Retiredpm Posted July 11, 2021 Share #1 Posted July 11, 2021 I am beginning my second build and plan on going slow to hone my skills. I see from the initial instructions that I will be buying a couple more tools. GrandpaPhil and Ryland Craze 2 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted July 11, 2021 Author Share #2 Posted July 11, 2021 I initially glued the aft transom pieces incorrectly but got the pieces separated before the glue held. I think I have the pieces beveled correctly. There is so much trial and error in this hobby that I feel like I am guessing at times, but relying on what I think look good. GrandpaPhil and Ryland Craze 2 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted July 11, 2021 Author Share #3 Posted July 11, 2021 I have my building board all set. That’s enough for one day. The next step will be planking. GrandpaPhil and Ryland Craze 2 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted July 13, 2021 Author Share #4 Posted July 13, 2021 This step looks much easier on paper than in reality. Note to self, make sure one end is dry before gluing other end. Ryland Craze and GrandpaPhil 2 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted August 3, 2021 Author Share #5 Posted August 3, 2021 I took a couple weeks off helping in-laws pack for their move to Florida. I have completed the bottom of the boat aside from a little more sanding. Should I be using some kind of filler for the bow and stern or is it okay like this? ccoyle, Ryland Craze and GrandpaPhil 3 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
druxey Posted August 3, 2021 Share #6 Posted August 3, 2021 The plank ends need to be sanded completely flush to the transoms. If there is any small gap left, then use filler. Otherwise you'll be making a lot of dust if you fill first! Quote Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series http://trafalgar.tv Link to comment Share on other sites More sharing options...
Retiredpm Posted August 3, 2021 Author Share #7 Posted August 3, 2021 3 hours ago, druxey said: The plank ends need to be sanded completely flush to the transoms. If there is any small gap left, then use filler. Otherwise you'll be making a lot of dust if you fill first! Is a regular wood filler good or is there something better for models? Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
druxey Posted August 3, 2021 Share #8 Posted August 3, 2021 I use Lepage's wood filler, natural, in the tube. Works well; dries fairly quickly and sands well, if a little dusty. Have the vacuum handy! Quote Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series http://trafalgar.tv Link to comment Share on other sites More sharing options...
Retiredpm Posted August 11, 2021 Author Share #9 Posted August 11, 2021 I did some additional sanding after adding a little wood filler. Looks much cleaner. druxey 1 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted August 11, 2021 Author Share #10 Posted August 11, 2021 Just now, Retiredpm said: I did some additional sanding after adding a little wood filler. Looks much cleaner. Papa, Ryland Craze, druxey and 1 other 4 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted August 11, 2021 Author Share #11 Posted August 11, 2021 Board cleats and mast step installed. Made the cuts for the chain plate slots. A little confused with what the length of the cut is supposed to be, so I have small slits in place and figure I can go bigger it needed. Ryland Craze, yvesvidal, GrandpaPhil and 2 others 5 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted August 13, 2021 Author Share #12 Posted August 13, 2021 I used a grey primer spray followed by some light sanding. Will start painting when I return from a convention. druxey, Ryland Craze, GrandpaPhil and 1 other 4 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
lraymo Posted August 13, 2021 Share #13 Posted August 13, 2021 Looking good! Quote Current: Model Shipways Phantom Pilot Boat Completed: Norwegian Sailing Pram Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
druxey Posted August 13, 2021 Share #14 Posted August 13, 2021 Slots should be just wide enough for the chain plates to pass through. Coming along nicely! Quote Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series http://trafalgar.tv Link to comment Share on other sites More sharing options...
Retiredpm Posted September 16, 2021 Author Share #15 Posted September 16, 2021 It’s been a while since my last post. Life gets in the way sometimes. I started the sail. Any trick to getting the creases out of it? I’ve put 2 coats of paint on the inside and 5 coats on the outside. I think it is coming along nicely. GrandpaPhil, druxey, yvesvidal and 1 other 4 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
SkiBee Posted September 16, 2021 Share #16 Posted September 16, 2021 2 hours ago, Retiredpm said: Any trick to getting the creases out of it? Before I did anything with the sail material, I wetted it and then ironed it with an iron on cotton. Now that you have put glue on, it might work and might not, but I'm sure it would leave some glue residue on your iron. Your might try it on a excess piece that you have glued before you try on the real sail. Looking good. druxey and Ryland Craze 2 Quote Current Projects: Completed Projects: Armed Virginia Sloop - Model Shipways - 1:96 Muscongus Bay Lobster Smack - Model Shipways - 1:24 Phantom New York Pilot Boat - Model Shipways - 1:96 18th Century Long Boat - Model Shipways - 1:48 Norwegian Sailing Pram - Model Shipways - 1:12 Lowell Grand Banks Dory - Model Shipways - 1:24 Link to comment Share on other sites More sharing options...
Retiredpm Posted November 18, 2021 Author Share #17 Posted November 18, 2021 Fittings placed on boom, mast, and gaff. Wow, this is microscopic work. ccoyle, druxey and Ryland Craze 3 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
SkiBee Posted November 18, 2021 Share #18 Posted November 18, 2021 Yes it is and my fat fingers didn't help Quote Current Projects: Completed Projects: Armed Virginia Sloop - Model Shipways - 1:96 Muscongus Bay Lobster Smack - Model Shipways - 1:24 Phantom New York Pilot Boat - Model Shipways - 1:96 18th Century Long Boat - Model Shipways - 1:48 Norwegian Sailing Pram - Model Shipways - 1:12 Lowell Grand Banks Dory - Model Shipways - 1:24 Link to comment Share on other sites More sharing options...
Retiredpm Posted November 27, 2021 Author Share #19 Posted November 27, 2021 I had an issue with the tiller assembly. Both pieces split as I tried to drill a hole through them. So I took a piece of scrap and a fixed that to the assembly. Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
Retiredpm Posted November 27, 2021 Author Share #20 Posted November 27, 2021 Well. It is far from perfect, but I am still happy with the outcome and can’t wait to start my next build. Not sure if I want to do the third suggested model, Muscongus Bay Lobster Smack or tackle something else. I would love some suggestions. ccoyle, Papa, bobandlucy and 2 others 5 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
SkiBee Posted November 27, 2021 Share #21 Posted November 27, 2021 Great job Quote Current Projects: Completed Projects: Armed Virginia Sloop - Model Shipways - 1:96 Muscongus Bay Lobster Smack - Model Shipways - 1:24 Phantom New York Pilot Boat - Model Shipways - 1:96 18th Century Long Boat - Model Shipways - 1:48 Norwegian Sailing Pram - Model Shipways - 1:12 Lowell Grand Banks Dory - Model Shipways - 1:24 Link to comment Share on other sites More sharing options...
Ryland Craze Posted November 28, 2021 Share #22 Posted November 28, 2021 Congratulations of completing your Pram. You did a good job on building this model. What ship model would you like to build next based on the skills you have learned? Quote Ryland Member - Hampton Roads Ship Model Society - Ship Model Society of New Jersey - Nautical Research Guild Current Build - Armed Virginia Sloop, 18th Century Longboat Completed Build - Medway Longboat Link to comment Share on other sites More sharing options...
Retiredpm Posted November 29, 2021 Author Share #23 Posted November 29, 2021 I am open to suggestions on next build. I had picked up the Navy Frigate Alfred through FB marketplace on the cheap. So I will tackle that since, at the worst, it will be good practice as I am showing a lot of patience while working on these models. Ryland Craze 1 Quote Current Build: Armed Longboat Current Build: Continental Navy Frigate Alfred - On Hold until a improve my skills Completed Build: Norwegian Sailing Pram Completed Build: Lowell Grand Banks Dory Link to comment Share on other sites More sharing options...
tlee01 Posted November 29, 2021 Share #24 Posted November 29, 2021 Good job, I am right in the middle of this build. Ready to start the tiller assembly. Ryland Craze 1 Quote Life is to short to be serious all the time. So, if you can't laugh at yourself, your not doing it right. Current Builds 18th Century Armed Longboat Finished Builds Muscongus Bay Lobster Smack Lowell Grand Banks Dory Norwegian Sailing Pram Link to comment Share on other sites More sharing options...
ccoyle Posted November 29, 2021 Share #25 Posted November 29, 2021 Congratulations on your finished model! Ryland Craze 1 Quote Chris Coyle Greer, South Carolina When you have to shoot, shoot. Don't talk. - Tuco Current builds: Brigantine Phoenix, Bf 109E-7/trop Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.