Jump to content
MSW Spring Donation Drive

lraymo

Members
 View Profile  See their activity

  • Posts

    235

  • Joined

  • Last visited

 Content Type 

Everything posted by lraymo

  1. lraymo
    Just now getting back to work on the sail! I was nervous, but using some tips from the various blogs, its turned out ok so far. Used Mod Podge to coat the sail fabric (instructions said to use watered-down glue, which is what Mod Podge claims to be), and it worked out well. Also, realized too late that someone had mentioned pencil marks are hard to erase after coating. So now I have a few permanent pencil marks. So far, so good. Next is tackling all the rigging. I will need to read the instructions a few more times, as I'm still not sure about it, and I'll need to revisit some of the blogs to get a feel for what needs to be done! The sail is complete!
  2. lraymo
    Hi Keith, yes, doing fine, and thanks for asking! Progress had stalled for a bit, while other life issues got in the way, but working towards getting back to it! Had to remove/relocate the workshop (a.k.a. kitchen table) to accommodate guests, but slowly getting back to modeling. Workbench prior to guests: Ready for guests to arrive, but alas, model work had to stop!
  3. lraymo
    It's been a busy "life" week, so just now getting back to the model. Finished the mast. I wasn't completely sure about the fittings. I created the halyard sheave (to the best of my ability without splitting the wood!). But I wasn't sure about the "shroud eye" (I just assumed that was where the straps for the back stays were located,so I glued them in, complete with bolts!) And it says "drill hole for halyard block", so I assumed that was the pre-drilled hole in the mast from the kit? Anyway, I think I've finished the mast, unless I've missed something. Next is the boom and gaff. Slowly getting there.
  4. lraymo
    Thanks Keith and Eric, for the explanations! I hadn't considered then question of whether I was building for the sake of the model or trying to replicate real life! I think I just assumed the kit was focused on what the ship would look like in real life, and I think that's the look I was hoping for. But I like Eric's idea to not mix & match. You both have given me alot to think about. For the Norwegian, I'll finish it up in brass, since I'm almost done with the metalwork. But going forward, I'm going to be doing research on whatever ship kit I get, and try to go for realism. At the moment, I'm considering getting the 3rd ship in the series, after I finish this one, since I need sooo much more practice in building up skills! thanks again! And btw, thanks Eric, for the kind words you left on DPhilBrick's build log about my blog questions!
  5. lraymo
    Hi DPhilBrick... looking good! I used the rubber band method too. Nice job so far. (And thanks, Cathead), for the mention!)
  6. lraymo
    Ok, my question is this, regarding brass blackening. Are you saying that all brass pieces should be blackened? Nails too? Or is there a standard for what kinds of pieces need to be blackened? I read several threads on how to blacken (looks like there are several products out there that can be applied to brass to blacken them)... but how does one determine which pieces should be blackened? Thanks!
  7. lraymo
    Druxey, yes I did! I remembered you gave me that advice, and I adopted it! Thanks, and it worked like a charm!
  8. lraymo
    Finally drove the remaining nails into the rudder gudgeons, rudder, and one oarlock pad. Lost a few more nails (slippery little things!), but I've ordered a pack of 100 nails so I should be able to finish the rest of the oarlock pads, and whatever else comes up. I also ordered the hemostat, which should help me hold on to these tiny pieces! (thanks, Keith, for the suggestion). In driving the nails, I scratched some of the transom, and had to repaint a bit. Also, I didn't trim off enough of the nail in some spots and pushed it out the other side. Lessons learned. Be sure to trim off enough of the nail, and be more careful (i.e., patient) when working on tiny items! Next step... the (gulp) mast!
  9. lraymo
    Ahh, Retired Postmaster! That makes much more sense! Happy retirement, and enjoy the Pram!
  10. lraymo
    @Retiredpm, I just looked at your Dory. Very nicely done! I had fun with mine, and it was quite the learning curve, as I am a rank beginner! I think you will enjoy the Pram. I am encountering all sorts of issues along the way, as you can tell, but its all part of the learning curve. Have fun! And all the build logs have been (and still are) very helpful along the way! (On a side note, I am also a "retired project manager" (if that's what your username is referring to!)
  11. lraymo
    Thanks, Steve, Druxey, and Keith, for your encouragement! I am doubting my abilities, but as you all say, it's all part of the process. So today, I attached the pintles to the rudder, and I can actually connect the rudder to the transom. Small steps!
  12. lraymo
    Keith, you are so funny! I appreciate your posts and your encouraging words! When I was thinking I'd have to quit, one of the things that made me continue forging ahead are the comments from you and others on this forum, and I would miss them! (I went ahead and ordered the nails!!!) I will also look into the hemostats. Interesting tool!
  13. lraymo
    Moving forward slowly! The stay plates went in with no problem, but the rudder gudgeons were really difficult. I tried seven or eight times to make the gudgeons. Cutting the (now annealed) tubing wasn't difficult, but gluing it to the little metal strap was extremely difficult for me. I kept gluing the completed strap & tube assembly to the transom, but then trying to line up the holes in the tubes didn't go well, and I kept pulling the tube away from the metal strap. I re-assembled the pieces, but I never succeeded in getting them attached as a unit. So I disassembled everything, scraped off all the CA glue, and put the straps back on with a "bend" that will hold the rudder pintles, rather than the little tubes. (I saw it done this way in another blog, and it looks like it can work) I have to admit I was really discouraged at this point. I just don't seem to have "steady hands" that can deal with such small pieces! So I moved on to the pintles. These seemed to work a bit better, although the sides are uneven, but I hope I can attach them to the rudder without issue. Meanwhile, I noticed that the kit seems to call for about 22 brass nails, but only 16 came with the contents, and I lost one when it fell/rolled off my work table! So, I am going to wait till all the fittings are installed, and then determine which plates/straps/etc actually need a nail to look good. Since only one side of the rudder will be seen, depending on how I display it, I can save a few nails that way, but I'm short at least 5 nails. I did notice that I could buy more brass nails, so I may do that as well! This is an exercise in patience, as I started to question my ability to work on such a small scale. But hope springs eternal, so I'm moving onward!
  14. lraymo
    You aren’t going to believe this story!!! I went to the local Hobby Haven (its a model shop frequented by people (mostly men) who are VERY serious about their modeling), and I asked about the annealing process, and showed them the brass rod and tube I am needing to work on. A guy who was buying something overheard me talking about needing to heat up the brass, and said, “hey, I’ve got a torch in the truck, I’ll do it!”. Turns out, he’s a plumber, and we walked out to his BIG work truck in the parking lot where he pulled out a torch and some pliers. He fired up the torch, spent about 2 minutes heating the brass, cooled the pieces in a puddle on the asphalt (its been raining a lot!), and drove off after I thanked him profusely! Not only am I extremely happy that he did the work for me, but now that I’ve seen it done, I am not so scared of it, and believe I can tackle it in the future, if needed. Also, I purchased a flush cutter while I was in the store. So I used the cutter to trim the tiller a bit more (it looks more like a rivet now), and then I attached the fore stay plate, sawed an appropriate bit of tubing to represent a hex nut, and glued it all in using CA. It’s a little bit crooked, the bend could’ve been better, and its not precise, but I am THRILLED to have done my very first piece of metal work! Thanks to all of you for your great advice and encouragement! I’m forging ahead!
  15. lraymo
    Strange indeed! I also found this set on Amazon. Ceramic tile, tweezers, etc for $34.50. So I'm getting closer to it! Still VERY nervous about actually doing the annealing, though. https://www.amazon.com/gp/product/B073FZRY59/ref=ox_sc_act_image_1?smid=A3QWCV2337YR2W&psc=1
  16. lraymo
    Keith, thanks for the video. Very good info. I'll be watching it a couple more times to really understand. And strangely, when I click on the Amazon link above, it still comes up with $21.99. Cyberspace is weird!
  17. lraymo
    I may have hit a wall. So I'm going to ask a bunch of questions, regarding the need to "anneal" the tiny brass rod and tiny brass tube in my kit. I did some online research, and it says I need to heat the brass till it turns cherry-red, then cool it by placing in a basin of water. And then clean up the pieces. So I will buy a creme brulee torch (I don't have one), but I can get one from Amazon for about $21. Does this one look ok? Amazon.com: Kitchen Torch, blow torch - Refillable Butane Torch With Safety Lock & Adjustable Flame + Fuel gauge - Culinary Torch, Creme Brûlée Torch for Cooking Food, Baking, BBQ + FREE E-book, 1 Can Included: Home Improvement To actually do the annealing, I have the following questions: Baking sheet - can I just put the tiny brass pieces on a baking sheet, and then torch them till they turn cherry-red? If I blast them, will the flame push them around on the sheet? In other words, do I need some sort of special tweezers to hold them while I blast them? And what kind should I get, as to not burn myself when I try to pick up the pieces. Once they have been super-heated, do I just need to pick them up (with the aforementioned special tweezers) and put them in a basin of water to cool them down? Rather than a baking sheet, do I need to use a ceramic plate? If so, what kind and where can I find one? What's the best way to clean the pieces (if needed). Am I on the right track here? Is this the correct process? Just trying to understand everything I need to do. Thanks!
  18. lraymo
    Thanks, I'll be perusing amazon! I've finished the tiller, having gone as far as I'm willing to go! I added the extension (after about 8 re-dos!). The final "pin" isn't in the end of the extension, but I propped it up, and I think it will look ok going forward. My next challenge, which is quite scary, is the annealing of the remaining brass rods and brass tube. Apparently I need a blowtorch, a ceramic plate, and some cutters that can handle tiny pieces of brass tubing. I need to screw up the courage to work with a blowtorch! I may try to borrow a mini torch from some friends, or maybe even try using a kitchen creme brulee torch, if that will work, but I'm WAAY out of my element when it comes to working with flame and butane fuel! Any suggestions would be welcome!
  19. lraymo
    Second try. Tiller turned out much better, although the brass rod is still too long (my wirecutters couldn't get close enough to the wood). Used superglue to secure the rod, filed down the rod ends, although didn't really make much of difference... but didn't want to keep working on it, concerned I might break something! The bigger problem is the tiller extension. The instructions say to use the 1/16" diameter rod as a pin in the end of the extension. However, the thickness of the extension is also 1/16". By using a drill bit that can accommodate the rod, it splits the wood, since they're both the same size. I'm thinking of just using a bit of the supplied 1/32" diameter rod... but giving up for tonight! Thanks for listening! And for providing all the good suggestions!
  20. lraymo
    Keith, i love your suggestions! I just ran out to the local hardware store to get a caliper! I'll drive out to the local Harbor Freight store tomorrow for the other tools and knife set. Thanks! I'm re-doing the part, per Tigersteve, but I won't attempt the rivet at this point. It's a lovely rainy day here, a nice time to work on this. I've soaked the tiller in isopropyl alcohol, taken it all apart, and now I'm making new replacement parts and will attempt to re-assemble the whole thing, with the correct hole/drill sizes, and not trying not to split the wood this time. Tnanks again!
  21. lraymo
    Thank you, thank you for these great suggestions! Druxey, I'm going to do as you said, and I can see a trip to the local hobbyshop is warranted, as I will need broaches, mini butane torch, jewelers saw, etc. and Tigersteve, re-doing this will give me an opportunity to practice what I need to do! I'm going to go for it! Thanks!
  22. lraymo
    Thanks for the advice. Here's my current problem... in assembling the tiller, I used a pin vise and drill (i bought that same set from MicroMark, and also a #55 drill bit)... but the instructions didn't say what size drill to use. It just said "drill a small hole", so I used the #55. The hole went well, but when I tried to insert the brass rod, it split the ends. I glued it all back together (I know it doesn't look very good), and then I tried to "flatten out" the ends to make a rivit. That didn't work either. It sortof bent the rod in between the wood. My wire-cutters "pinched" the end, which may be why I couldn't flatten the ends. I'm thinking I need broaches (to ream out holes after I drill them). And I don't really know what to use to make the rivit or to cleanly cut the rod. I only have a regular hammer (much too big!), and wirecutters. I think I need better tools! Any advice on what more to get? It's getting frustrating, I think mostly because I don't have the tools I need. Ah, the joys of learning! I photographed this at an angle to show the split wood. And I was able to use my magnifying glass AND the zoom on the camera to get up close, so you can really see what a mess I'm making! Ugh!
  23. lraymo
    Wow! Absolutely beautiful! Amazing precision and detail!
  24. lraymo
    Ay yi yi! Lots going on with this pram! Started painting, using the paints from the kit. Pleased with the Warm White outside of hull, and with the Clear satin finish as well. Used the Copper Red inside the hull. Then came the floor boards. First, I had to trim off about an 1/8" on both sides of each floor board. Then, not feeling very steady-handed, I laid out the floor boards upside-down on some painters tape (for easy removal), and glued them as a "unit" into place. Creating another template for the aft floorboards, I needed to trim these as well, and again, used tape to install these as a "unit of 6" rather than 1 at a time. Experiment 1 - tried some "Minwax Golden Oak" stain on the stern sheets. Didn't like it, so turned it over and tried to do a better job of staining the other side. That didn't work either! Experiment 2 - Painted the stern sheets with the Yellow Occre from the Dory kit. Liked the effect, so went ahead and painted the thwarts as well, and beveled and re-sanded the stern sheet too. Worked to bring back the "flush mount" which I had achieved originally, but after using the opposite side for painting, I couldn't get it sanded enough (I was afraid I would sand too much off), so I left it as is. I'm ok with how it turned out, though.' Meanwhile, reading ahead, the author talks about "driving home" some bolts. Question - since these bolts are thin as needles, how do you "drive these home"? Use a thimble to push it? Use pliers to grip the bolts and push it into the wood? Is there a small tool/hammer to use? Your advice? One more question: I love reading everyone's blogs and seeing the pictures, but are there any YouTube videos which show details of rigging, masts, and metal work? I've done some rudimentary searches, but haven't found any. As always, thanks for your feedback! Experiment 1 - I didn't like the white-ish mark left by the stain on the side of the stern sheet Experiment 2 - liked the paint, but now need to re-sand and re-bevel the stern sheet. Current status - Liked the look of the completed paint job. And getting ready to start working on the tiller and (gulp!) some of the metal work! Fingers crossed!
  25. lraymo
    Your Dory looks wonderful! Love the color. The Dory was my very first introduction to wood modeling, with a huge learning curve. Loving how yours is turning out!

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...