foxy Posted September 27, 2014 Share #631 Posted September 27, 2014 (edited) Lovely work there on this iconic ship. As for jumping over to other builds, it doe's give you more interest and motivation, but not to many projects I find other wise you lose the plot fast. Great research going on and build here. As Keith on his tracks, there metal with pins to make them move if ness, there's so much out there now that's usefull for all sorts of modelling. Frank Edited September 27, 2014 by foxy Quote Link to comment Share on other sites More sharing options...
clearway Posted September 28, 2014 Share #632 Posted September 28, 2014 (edited) The tracks are ye old rubber band style supplied with the kit- i have discovered a company called fruilmodel who manufacture white metal tank tracks- a very extensive range acually- so using these to replace the tamiya tracks, and any future armour builds including trumpeter and dragon models kits. Keith Edited September 28, 2014 by clearway Quote Link to comment Share on other sites More sharing options...
rfolsom Posted September 28, 2014 Author Share #633 Posted September 28, 2014 Hi Frank; Thanks for dropping by and thank you for the kind words. Moving along (slowly) I soaked 1/8" x 1/16" basswood strips in hot water for about an hour, and used the actual model to form the foremost sections of the topgallant rail, leaving to dry overnight. Once the catheads are fixed in place, these will be mounted and blended in to the rest of the railing, finally completing this step. It would have been much harder to install detailed catheads after installing the rail, so I'm happy with the progress. I'm also adding two more frame extensions near the toilets that needed to be added to the inside of the bulwarks before the rail is in place. I hope to have some meaningful pictures in the next couple of days, but I'm taking my time to hopefully prevent any major screw-ups. Cheers, ~Bob GuntherMT, clearway and popeye the sailor 3 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 1, 2014 Author Share #634 Posted October 1, 2014 Catheads are mounted, with brackets attached just inboard of the bulwarks. Also added the pins that affix the very inboard ends to the deck. Not too happy with the way the white paint turned out; I may have to clean it up a bit. Also added two more frame extensions where the toilets will sit. Now I'm finally ready to add the last of the topgallant rails. popeye the sailor, clearway, Aussie048 and 1 other 4 Quote Link to comment Share on other sites More sharing options...
NenadM Posted October 1, 2014 Share #635 Posted October 1, 2014 Good progress, Bob. Good luck with rails. Top rails give VERY visible line to model, and that can be hard to shape Quote In progress: CUTTY SARK - Tehnodidakta => scratch => Campbell plans http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-1#entry64653 Content of log : http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-62#entry217381 Past build: Stella, Heller kit, plastic, Santa Maria, Tehnodidakta kit, wood, Jolly Roger Heller kit, plastic Link to comment Share on other sites More sharing options...
rfolsom Posted October 1, 2014 Author Share #636 Posted October 1, 2014 Thanks Nenad. This is why I view the finishing of the topgallant rails a major milestone; as they are a prominant feature of the entire hull. If I can get this area down, I might now be able to progress... popeye the sailor 1 Quote Link to comment Share on other sites More sharing options...
popeye the sailor Posted October 2, 2014 Share #637 Posted October 2, 2014 nice progress Bob.....the catheads look sweet! Quote I yam wot I yam! finished builds: Billings Nordkap 476 / Billings Cux 87 / Billings Mary Ann / Billings AmericA - reissue Billings Regina - bashed into the Susan A / Andrea Gail 1:20 - semi scratch w/ Billing instructions M&M Fun Ship - semi scratch build / Gundalow - scratch build / Jeanne D'Arc - Heller Phylly C & Denny-Zen - the Lobsie twins - bashed & semi scratch dual build Billing T78 Norden in dry dock: Billing's Gothenborg 1:100 / Billing's Boulogne Etaples 1:20 Billing's Half Moon 1:40 - some scratch required Revell U.S.S. United States 1:96 - plastic/ wood modified / Academy Titanic 1:400 Trawler Syborn - semi scratch / Holiday Harbor dual build - semi scratch Link to comment Share on other sites More sharing options...
rfolsom Posted October 5, 2014 Author Share #638 Posted October 5, 2014 Thanks, Popeye. I'm still not satisfied with the white paint job on the ends; we'll see if I get the nerve to repaint or leave as-is. Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 5, 2014 Author Share #639 Posted October 5, 2014 Ok. All topgallant railing is now installed, and sanding is almost complete. Final staining will follow shortly. This is a major milestone for me, as the bulwarks are now structurally complete, and everything is tied together. It was amazing to see how these 1/32" basswood bulwarks got progressively stronger as the stanchions, panel strips, and railings were installed. divarty, WackoWolf, GuntherMT and 2 others 5 Quote Link to comment Share on other sites More sharing options...
NenadM Posted October 5, 2014 Share #640 Posted October 5, 2014 (edited) Exelent job. Everything fits well, and things come to their places. I am satisfied Edited October 5, 2014 by Nenad M rfolsom 1 Quote In progress: CUTTY SARK - Tehnodidakta => scratch => Campbell plans http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-1#entry64653 Content of log : http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-62#entry217381 Past build: Stella, Heller kit, plastic, Santa Maria, Tehnodidakta kit, wood, Jolly Roger Heller kit, plastic Link to comment Share on other sites More sharing options...
rfolsom Posted October 5, 2014 Author Share #641 Posted October 5, 2014 Thanks, Nenad. I am satisfied. Things could have been done better, (but they always could be done better; ad infinitum..) I think it's time for the rudder, now that I'm comfortable inverting the hull once again. I'll also be checking out the copper plating, and touching up any damage I don't like. As far as little sailors go, only the runaway Piggy pokes his head out from time to time... Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 5, 2014 Author Share #642 Posted October 5, 2014 Well, I was going to use the kit-supplied die-cut plywood rudder, but It seems to be missing now. I rather like the 40+ year old plywood from this Billings kit, as it is more dense than the plywood I have on hand, so I will be making the rudder stock from 3/16" square basswood (easier to shape rounded at the top), and the rudder blade from a piece of the original plywood meant for the stand. Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 5, 2014 Author Share #643 Posted October 5, 2014 Rudder blank.. GuntherMT and clearway 2 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 5, 2014 Author Share #644 Posted October 5, 2014 Blank with template, rough cut.. clearway and GuntherMT 2 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 6, 2014 Author Share #645 Posted October 6, 2014 Had to invert the hull to drill a 3/16" hole for the rudder stock. I used my trusty "T and F" drill... (thumb and forefinger; I was not about to use a power tool for this, and my pin vise is only a little larger than the bit itself..) Perls 1 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 6, 2014 Author Share #646 Posted October 6, 2014 (edited) About twenty minutes later, I drilled about 1/8" deeper than the planking and into the center keel. With sore fingers, I'll try some more later.... Edited October 6, 2014 by rfolsom clearway 1 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 6, 2014 Author Share #647 Posted October 6, 2014 Rudder is shaped; I'll dry-fit it into place before doing any detailing (coppering, painting, pintles and gudgeons, etc.) And still drilling with the T and F drill... Perls and clearway 2 Quote Link to comment Share on other sites More sharing options...
clearway Posted October 6, 2014 Share #648 Posted October 6, 2014 Looking great Bob- tells Nenad off for calling a clipper a windjammer- Jock Willis would have his hide!!!! I always prefer the T & F drilling machine too Keith rfolsom 1 Quote Link to comment Share on other sites More sharing options...
NenadM Posted October 6, 2014 Share #649 Posted October 6, 2014 (edited) Keit is right, and I appologize From Wiki: ...Windjammers are sometimes confused with clippers, but there are significant differences between them... My english ... Rummors ... Runaway pig was seen week ago somewhere around Horn ! Edited October 6, 2014 by Nenad M clearway and rfolsom 2 Quote In progress: CUTTY SARK - Tehnodidakta => scratch => Campbell plans http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-1#entry64653 Content of log : http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-62#entry217381 Past build: Stella, Heller kit, plastic, Santa Maria, Tehnodidakta kit, wood, Jolly Roger Heller kit, plastic Link to comment Share on other sites More sharing options...
NenadM Posted October 6, 2014 Share #650 Posted October 6, 2014 And watch carefully this pictures Those small notches on rudder and on stern provide possibility to make distance from rudder to stern to be narrow enough, when you start to mount hinges. I did not success to do this correctly, because I was inpatient too much, and this are really microscopic moves in such a scale. What is your plan for hinges ? Perls, Kevin and rfolsom 3 Quote In progress: CUTTY SARK - Tehnodidakta => scratch => Campbell plans http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-1#entry64653 Content of log : http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-62#entry217381 Past build: Stella, Heller kit, plastic, Santa Maria, Tehnodidakta kit, wood, Jolly Roger Heller kit, plastic Link to comment Share on other sites More sharing options...
rfolsom Posted October 6, 2014 Author Share #651 Posted October 6, 2014 Thanks for the kind words, Keith; glad to hear someone else using his T and F drill... Nenad; thanks for the detailed photo; page 153 of Campell's China Tea Clippers shows very detailed drawings of rudders, including the fairing pieces (triangular pieces running the length of the rudder and sternpost where they meet. It is too late to duplicate this on the sternpost, but I'll probably file the triangular surface onto the rudder, and notch accordingly. This picture shows the rudder in place, temporarily held by a small removable nail at the bottom. I'm not sure what material I'll be fashioning the hinges from, probably AL can, but I won't be able to solder. (I don't have the equipment yet to solder structurally, anyhow.) The rudder sits very solidly without any glue, just held by the rudder stock and small nail, so the hinges will not need to bear any loads. Kevin and clearway 2 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 6, 2014 Author Share #652 Posted October 6, 2014 Alright; I've shaped the fairing piece outline on the rudder; next will be determining where to place the notches. They are bigger than needed in order to provide clearance when removing the rudder for repairs. Also testing out gudgeons with aluminum can pieces... Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 7, 2014 Author Share #653 Posted October 7, 2014 Well now, this is weird.. I fashioned a test gudgeon from AL can (I think I washed and cut out three cans back when I was making rivet strips, and have a ton of material left to work with..) I fiddled with it off and on, on both the rudder and sternpost, ignoring the inside with the painted beer can markings.. But when I went to photo it up close, the inside read "..try it. I know you.." I swear I did not do this on purpose; but what are the chances?! Perls and Kevin 2 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 7, 2014 Author Share #654 Posted October 7, 2014 (edited) Ok, small side note to convince everyone (and myself) that I'm not losing my mind... I cut apart three or four aluminum cans several months back, flattened them out, and squared them up roughly. I have a little bin with many different sized AL strips cut from these sheets, some with rivet detail, some without. I just happened to pick out one with legible printing on the obverse side... Edited October 7, 2014 by rfolsom Kevin 1 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 7, 2014 Author Share #655 Posted October 7, 2014 Moving along... I like the way the gudgeons are turning out, and forming them over the small nails that I will use as pintles is working out well. This is mainly Nenad's technique, but I won't be soldering anything. I will probably use CA; but I'll be test fitting before a final decision is made. I will now find out where the rudder notches will be finally located; after they are cut, I can start the rudder coppering. I am very much not superstitious, but now I have the look at the back of my AL strips.... popeye the sailor and Kevin 2 Quote Link to comment Share on other sites More sharing options...
clearway Posted October 7, 2014 Share #656 Posted October 7, 2014 just goes to show truth is stranger than fiction Bob- i love it when chance throws wobblies like that Keith Quote Link to comment Share on other sites More sharing options...
NenadM Posted October 7, 2014 Share #657 Posted October 7, 2014 Hiden truth in beer can rised up and tell you message you need to know. Coincidence? A sign ? Conspirative message from runaway pig? Hmmmm rfolsom 1 Quote In progress: CUTTY SARK - Tehnodidakta => scratch => Campbell plans http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-1#entry64653 Content of log : http://modelshipworld.com/index.php/topic/2501-cutty-sark-by-nenad-tehnodidakta-scratched-campbells-plans/page-62#entry217381 Past build: Stella, Heller kit, plastic, Santa Maria, Tehnodidakta kit, wood, Jolly Roger Heller kit, plastic Link to comment Share on other sites More sharing options...
rfolsom Posted October 8, 2014 Author Share #658 Posted October 8, 2014 Fashioned a few more gudgeons and cut notches into the rudder; also coppered the trailing edge... popeye the sailor, NenadM, clearway and 1 other 4 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 8, 2014 Author Share #659 Posted October 8, 2014 Coppered inner surfaces of notches... tasmanian, Perls, popeye the sailor and 1 other 4 Quote Link to comment Share on other sites More sharing options...
rfolsom Posted October 9, 2014 Author Share #660 Posted October 9, 2014 Rudder is now coppered... popeye the sailor, clearway, tasmanian and 3 others 6 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.