jfhealey

I went a bit over the top with balsa wood and body filler. I have no confidence in my ability to single plank this ship however. It wasn't much work nor any great cost and it does give me a sporting chance of a half decent outcome. I actually intended only to fill a few bulkheads at the bow but got carried away.

I've been spooked by Matthias' problem with the quarter gallery. Matthias/Chuck: I have a 4mm space between the false window and the hull. It's a consistent 4mm form top to bottom (it does not appear so in the photo) and is the same on both sides. Is that enough or should I sand away a little more? Thank you in anticipation of your reply.

Fred

You and Scrubby J win the most interesting workplace prize by a country mile in my book.

Fred

Thank you Chuck. I'm going along slow and steady!

I made the bollard posts and was quite pleased until I offered them up and found I had not filed anywhere near enough angle. I think I will cut new blanks on the scroll saw with the bed set to the required angle. I can't get the hang of neatly filing it. Then chapter 1 is about done.

Regards to all

Fred

I've put in the additional bits of wood below the counter. I'm happy with the transition from vertical to horizontal where stern post meets counter(having read and re-read stuntflyer mike's log). The outer bottom corner of the counter has a nice definition but not so on the left where I think I over-sanded. My plan is to sand the counter back to the frame on the correct (right hand) side and then trace that over to the left.

I think you are very brave Ben. I've got enough on my hands without adding on extras. But its a great idea and I shall watch with great interest.

Fred Healey

It is a very gentle curve. The cills on mine don't curve quite enough. I don't think it matters. We'll see when I come to put the laser cut parts on (the fit seems good). But  it was a silly mistake.

I sometimes think I shall make so many mistakes through inexperience that I should buy Chuck's laser cut bulkheads and start a second Winnie running a chapter behind the one I'm presently building. That way I'd hopefully make all the mistakes on the first and have no excuse for going wrong on the second. I shall review at the end of chapter 2!

Fred

Thank you Chuck.

Thank you Mark. I've just been to check.You're right. They are not in a straight line but they do not curve as much as the windows on the laser cut transom piece that covers them and clearly they should. I'm going to have a think about it. I'm not sure it matters. If it does I'll have to get a file out and see what I can do. Good spot and thanks for drawing it to my attention.

Fred

These are all familiar (but not very good - I need to think about my backdrops) pictures.

I didn't find the stern frames at all easy. I cut my own bulkheads rather than using the laser cut parts and I found that any slight inaccuracy at the junction of the bulkheads and the bulkhead former produces a big difference at the ends of the frames. But , with slow and steady as my watchwords I filed away and got them I think tolerably well lined up. The stern window guides were essential. The sharp eyed will see I had to push two of the frames over a tiny bit with a brace off the bulkhead former. It all seems OK - the gap around the window aperture is nice and even.

I'm not quite sure of the junction between between frames ST C/D and the bottom of the counter/incoming planking. I'm studying all the other build logs. I know I have a couple more bits of wood still to go in. I suspect it becomes clear as you work on it.

Faring the outside I thought quite therapeutic. One or two of my bulkhead horns were out - just by a couple of millimetres and only it seems right at the top. I suspect inaccurate filing of the slots in the bulkheads. I will go through and spend as much time as I need making sure everything looks OK before planking otherwise I will, have unwelcome rises and falls.

Its blowing a gale and lashing down with rain here in Cornwall (UK) so a good day for some boat building.

I'm thoroughly enjoying the project. Thank you Chuck for creating it!

Fred

I'm intruiged by your work place. Surely you are not making saw dust in that environment!

I'm delighted to see someone using filler to get all the contours correct. I wasn't brave enough to admit that's my plan.

Good luck with the transom.

Fred

superb! You must be very proud of your model. I certainly would be.

Fred Healey

I wish looking back I'd taken a little more trouble lining up the outer edges of my plywood fillets. They look scrappy and though they will all be covered up in due course it irritates me. Oh well -live and learn.

The last three frames are not yet glued in. I have not filed the rabbet on the BF yet. That's todays job.

Fred

I've gone off piste a bit - in two respects. First I've inserted plywood fillets between the frames. It does make the whole structure absolutely solid. I hope that will make sanding and planking easier. I haven't the confidence to do either out of a building frame. Secondly I've left off the beautiful Syren laser cut prow. I feel certain I would break it or damage it over the course of sanding. I think I can align it correctly when the time comes.

I know if it all goes pear shaped I can simply purchase the Syren bulkhead package but I'm happy going along this way for the moment.

Fred

Thank you Chuck. I've taken great pleasure following everyone's build logs. I'm very conscious that with only two build to my name - Amati's Lady Nelson and AL's Bounty - I'm batting too high up the order for my skill level but nothing ventured nothing gained.

I thought very hard before joining the project. The deciding factor - by a country mile - was having Chuck's guidance at every stage. What a way to learn .

Fred

I'm disappointed to see I'm more than 55,900 views behind that fellow Chuck. Still, he started before me.

Fred

Ah Ha!

Good evening everyone from Cornwall.

Now I only have to work out how to post photos.

I took Chuck at his word as to the cost of shipping from the USA and bought a Proxxon scroll saw and an 8' x 4' piece of Russian Birch ply (for I guess about the same cost, and began work on January 5. I've broken about 8 blades, exhausted ferocious concentration, still have all my fingers and I'm quietly pleased with the result. I'd put up a picture but that may have to await the return home of one of my children to show me how.

Fred 

If I press this button will I, I wonder, open a new build log