Jump to content

HMS Fly by Richard Feliciano - 1:48 scale


Recommended Posts

Working on this model for about a year. Made many mistakes but still plugging along. 

Admiralty workshops that I have attended in the past have helped a lot.

The Sea Watch books covering the construction of this model are indispensable. 

Bow Framing 2 Sep 2020.pdf Bow Framing Sep 2020.pdf Stern Framing Sep 2020.pdf Swan Typical Frame Assy.pdf

Link to comment
Share on other sites

Hi Richard,

 

Here's the instructions on how to upload photos:   

 

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Please do go with the jpgs.  I agree, most folks will not open the attachments.  When I attach a jpg here , it takes the same as a pdf, a second or less.  

Thanks!

Allan

PLEASE take 30 SECONDS and sign up for the epic Nelson/Trafalgar project if you would like to see it made into a TV series.   Click on http://trafalgar.tv   There is no cost other than the 30 seconds of your time.  THANK YOU

 

Link to comment
Share on other sites

  • 3 weeks later...

My take on porthole construction:

 

1. I like the approach of previous posts that used templates for the construction of framing about the portholes (see photo)

2. First I cut the sill slots on one frame only. 

3. I trim the next frame (base of sill using the template to determine where to cut.

4. Temporarily setting the outside frame against the sill base, I mark the cut positions, remove the frame and perform the sill cuts. 

5. I set and glue one frame spacer into position and clamp (see photo). 

6. After the glue is set in step 5, I glue the short frame upright over the middle of the sill  and the final spacer into position. I use home made clamps fabricated as described on p.44 of "The Anatomy of Nelson's Ships" by Longridge. I find these clamps to be the most versatile.

 

There is some conflict with the frame positions on the building board, but I chose to use the positioning dictated by the templates which conform to the NMM plans.

 

 

 

 

20201010_145627.jpg

Porthole 2.jpg

thumbnail.jpg

Link to comment
Share on other sites

Looking good Richard. However, please check the position of the outer hawse hole. It may just be the camera perspective but it looks a bit low to me. They should be near the center of the boxing.

Greg

website
Admiralty Models

moderator Echo Cross-section build
Admiralty Models Cross-section Build

Finished build
Pegasus, 1776, cross-section

Current build
Speedwell, 1752

Link to comment
Share on other sites

  • 1 month later...
  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...