druxey!), and I sealed the rings with a spot of common, brush-able CRAZY GLUE.
 
The eyes on deck:


In preparation for the deadeyes, I made ready the channels.  Because I found it necessary to shift a handful of deadeyes, so that the chains do not interfere with the gunport lids, I found it necessary to widen a number of the channel slots.  I then drilled for short sections of .030 styrene rod, so that I could favor one side of the slot:


Next I made capping strips for the outside edges of the channels, and simulated the nailing with shallow slices of triangular styrene rod.  I used the same “heat flashing” technique to dome over the heads:

With my masts in-place and a guide-string, I penciled-in the preventer plate locations.
 
The important thing, I think, was that the join of the preventer plates and the small loop-links be in a consistent plane, along the upper middle wale - just slightly higher than mid-wale.
 
Following a tip from fellow SR enthusiast Eric Wiberg, I purchased the following dome-headed rivets:
 
https://www.eugenetoyandhobby.com/products/plastic-rivets-round-head?_pos=3&_sid=320937e14&_ss=r
 
My idea was to use these with plastic cement to secure the preventer and loop links.
 
After drilling the top preventer plate/loop-link hole, I secure the position of the preventer plate with a common sewing pin in the top hole, and then swing a short mechanical pencil arc for the bottom hole location.
 
There are very slight differences between preventer plate links, so you do have to drill specific links for a given location.  It is very fiddly to fix the plates with these tiny styrene pins, but it can be managed from the bottom up with plenty of patience and a sewing pin to guide mating eyes into alignment.
 
Now, my hope for some time and results redemption depended upon whether or not I could make appropriate diameter thread look like the long connecting links.
 
Among my stash, was some really nice line that Dan Pariser very generously donated to my cause.  Although light in color, I found I could “paint” lengths of line with two passes of a black sharpie, which also gave the line some stiffness when dry.  I found that a single bow-knot gave me the ability to introduce tension to these links:
 
Obviously, it is important to ensure that the loop links and deadeye strops are in the correct orientation to each other.
 
The proof of concept on this first link gave me sufficient confidence that this idea will produce a nice result.  It is only important that one wait to stiffen the knot with CA until after you have pulled the knot up close behind the deadeye strop loop.  On this first one, I glued before doing so, and the knot is less perfectly concealed than the others will be:

This picture above was before pulling the knot up.  Eventually, when the lower deadeyes are lashed to their corresponding upper deadeyes, these chain links will pull fully taught with just the slightest tension.
 
Here is where things stand as of now:

I quickly learned it is wise to cover the gun ports, so that you are not continually losing links into the hull.  After pinning the links in place, I brushed over the link assembly with thin CA, to give it a little extra holding power.  I then left it to dry overnight.
 
Next, I will draw all remaining loops taught, and then the whole of it will receive a thinned acrylic black wash to homogenize the assembly and touch-up any bright spots.
 
There are, of course, many better ways to go about all of this.  For me, for now - I’ll take this all as a learning experience and move-on with it.
 
Thank you all for looking-in!
 
Best,
 
Marc
 
 
 
 
 
 
 
 
 

Thank you for the nice comments.
 
The planking at the bow has been further sanded and fitted with treenails.

Back to the rear castle.
Smaller wales (4) are placed on the clinker planking. Of course, none of the four have the same dimensions.
The drawings and photos are partly used to determine the "right" location. The dimensions between the wales are also taken into account for future painting works.
According to Mary's remains, the Wales certainly continue as far as sector 10 (the penultimate cannon port)
 
"penultimate"  A new English word for me (hopefully Mr. Google translate is correct 😳)

After applying these wales I have to read my books and think first.
The "frames" of the rear castle are much too thick. And the clinker planking on the transom also feels wrong.
This means extra sanding and cutting, probably a redo and a   smiley.
 
Thanks for following
 

What a brilliant idea with the marker. I thought I was the only one who had trouble blackening brass. And here's such a great idea! Thank you. It's a great morning today, a chance to look at beautiful work and a beautiful ship. And to see some great advice. It's a great day!

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

This business of learning to make the chains continued to confound me as I discovered yet another mistake in my process.
 
For anyone who may also be new to this aspect of the hobby - BEWARE: jewelry wire (brass/copper) is coated with an anti-oxidation layer.  Brass black will not take without first stripping the coating (acetone bath, 99% purity - available at the pharmacy), and then roughing the wire surface with ScotchBrite.  I failed to do either of these things.  For your own sake, just buy untreated, soft copper wire.
 
My first dipping in JAX brass black almost didn’t take at all.  Whatever oxidation there was, was very spotty and wiped away easily.  After thoroughly rinsing the parts in acetone, my second JAX bath did much more to blacken the parts, but the depth of oxidation was highly irregular, there were still lots of completely bright brass patches, throughout, and the oxidation that was present still rubbed off too easily.
 
What to do, now?  I quickly decided that I absolutely was not going to re-make all of these fittings, as I had at least bent them into nicely uniform parts.  The only reasonable solution, IMO, was to spray-prime the lot black:
 

After inserting the deadeyes, and any necessary touch-up, the deadeye strops looked like this:

Quite satisfactory, I think.  On the inside, bottom edge of each deadeye, I placed a drop of CA, in order to fix the orientation of the deadeye.
 
I needed to make a run of split-rings, both for the gun out-haul tackles, and for between where the chains attach to the middle wales.
 
For these, I really like how tight a twist I get with galvanized steel wire.  Given that I was going to paint these, as well, it didn’t seem quite so important what the material was, but how it behaved.


I found it quite easy to close the eyes with my parallel pliers, a decent set of which are essential for this work (Thanks Druxey!), and I sealed the rings with a spot of common, brush-able CRAZY GLUE.
 
The eyes on deck:


In preparation for the deadeyes, I made ready the channels.  Because I found it necessary to shift a handful of deadeyes, so that the chains do not interfere with the gunport lids, I found it necessary to widen a number of the channel slots.  I then drilled for short sections of .030 styrene rod, so that I could favor one side of the slot:


Next I made capping strips for the outside edges of the channels, and simulated the nailing with shallow slices of triangular styrene rod.  I used the same “heat flashing” technique to dome over the heads:

With my masts in-place and a guide-string, I penciled-in the preventer plate locations.
 
The important thing, I think, was that the join of the preventer plates and the small loop-links be in a consistent plane, along the upper middle wale - just slightly higher than mid-wale.
 
Following a tip from fellow SR enthusiast Eric Wiberg, I purchased the following dome-headed rivets:
 
https://www.eugenetoyandhobby.com/products/plastic-rivets-round-head?_pos=3&_sid=320937e14&_ss=r
 
My idea was to use these with plastic cement to secure the preventer and loop links.
 
After drilling the top preventer plate/loop-link hole, I secure the position of the preventer plate with a common sewing pin in the top hole, and then swing a short mechanical pencil arc for the bottom hole location.
 
There are very slight differences between preventer plate links, so you do have to drill specific links for a given location.  It is very fiddly to fix the plates with these tiny styrene pins, but it can be managed from the bottom up with plenty of patience and a sewing pin to guide mating eyes into alignment.
 
Now, my hope for some time and results redemption depended upon whether or not I could make appropriate diameter thread look like the long connecting links.
 
Among my stash, was some really nice line that Dan Pariser very generously donated to my cause.  Although light in color, I found I could “paint” lengths of line with two passes of a black sharpie, which also gave the line some stiffness when dry.  I found that a single bow-knot gave me the ability to introduce tension to these links:
 
Obviously, it is important to ensure that the loop links and deadeye strops are in the correct orientation to each other.
 
The proof of concept on this first link gave me sufficient confidence that this idea will produce a nice result.  It is only important that one wait to stiffen the knot with CA until after you have pulled the knot up close behind the deadeye strop loop.  On this first one, I glued before doing so, and the knot is less perfectly concealed than the others will be:

This picture above was before pulling the knot up.  Eventually, when the lower deadeyes are lashed to their corresponding upper deadeyes, these chain links will pull fully taught with just the slightest tension.
 
Here is where things stand as of now:

I quickly learned it is wise to cover the gun ports, so that you are not continually losing links into the hull.  After pinning the links in place, I brushed over the link assembly with thin CA, to give it a little extra holding power.  I then left it to dry overnight.
 
Next, I will draw all remaining loops taught, and then the whole of it will receive a thinned acrylic black wash to homogenize the assembly and touch-up any bright spots.
 
There are, of course, many better ways to go about all of this.  For me, for now - I’ll take this all as a learning experience and move-on with it.
 
Thank you all for looking-in!
 
Best,
 
Marc
 
 
 
 
 
 
 
 
 

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

Another good tip with the marker pen, Kevin.  Thanks to all for the likes and looking-in!

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

This business of learning to make the chains continued to confound me as I discovered yet another mistake in my process.
 
For anyone who may also be new to this aspect of the hobby - BEWARE: jewelry wire (brass/copper) is coated with an anti-oxidation layer.  Brass black will not take without first stripping the coating (acetone bath, 99% purity - available at the pharmacy), and then roughing the wire surface with ScotchBrite.  I failed to do either of these things.  For your own sake, just buy untreated, soft copper wire.
 
My first dipping in JAX brass black almost didn’t take at all.  Whatever oxidation there was, was very spotty and wiped away easily.  After thoroughly rinsing the parts in acetone, my second JAX bath did much more to blacken the parts, but the depth of oxidation was highly irregular, there were still lots of completely bright brass patches, throughout, and the oxidation that was present still rubbed off too easily.
 
What to do, now?  I quickly decided that I absolutely was not going to re-make all of these fittings, as I had at least bent them into nicely uniform parts.  The only reasonable solution, IMO, was to spray-prime the lot black:
 

After inserting the deadeyes, and any necessary touch-up, the deadeye strops looked like this:

Quite satisfactory, I think.  On the inside, bottom edge of each deadeye, I placed a drop of CA, in order to fix the orientation of the deadeye.
 
I needed to make a run of split-rings, both for the gun out-haul tackles, and for between where the chains attach to the middle wales.
 
For these, I really like how tight a twist I get with galvanized steel wire.  Given that I was going to paint these, as well, it didn’t seem quite so important what the material was, but how it behaved.


I found it quite easy to close the eyes with my parallel pliers, a decent set of which are essential for this work (Thanks Druxey!), and I sealed the rings with a spot of common, brush-able CRAZY GLUE.
 
The eyes on deck:


In preparation for the deadeyes, I made ready the channels.  Because I found it necessary to shift a handful of deadeyes, so that the chains do not interfere with the gunport lids, I found it necessary to widen a number of the channel slots.  I then drilled for short sections of .030 styrene rod, so that I could favor one side of the slot:


Next I made capping strips for the outside edges of the channels, and simulated the nailing with shallow slices of triangular styrene rod.  I used the same “heat flashing” technique to dome over the heads:

With my masts in-place and a guide-string, I penciled-in the preventer plate locations.
 
The important thing, I think, was that the join of the preventer plates and the small loop-links be in a consistent plane, along the upper middle wale - just slightly higher than mid-wale.
 
Following a tip from fellow SR enthusiast Eric Wiberg, I purchased the following dome-headed rivets:
 
https://www.eugenetoyandhobby.com/products/plastic-rivets-round-head?_pos=3&_sid=320937e14&_ss=r
 
My idea was to use these with plastic cement to secure the preventer and loop links.
 
After drilling the top preventer plate/loop-link hole, I secure the position of the preventer plate with a common sewing pin in the top hole, and then swing a short mechanical pencil arc for the bottom hole location.
 
There are very slight differences between preventer plate links, so you do have to drill specific links for a given location.  It is very fiddly to fix the plates with these tiny styrene pins, but it can be managed from the bottom up with plenty of patience and a sewing pin to guide mating eyes into alignment.
 
Now, my hope for some time and results redemption depended upon whether or not I could make appropriate diameter thread look like the long connecting links.
 
Among my stash, was some really nice line that Dan Pariser very generously donated to my cause.  Although light in color, I found I could “paint” lengths of line with two passes of a black sharpie, which also gave the line some stiffness when dry.  I found that a single bow-knot gave me the ability to introduce tension to these links:
 
Obviously, it is important to ensure that the loop links and deadeye strops are in the correct orientation to each other.
 
The proof of concept on this first link gave me sufficient confidence that this idea will produce a nice result.  It is only important that one wait to stiffen the knot with CA until after you have pulled the knot up close behind the deadeye strop loop.  On this first one, I glued before doing so, and the knot is less perfectly concealed than the others will be:

This picture above was before pulling the knot up.  Eventually, when the lower deadeyes are lashed to their corresponding upper deadeyes, these chain links will pull fully taught with just the slightest tension.
 
Here is where things stand as of now:

I quickly learned it is wise to cover the gun ports, so that you are not continually losing links into the hull.  After pinning the links in place, I brushed over the link assembly with thin CA, to give it a little extra holding power.  I then left it to dry overnight.
 
Next, I will draw all remaining loops taught, and then the whole of it will receive a thinned acrylic black wash to homogenize the assembly and touch-up any bright spots.
 
There are, of course, many better ways to go about all of this.  For me, for now - I’ll take this all as a learning experience and move-on with it.
 
Thank you all for looking-in!
 
Best,
 
Marc
 
 
 
 
 
 
 
 
 

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

I think that's come out very well indeed Marc. Your opening line about the coated wire resonated, I think I found the same on my CS cathead levers, the blacking just rubbed off,  and I resorted to using a black acrylic marker pen. I like that it adds more or less zero 'paint' thickness, but the downside is that it has a sheen to it, though this can be made matt with lacquer. 

Excellent result, Marc!

Hi all,
 
It's been a while since I've had an update to post. Finally completed the installation of the guns to their four upper weather decks.  added quoins as well
Here are a few images. 
 
Thanks, as always, for dropping buy for a look - always so appreciated.
 
Cheers,
 

OC. thanks as always - happy that you dropped by as well.
 
-- Been much away from the shipyard as well as from home base for a while;
 
I did finally, however, finish stropping the many lines for the gun carriages. My recent focus was for the ten main deck larger carriages. Here are a few images - Next up is securely positioning the carriages then attaching all lines. Then onto the hull gun doors - I think??
Again thanks for your visit - this log is a real slow one indeed.
 
Cheers,
 

 
 
 

Hi all,
 
Patrick – yes, the magnetic panels - seemed to be the best idea given that I much later in this build decided to add lights. 
 
Peter – as always thanks
 
Mark - thanks as well - your work is so excellent happy that you like how this bit of the build is looking
 
Richard – so glad that you dropped by and are again working with your awesome Bluenose - thanks for the kind words.
 
--------------------------------------
 
It’s been quite a while since I’ve posted an update.
Started work detailing the carriages. Short text - images have some notations.
 
Thanks so much for your still continued interest in this very “slow boat to China” build log.
 
Enjoy your year-end holidays….
 
Cheers,
 

I considered buying a torch like that when I first picked up soldering supplies.  I decided, though, to see how easily a conventional soldering iron would work with the Solder-It, silver solder paste that I purchased.  There is a generous ratio of flux to colloidal silver solder, with this product, so I found that the smallest amounts make nice joins with a quick touch to the iron tip.  Like anything else, it was a process of course-correction to figure out how to use these products correctly.
 
I do know that the technically correct place to make the joints is along the straight parts, however, at this scale I was having a ton of difficulty getting my wire ends to meet nicely; I was either too long, resulting in a bowed straight, or too short, necessitating an excess solder-fill.  I also made the first batch of preventer plates too long, and I wasn't using enough solder paste on the back side to bolster the join enough for bending/shaping.
 
Dan Pariser suggested that he likes to cut meeting ends on a long bias so that they overlap like a scarf joint; more surface area produces a stronger joint.  As usually happens with this kind of thing, doing something like snipping wire ends hundreds and hundreds of times has a way of sharpening your skills and discernment for where precisely to make a cut.  At this point, I could fairly easily make those wire ends meet exactly where they need to.
 
I do appreciate the correctness of what you guys are suggesting, but the method I have arrived at is working for me in this scale, and producing the clean results that are a higher priority to me than rigorous accuracy of manufacture.  In larger scales, I absolutely would give the "correct" way a go again.

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

This business of learning to make the chains continued to confound me as I discovered yet another mistake in my process.
 
For anyone who may also be new to this aspect of the hobby - BEWARE: jewelry wire (brass/copper) is coated with an anti-oxidation layer.  Brass black will not take without first stripping the coating (acetone bath, 99% purity - available at the pharmacy), and then roughing the wire surface with ScotchBrite.  I failed to do either of these things.  For your own sake, just buy untreated, soft copper wire.
 
My first dipping in JAX brass black almost didn’t take at all.  Whatever oxidation there was, was very spotty and wiped away easily.  After thoroughly rinsing the parts in acetone, my second JAX bath did much more to blacken the parts, but the depth of oxidation was highly irregular, there were still lots of completely bright brass patches, throughout, and the oxidation that was present still rubbed off too easily.
 
What to do, now?  I quickly decided that I absolutely was not going to re-make all of these fittings, as I had at least bent them into nicely uniform parts.  The only reasonable solution, IMO, was to spray-prime the lot black:
 

After inserting the deadeyes, and any necessary touch-up, the deadeye strops looked like this:

Quite satisfactory, I think.  On the inside, bottom edge of each deadeye, I placed a drop of CA, in order to fix the orientation of the deadeye.
 
I needed to make a run of split-rings, both for the gun out-haul tackles, and for between where the chains attach to the middle wales.
 
For these, I really like how tight a twist I get with galvanized steel wire.  Given that I was going to paint these, as well, it didn’t seem quite so important what the material was, but how it behaved.


I found it quite easy to close the eyes with my parallel pliers, a decent set of which are essential for this work (Thanks Druxey!), and I sealed the rings with a spot of common, brush-able CRAZY GLUE.
 
The eyes on deck:


In preparation for the deadeyes, I made ready the channels.  Because I found it necessary to shift a handful of deadeyes, so that the chains do not interfere with the gunport lids, I found it necessary to widen a number of the channel slots.  I then drilled for short sections of .030 styrene rod, so that I could favor one side of the slot:


Next I made capping strips for the outside edges of the channels, and simulated the nailing with shallow slices of triangular styrene rod.  I used the same “heat flashing” technique to dome over the heads:

With my masts in-place and a guide-string, I penciled-in the preventer plate locations.
 
The important thing, I think, was that the join of the preventer plates and the small loop-links be in a consistent plane, along the upper middle wale - just slightly higher than mid-wale.
 
Following a tip from fellow SR enthusiast Eric Wiberg, I purchased the following dome-headed rivets:
 
https://www.eugenetoyandhobby.com/products/plastic-rivets-round-head?_pos=3&_sid=320937e14&_ss=r
 
My idea was to use these with plastic cement to secure the preventer and loop links.
 
After drilling the top preventer plate/loop-link hole, I secure the position of the preventer plate with a common sewing pin in the top hole, and then swing a short mechanical pencil arc for the bottom hole location.
 
There are very slight differences between preventer plate links, so you do have to drill specific links for a given location.  It is very fiddly to fix the plates with these tiny styrene pins, but it can be managed from the bottom up with plenty of patience and a sewing pin to guide mating eyes into alignment.
 
Now, my hope for some time and results redemption depended upon whether or not I could make appropriate diameter thread look like the long connecting links.
 
Among my stash, was some really nice line that Dan Pariser very generously donated to my cause.  Although light in color, I found I could “paint” lengths of line with two passes of a black sharpie, which also gave the line some stiffness when dry.  I found that a single bow-knot gave me the ability to introduce tension to these links:
 
Obviously, it is important to ensure that the loop links and deadeye strops are in the correct orientation to each other.
 
The proof of concept on this first link gave me sufficient confidence that this idea will produce a nice result.  It is only important that one wait to stiffen the knot with CA until after you have pulled the knot up close behind the deadeye strop loop.  On this first one, I glued before doing so, and the knot is less perfectly concealed than the others will be:

This picture above was before pulling the knot up.  Eventually, when the lower deadeyes are lashed to their corresponding upper deadeyes, these chain links will pull fully taught with just the slightest tension.
 
Here is where things stand as of now:

I quickly learned it is wise to cover the gun ports, so that you are not continually losing links into the hull.  After pinning the links in place, I brushed over the link assembly with thin CA, to give it a little extra holding power.  I then left it to dry overnight.
 
Next, I will draw all remaining loops taught, and then the whole of it will receive a thinned acrylic black wash to homogenize the assembly and touch-up any bright spots.
 
There are, of course, many better ways to go about all of this.  For me, for now - I’ll take this all as a learning experience and move-on with it.
 
Thank you all for looking-in!
 
Best,
 
Marc
 
 
 
 
 
 
 
 
 

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

This business of learning to make the chains continued to confound me as I discovered yet another mistake in my process.
 
For anyone who may also be new to this aspect of the hobby - BEWARE: jewelry wire (brass/copper) is coated with an anti-oxidation layer.  Brass black will not take without first stripping the coating (acetone bath, 99% purity - available at the pharmacy), and then roughing the wire surface with ScotchBrite.  I failed to do either of these things.  For your own sake, just buy untreated, soft copper wire.
 
My first dipping in JAX brass black almost didn’t take at all.  Whatever oxidation there was, was very spotty and wiped away easily.  After thoroughly rinsing the parts in acetone, my second JAX bath did much more to blacken the parts, but the depth of oxidation was highly irregular, there were still lots of completely bright brass patches, throughout, and the oxidation that was present still rubbed off too easily.
 
What to do, now?  I quickly decided that I absolutely was not going to re-make all of these fittings, as I had at least bent them into nicely uniform parts.  The only reasonable solution, IMO, was to spray-prime the lot black:
 

After inserting the deadeyes, and any necessary touch-up, the deadeye strops looked like this:

Quite satisfactory, I think.  On the inside, bottom edge of each deadeye, I placed a drop of CA, in order to fix the orientation of the deadeye.
 
I needed to make a run of split-rings, both for the gun out-haul tackles, and for between where the chains attach to the middle wales.
 
For these, I really like how tight a twist I get with galvanized steel wire.  Given that I was going to paint these, as well, it didn’t seem quite so important what the material was, but how it behaved.


I found it quite easy to close the eyes with my parallel pliers, a decent set of which are essential for this work (Thanks Druxey!), and I sealed the rings with a spot of common, brush-able CRAZY GLUE.
 
The eyes on deck:


In preparation for the deadeyes, I made ready the channels.  Because I found it necessary to shift a handful of deadeyes, so that the chains do not interfere with the gunport lids, I found it necessary to widen a number of the channel slots.  I then drilled for short sections of .030 styrene rod, so that I could favor one side of the slot:


Next I made capping strips for the outside edges of the channels, and simulated the nailing with shallow slices of triangular styrene rod.  I used the same “heat flashing” technique to dome over the heads:

With my masts in-place and a guide-string, I penciled-in the preventer plate locations.
 
The important thing, I think, was that the join of the preventer plates and the small loop-links be in a consistent plane, along the upper middle wale - just slightly higher than mid-wale.
 
Following a tip from fellow SR enthusiast Eric Wiberg, I purchased the following dome-headed rivets:
 
https://www.eugenetoyandhobby.com/products/plastic-rivets-round-head?_pos=3&_sid=320937e14&_ss=r
 
My idea was to use these with plastic cement to secure the preventer and loop links.
 
After drilling the top preventer plate/loop-link hole, I secure the position of the preventer plate with a common sewing pin in the top hole, and then swing a short mechanical pencil arc for the bottom hole location.
 
There are very slight differences between preventer plate links, so you do have to drill specific links for a given location.  It is very fiddly to fix the plates with these tiny styrene pins, but it can be managed from the bottom up with plenty of patience and a sewing pin to guide mating eyes into alignment.
 
Now, my hope for some time and results redemption depended upon whether or not I could make appropriate diameter thread look like the long connecting links.
 
Among my stash, was some really nice line that Dan Pariser very generously donated to my cause.  Although light in color, I found I could “paint” lengths of line with two passes of a black sharpie, which also gave the line some stiffness when dry.  I found that a single bow-knot gave me the ability to introduce tension to these links:
 
Obviously, it is important to ensure that the loop links and deadeye strops are in the correct orientation to each other.
 
The proof of concept on this first link gave me sufficient confidence that this idea will produce a nice result.  It is only important that one wait to stiffen the knot with CA until after you have pulled the knot up close behind the deadeye strop loop.  On this first one, I glued before doing so, and the knot is less perfectly concealed than the others will be:

This picture above was before pulling the knot up.  Eventually, when the lower deadeyes are lashed to their corresponding upper deadeyes, these chain links will pull fully taught with just the slightest tension.
 
Here is where things stand as of now:

I quickly learned it is wise to cover the gun ports, so that you are not continually losing links into the hull.  After pinning the links in place, I brushed over the link assembly with thin CA, to give it a little extra holding power.  I then left it to dry overnight.
 
Next, I will draw all remaining loops taught, and then the whole of it will receive a thinned acrylic black wash to homogenize the assembly and touch-up any bright spots.
 
There are, of course, many better ways to go about all of this.  For me, for now - I’ll take this all as a learning experience and move-on with it.
 
Thank you all for looking-in!
 
Best,
 
Marc
 
 
 
 
 
 
 
 
 

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.

So, I had a small pocket of time to snug and snip the fore, port channel. I was able to finesse that first knot up a little higher. Really - and considering that they do tighten up just enough more under slight tension - I am very pleased with this experiment. Black touch-up paint to follow:


I am at least confident that these long links would not look better as wire. I may have over-calculated the angle of the two furthest aft preventer plates, but I was just following what the test line told me to do. Also, technically, the preventer plate links should span to the lower wale, but the first batch I made just looked over-long. I can live with this compromise. It is still a vast improvement over the stock kit. The important thing is that the chains no longer interfere with the port lids.

There are three backstay deadeyes that I have yet to prepare, but I will get to them in the next few rounds of deadeye prep.